Contact Us

MAX9947ETE+T

Brand: Analog Devices
Analog Devices MAX9947ETE+T is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MAX9947ETE+T — Analog & Mixed-Signal ICs | Superb Automation

MAX9947ETE+T

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The MAX9947ETE+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

MAX9947ETE+T: The AISG Link on a Tower Mounted Amplifier, in One 3 mm Package

The MAX9947ETE+T is an AISG compliant integrated transceiver for base station and tower mounted equipment. It contains the receiver, the transmitter and the bus arbitration logic for the 2.176 MHz link that runs up the antenna feeder. Analog Devices specifies a receiver input window of -15 dBm to +5 dBm in 50 ohm, a transmitter output adjustable from +7 dBm to +12 dBm, an output emission profile that meets the AISG mask, AutoDirection so no microcontroller has to arbitrate the bus, and support for all three AISG data rates: 9.6 kbps, 38.4 kbps and 115.2 kbps. Supply is 3.0 V to 5.5 V with an independent logic supply, the body is a 3 mm by 3 mm 16-pin TQFN, and the vendor lists two part models from $7.59 at 1ku.

The receiver window is 100 to 1 in power

Minus 15 dBm is 31.6 uW and plus 5 dBm is 3.16 mW, so the receiver has to hold a 20 dB span without gain switching. In a tower installation that span is real: cable loss between the radio and the mast head varies with feeder length, and a modem that clips on a short feeder will be deaf on a long one. A receiver specified over the full 20 dB removes the step attenuator and the calibration that would otherwise be needed per site.

The transmitter has 5 dB of adjustment, which is not a power amplifier range

Plus 7 dBm is 5.0 mW and plus 12 dBm is 15.8 mW, a ratio of 3.16. This is a link budget adjustment, not a power stage. It exists so the same board can drive a short feeder and a long one while staying inside the AISG emission mask. A buyer who reads +12 dBm as a transmit power class should check the mask requirement first: the standard constrains the spectrum, and the part meets the profile at both ends of the adjustment.

18.9 carrier cycles per bit at the top data rate

The carrier is centred at 2.176 MHz, so one cycle is 459.6 ns. At 115.2 kbps one bit is 8.68 us, which holds 18.9 carrier cycles. At 38.4 kbps a bit is 26.0 us and 56.7 cycles. At 9.6 kbps a bit is 104.2 us and 226.7 cycles. The bandpass filter inside the part is specified around that carrier, which is why the data rate can change by a factor of twelve without changing any external component.

The published table, as the vendor states it

ParameterValue
FunctionAISG integrated transceiver
Receiver input window-15 dBm to +5 dBm in 50 ohm
Transmitter output+7 dBm to +12 dBm, adjustable
Carrier2.176 MHz, on-chip bandpass
Data rates9.6, 38.4 and 115.2 kbps
Bus arbitrationAutoDirection, no microcontroller needed
Supply3.0 V to 5.5 V, independent logic supply
Package16-pin TQFN, 3 mm by 3 mm
Part models and price2 models, from $7.59 at 1ku

AutoDirection is the feature that removes a part

On a shared bus, two devices can transmit at once unless something decides who owns the line. In tower mounted equipment that decision normally needs a microcontroller watching the receive path and switching the driver. AutoDirection does that inside the transceiver, so the mast head board can be a modem plus a connector, with no firmware and no arbitration state machine to validate over temperature. Fewer active parts on a mast head also means fewer things to fail where nobody can reach them.

Buyer questions

Is this a replacement for an RS-485 transceiver? No. It handles the modulated 2.176 MHz link that the AISG standard puts on the feeder, not a baseband RS-485 pair. The two are different layers and are not interchangeable, even though both are described as bus interfaces.

What stays outside the chip? The coax interface, the coupling network and the ESD protection at the connector. The independent logic supply means the host can run at 1.8 V or 3.3 V while the transceiver sits on a 5 V rail, which is why the pin count stays at sixteen.

Family page for the category: Analog and mixed-signal ICs. For the RF signal chain around the feeder see RF component sourcing, and for long lead time planning on tower hardware see component lead time solutions.

Request Quote — In Stock, 100% New & Original, Full Warranty