UCC14130QDWNRQ1
Product Specifications
UCC14130QDWNRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC14130QDWNRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC14130QDWNRQ1: 1.5 W of isolated bias from a 12 V rail, inside a 12.83 mm by 7.5 mm module
The UCC14130QDWNRQ1 is an automotive qualified isolated DC/DC module that takes a regulated 10 V to 18 V input and produces an isolated 12 V output from a 12 V rail, or an isolated 15 V or 18 V output from a 15 V rail, at up to 1.5 W at a 105 C ambient. The transformer, the controller and the feedback are inside a 36 pin SSOP body measuring 12.83 mm by 7.5 mm. It exists because a silicon carbide or IGBT gate driver needs a floating bias supply, and building that supply from a controller, a transformer, a rectifier and a feedback amplifier takes twenty components and a magnetic qualification that most product teams would rather not repeat.
The isolation is the headline. The module is rated above 3 kVRMS working, is planned for 5657 VPK basic isolation per DIN EN IEC 60747-17, and specifies common mode transient immunity above 150 kilovolts per microsecond, which is the number that keeps a half bridge from corrupting its own bias supply when the switch node moves in a few nanoseconds. Output regulation is better than plus or minus 1.3 percent across the operating range, and the output voltage is set by resistors, so a single code covers a positive rail, a negative rail, or a dual rail with a mid-point.
Key electrical data for the UCC14130QDWNRQ1
| Input | 10 V to 18 V operating, 32 V absolute maximum, input UVLO and OVLO both inside the module |
| Output | 12 V from 12 V in, 15 V or 18 V from 15 V in, adjustable single or dual rail by resistors |
| Power | 1.5 W at a 105 C ambient, 1.0 W over the full 10 V to 18 V input window at the same ambient |
| Accuracy | Better than plus or minus 1.3 percent regulation over the full operating range |
| Isolation | Above 3 kVRMS working, 5657 VPK basic isolation per DIN EN IEC 60747-17, CMTI above 150 kV per microsecond |
| Protection | Input UVLO, OVLO, output power good comparators, overcurrent, short circuit, undervoltage, overtemperature, soft start timeout |
Package, marking and reel data
| Body | DWN, 36 pin SSOP module, 12.83 mm by 7.50 mm, integrated transformer |
| Reel | 750 pieces on a large reel, the only published row for this code |
| Grade | AEC-Q100 grade 1, junction -40 C to 150 C, ambient -40 C to 125 C |
| Certification | Planned 5657 VPK basic isolation per VDE 0884-17, functional safety capable with documentation |
Where an isolated bias module replaces a discrete flyback
A three phase inverter needs six floating gate supplies, three high side and three low side, and each one has to hold its regulation while the switch node slews. A discrete flyback per channel needs a transformer with a reinforced insulation system, a controller, a rectifier, an output capacitor and a feedback path, and every one of those parts has to be qualified for the isolation voltage. The module collapses that into one 12.83 mm by 7.5 mm part with the isolation already certified, and the only external work is the input capacitor, the output capacitor and the resistor pair that sets the rail.
The 1.5 W figure is quoted at a 105 C ambient, and it falls to 1.0 W when the input sits anywhere in the 10 V to 18 V window rather than at the nominal point. A gate driver that draws 1.2 W therefore needs the derating checked against the actual input voltage, not against the headline. Spread spectrum modulation is built in, which helps the conducted emission scan that an automotive module has to pass. Our power management cross reference page lists the isolated bias parts we hold alongside this one.
Buyer questions on the UCC14130QDWNRQ1
Can one module drive two gate drivers? Yes if the total draw stays inside the derated power figure and the two drivers share the same reference node. Two high side drivers on different phases cannot share, because each needs its own floating common.
Does the output need an external diode or inductor? No. The transformer and the rectifier are inside the module, so the external parts are the input capacitor, the output capacitor and the setting resistors.
What is the reel size? 750 pieces on a large reel. That is the only published row for this code, so a prototype quantity comes from a broken reel and the date code has to be recorded.
Availability and cross reference
This is an automotive grade part with a functional safety documentation package, so the traceability requirement is higher than on an industrial module: the lot has to be traceable to the reel and the certification has to travel with the shipment. We hold the code against forecast rather than in open stock, and our sourcing audit trail page describes the record set that ships with an automotive bias module.