Contact Us

TPS92511DDAR

Brand: Texas Instruments
Texas Instruments TPS92511DDAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS92511DDAR — Power Management & Signal Chain | Superb Automation

TPS92511DDAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS92511DDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS92511DDAR: 65 V, 0.5 A constant current buck for LED strings, no sense resistor

TPS92511DDAR is a constant current buck converter for a single LED string rated 0.5 A from a 65 V input in a HSOP body of 8 pins. It regulates the string current without a current sense resistor and without an external compensation network, which brings the external component count down to five. Switching frequency is set from 50 kHz to 500 kHz by a resistor, current accuracy is 3.6 per cent typical, and the control scheme supports a 1000 to 1 dimming range through the adjustment pin.

Order code and package

TPS92511DDARActive, HSOP-8 with exposed pad, 2500 pieces on a large reel, SN finish, MSL-3-260C-168 HR
TPS92511DDAActive, the same body, 95 pieces in a tube
Marking92511
Temperature rangeminus 40 to 125 degrees junction
Thermal resistance59.9 degrees per watt junction to ambient

Electrical parameters that decide the application

Input voltage4.5 V to 65 V
LED currentup to 0.5 A, set by a resistor
Current accuracyplus or minus 3.6 per cent typical
Switching frequency50 kHz to 500 kHz, set by a resistor
Dimming range1000 to 1 through the adjustment pin
External componentsfive, including the inductor and the diode
Sense resistornot required
Compensationinternal, no external network

Family variants and how they differ

Low side switchintegrated N channel MOSFET, the inductor current is sensed through it
Adjustment pinsets the current and provides analog dimming and thermal foldback
Diodeexternal, has to be rated for the full input voltage
Inductorexternal, chosen for the ripple at the set frequency
Padexposed thermal pad on the underside of the HSOP body

Points to check before this part goes on a BOM

Removing the sense resistor removes its loss and its tolerance. A 0.5 A string with a 200 mV sense resistor burns 100 mW in the resistor and adds its temperature coefficient to the current error. Sensing through the low side switch instead removes both, and it is the reason the part needs only five external components around it.

The control loop is proprietary and it does not sense the LED current directly. It regulates the inductor current, which follows the LED current in a buck converter. That is what makes the external compensation unnecessary, and it also means the accuracy figure is a system figure rather than a resistor tolerance.

65 V input covers a 48 V rail with room for a transient. Architectural and industrial lighting often runs from a 48 V bus, and a string of a dozen LEDs sits comfortably below it. The headroom for a transient and the margin for the switch node ringing are what the 65 V rating provides.

50 kHz to 500 kHz is a wide range for a reason. Low frequency favours efficiency and allows a larger inductor; high frequency allows a smaller inductor and a smaller board. A 1000 to 1 dimming range needs the loop to behave at very low currents, and the frequency choice affects how deep the dimming can go before the pulses become visible.

3.6 per cent typical is not a maximum. The typical figure is what most units do, and the spread over temperature and unit to unit is wider. In a multi fixture installation that spread is visible as a brightness difference between luminaires, so the number to quote to a lighting customer is the worst case, not the typical.

Thermal foldback through the adjustment pin is a lighting requirement, not an extra. A luminaire in a sealed enclosure will heat up, and reducing the current as the case temperature rises keeps the LEDs inside their rating. The pin accepts an analog voltage, so a thermistor network or a controller can drive it without any digital interface.

MSL-3 with 168 hours is the handling constraint on the reel. The HSOP body with an exposed pad needs a bake after that exposure. For a lighting producer running long batches this is a line planning item, and a tube of 95 pieces for prototypes avoids opening a 2500 piece reel for five boards.

The diode is the part that fails first at 65 V. It has to be rated for the input voltage plus the ringing on the switch node, and its reverse recovery affects the switching loss. A 100 V Schottky is the usual choice on a 48 V bus, and a 60 V part is not enough once the ringing is counted.

A five component solution is the selling point and the trap. What is left are the parts that decide the behaviour: the inductor, the diode, the input capacitor and the setting resistors. A cheap inductor with high resistance and a slow diode meets the count and misses the efficiency, and the customer sees the light output rather than the bill of material.

1000 to 1 dimming needs the frequency and the inductor to agree. At the bottom of the range the on time becomes short, and a low switching frequency with a large inductor cannot deliver a short enough pulse. The deep range is achievable, and only with the operating point chosen for it.

The string voltage has to stay below the input at every condition. It is a buck converter, so a string that needs more voltage than the rail will not light. The 65 V figure is the input ceiling and not the output capability, and a 60 V string on a 48 V rail is asking for a boost converter.

The exposed pad carries the switch heat and the diode carries the rest. At 0.5 A the conduction loss is small, and the diode loss sits outside the part. On a 48 V to 15 V conversion the diode is usually the warmer of the two, which is why its rating and its thermal path get as much attention as the switch.

The adjustment pin is both the current setting and the dimming input. One node does both, so the resistor sets the maximum current and the voltage on the same pin reduces it. A controller that drives the pin has to know the resistor value, because the same voltage means different currents in different fixtures.

Where a 65 V constant current buck fits

Architectural and industrial luminaires running from a 48 V bus, where the string voltage is a large fraction of the input and a linear driver would dissipate too much.

Fixtures that need deep dimming with a simple analog control, where the adjustment pin accepts a voltage from a controller or a thermistor network.

Where this order code fits

It drives an LED string from a 48 V rail in architectural and industrial lighting, regulating the current without a sense resistor or a compensation network. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does it really need no sense resistor? No sense resistor is required. The inductor current is sensed through the integrated low side switch, so the current is set by a resistor on the adjustment pin and not by a power resistor in the string.

What sets the LED current? A resistor on the adjustment pin, with the analog voltage on the same pin providing dimming. The current accuracy is 3.6 per cent typical, and the dimming range is 1000 to 1.

Can it drive a string above 48 V? The input is rated to 65 V, and the output has to stay below the input because it is a buck converter. A string close to the input voltage leaves little headroom for the current regulation, so the margin is part of the choice.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.