LT3741EFE#TRPBF
Product Specifications
LT3741EFE#TRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LT3741EFE#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LT3741EFE#TRPBF: A 20 A Current Source With a VIN Minus 2 V Ceiling
The LT3741 is a fixed frequency synchronous step down controller that regulates output current rather than output voltage, up to 20 A, from a 6 V to 36 V input, with plus and minus 1.5 percent voltage accuracy and plus and minus 6 percent current accuracy. The regulated current is set by an analogue voltage on the CTRL pins and an external sense resistor. It can source and sink current; the LT3741-1 drops the sink capability for parallel operation.
The ceiling that decides the rail
The output voltage range runs from 0 V to VIN minus 2 V. On a 12 V rail that is a 10 V ceiling, on 24 V it is 22 V, and on 36 V it is 34 V. A board that needs 12 V out from a 12 V input cannot use the part in a step down configuration no matter how the divider is set, and the 2 V is headroom for the high side switch and the bootstrap, not a tolerance. This is the first thing to check before the current accuracy matters.
What 6 percent current error looks like
At 20 A the current accuracy of plus and minus 6 percent is 1.2 A. For an LED string or a battery charge that is the spread between units, and it is wider than the 1.5 percent voltage loop, so a board that uses the current loop as a precision meter needs calibration. The 20 A into a 5 milliohm sense resistor develops 100 mV, which is also the size of signal the current amplifier works with; a 10 milliohm shunt doubles the signal and doubles the loss.
Average current mode control keeps the inductor current regulated across the full output range, which is what makes the part usable as an electronic load or a battery discharge sink. The switching frequency is programmable from 200 kHz to 1 MHz with a resistor on the RT pin or by synchronising to an external clock, and a thermal control pin allows the load current to be derated by a temperature signal rather than by a shutdown.
| Input range | 6 V to 36 V |
| Output current | up to 20 A, source and sink (LT3741-1 sources only) |
| Output voltage | 0 V to VIN minus 2 V |
| Accuracy | plus and minus 1.5 percent voltage, plus and minus 6 percent current |
| Control | average current mode, CTRL pin sets the current |
| Switching frequency | 200 kHz to 1 MHz programmable or synchronised |
| Efficiency | up to 94 percent |
| Shutdown current | below 1 uA |
| Extras | thermal control of load current, programmable UVLO with hysteresis, soft start |
| Package | 20 pin FE package, 4 mm by 4 mm QFN |
Where it fits
Battery charging and discharging, LED strings driven from a rail above the string voltage, thermoelectric cooler drive, and electronic loads that must absorb current. The sink capability is the differentiator: a pure step down regulator cannot pull current out of a battery, and a discharge test rig needs exactly that.
Order code and availability
EFE is the industrial grade in the 20 pin FE package, and the -1 variant is the order code for parallel or source only use. The controller family is on the analogue and mixed signal line card.
Common questions
Can two LT3741 share current? The -1 variant is the one intended for parallel operation, because the sink capability of the standard part fights a second source on the same node. Sharing also needs the CTRL pins driven from a common reference so both loops aim at the same current.
Why is the current accuracy wider than the voltage accuracy? The voltage loop is a divider against an internal reference, while the current loop depends on an external sense resistor and the amplifier offset across a 100 mV signal. The shunt tolerance adds directly to the 6 percent.
Current source parts are grouped on the power management cross reference page, and socket checks before a substitution are on the pin to pin page.
Request Quote — In Stock, 100% New & Original, Full Warranty