Contact Us

MAX8516EUB+T

Brand: Analog Devices
Analog Devices MAX8516EUB+T is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MAX8516EUB+T — Analog & Mixed-Signal ICs | Superb Automation

MAX8516EUB+T

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The MAX8516EUB+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

MAX8516EUB+T: 1 A on the Front Page, 340 mA on a 3.6 V Rail

The MAX8516EUB+T is the adjustable member of the MAX8516/MAX8517/MAX8518 low dropout regulator family from Analog Devices, in the 10-pin micro MAX package with exposed pad, 3 mm by 5 mm, on tape and reel. It takes 1.425 V to 3.6 V in and delivers up to 1 A with a 200 mV maximum dropout, an output settable from 0.5 V to 200 mV below the input, 1.4 percent accuracy over load, line and temperature from 0 C to +85 C, half a percent initial accuracy, 320 uA of operating supply current, under 25 uA in shutdown, a 500 mV feedback reference, and a 45 mV deviation for a 20 mA to 1 A load step with a 4.7 uF ceramic output capacitor.

The 1 A rating and the 824 mW the package can actually take

The 10-pin package is rated 824 mW at 70 C and derates 10.3 mW per C, which is a junction to ambient resistance near 97 C per W, and 669 mW at 85 C. One amp from 3.6 V to 1.2 V dissipates 2.4 W, three times the rating at 70 C. At 85 C the continuous current that the package supports is 669 mW divided by the 2.4 V difference, which is 279 mA. From 3.3 V it is 319 mA, from 2.5 V it is 515 mA, and only from a 1.8 V rail does the thermal limit clear 1 A.

So the 1 A figure describes the silicon, the current limit and the 200 mV dropout, all of which are real, and the board describes the continuous current. A buyer quoting 1 A from a 3.6 V input is quoting a part that will thermally cycle, and the question to ask is the input voltage and the copper area under the exposed pad, not the current rating.

25 mV of headroom at the input floor

The input range starts at 1.425 V and the output can sit no closer than 200 mV below the input, so a 1.2 V output from a 1.425 V input has 225 mV of total headroom against a 200 mV maximum dropout at 1 A. That is 25 mV of margin at full load, which a rail tolerance or a trace resistance will spend. The part is specified for 100 mV of typical dropout, so the board has room at typical and none at the limit.

The undervoltage lockout sits at 1.32 V to 1.38 V rising with 70 mV of hysteresis, which is above the 1.425 V input floor only for the falling edge, so a rail that decays slowly passes through lockout before the output has finished regulating. The current limit is 1.6 A minimum, 2 A typical and 2.4 A maximum, which is the number that decides whether a shorted load trips the regulator before the rail collapses.

Setting the output and what the 45 mV step means

The feedback reference is 500 mV, so a 1.2 V output is a ratio of 1.4 between the upper and lower divider resistors. The divider tolerance adds directly to the 1.4 percent, and the 1 uA maximum feedback bias current through the lower resistor sets the floor on the divider current. A 4.7 uF ceramic output capacitor holds the 45 mV deviation for a 20 mA to 1 A step, which is 3.75 percent of a 1.2 V output, and the datasheet states that larger output capacitance reduces it further.

ParameterPublished valueWhat it decides
Input range1.425 V to 3.6 VPost regulation from a 1.5 V or 1.8 V rail
Output current1 ASilicon rating, not a thermal rating
Dropout at 1 A200 mV maximum, 100 mV typical25 mV of margin from a 1.425 V input
Package rating824 mW at 70 C, 669 mW at 85 C279 mA from 3.6 V in at 85 C
Supply current320 uA operating, under 25 uA shutdownStandby load on the upstream rail
Current limit1.6 A to 2.4 AShorted load behaviour
Feedback reference500 mV1.2 V out is a divider ratio of 1.4
Load step deviation45 mV for 20 mA to 1 A3.75 percent of a 1.2 V output

Questions buyers ask before they order this part number

MAX8516, MAX8517 or MAX8518? All three are the same regulator with different monitoring. The MAX8517 adds a power-OK output that goes high impedance when the output is within ten percent of regulation, and the MAX8518 adds a power-on reset that releases 150 ms after the output passes 90 percent. The MAX8516 has neither, so a board that sequences two rails needs one of the other two numbers.

Is a 1 uF ceramic input capacitor really enough at 1 A? The datasheet specifies a 1 uF input and a 4.7 uF output ceramic for the full 1 A, which is a short loop and a low ESR part rather than a large bank. The input capacitor is carrying the switching edges of the pass device, so its placement matters more than its value.

The family is listed under analog and mixed-signal IC category. Rails that follow a switching stage are compared on power management cross reference, and cost reduction reviews on an existing board start from how to reduce component cost.

Half of a Milliamp: Where 320 Microamps of Quiescent Current Starts to Cost

The MAX8516EUB+T is a 1 A regulator that draws 320 uA of quiescent current and 25 uA in shutdown. On a 1 A load the quiescent current is 0.03 percent and irrelevant. On a 1 mA load it is 24 percent of the load, and the efficiency of the rail is set by it rather than by the pass element. The arithmetic of where that line falls is short, and it decides whether this part belongs on a rail that sleeps.

The quiescent current dominates below about 30 mA

At 1.8 V in and 1.2 V out, a 10 mA load draws 10.32 mA from the input once the 320 uA is added, which is 18.6 mW in and 12 mW out, 64.6 percent. At 1 mA the input current is 1.32 mA, 2.38 mW in against 1.2 mW out, 50.5 percent. At 100 uA the input current is 420 uA, 756 uW in against 120 uW out, 15.9 percent. The same rail at 100 mA is 64.9 percent, so the efficiency curve is flat from 100 mA down to about 30 mA and then falls away with the quiescent current as the reason.

The shutdown current is the number for a battery rail

Under 25 uA in shutdown is 219 mAh over a year, which is a whole coin cell. A rail that is expected to survive a year of shelf life on a battery therefore cannot be left in shutdown and must be disconnected by a load switch or a FET, and the regulator's own shutdown pin is the wrong tool for that job. The distinction is worth making because the shutdown figure is small enough to look like a solution and large enough to empty a battery.

Forty five millivolts of load step is a capacitor decision

The published deviation is 45 mV for a 20 mA to 1 A step with a 4.7 uF ceramic output capacitor. Doubling the capacitor to 10 uF roughly halves the capacitive part of that step, but the resistor part, which is the ESR and the loop response, does not halve. The 4.7 uF is also the minimum for stability, so the capacitor that gets selected for the transient is above the minimum and the minimum is not a target.

LoadInput current at 1.8 V inEfficiency at 1.2 V outQuiescent share of the load
100 uA420 uA15.9 percent320 percent
1 mA1.32 mA50.5 percent32 percent
10 mA10.32 mA64.6 percent3.2 percent
100 mA100.3 mA66.5 percent0.32 percent

The 1.4 percent accuracy is a loaded figure

One point four percent over load, line and temperature from 0 C to 85 C, with half a percent of initial accuracy. The band 0 C to 85 C is a commercial window and it is the one to check against an industrial requirement: the same family in another package option may carry a wider window, and a rail specified to minus 40 C needs the part whose table says so. The 500 mV feedback reference and the 0.5 V to 200 mV below input output range mean the divider that sets the output also carries the divider's own tolerance, so a 1 percent resistor pair adds 1 percent to the 1.4 percent before anything else is counted.

Where this part is the right answer

A rail that runs at tens of milliamps, sits behind a switcher, and needs a small body with an exposed pad for the heat is where this part fits. A rail that has to hold regulation at 1 A from a 3.6 V input cannot use it, because the package passes 279 mA at 85 C, and a rail that sleeps at 100 uA is better served by a part with a quiescent current in the tens of microamps. Those two boundaries are the ones a substitution has to respect.

The part sits on the analog and mixed-signal IC page. The component lead time page covers the schedule side, and the BOM shortage recovery page is where an alternative with the same footprint and a different quiescent current is worked through.

Request Quote — In Stock, 100% New & Original, Full Warranty