Contact Us

CD4511BE

Brand: Texas Instruments
Texas Instruments CD4511BE is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

CD4511BE — Power Management & Signal Chain | Superb Automation

CD4511BE

Texas Instruments — Power Management & Signal Chain

Product Overview

The CD4511BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

CD4511BE: the BCD to seven segment latch decoder driver in a plastic DIP

The CD4511BE is the plastic dual in line entry for the CD4511B, a BCD to seven segment latch decoder driver built from CMOS logic and n-p-n bipolar output devices on one die, in a 16-lead body. The vendor page lists the device as ACTIVE with one channel, a maximum supply current of 3000 microamps and an operating range of minus 55 to plus 125 degrees. The tube row is 25 pieces with a nickel palladium gold finish, and the marking is CD4511BE.

The output stage is the reason this part is still used. The vendor states a sourcing capability of up to 25 mA, which is enough to drive a common cathode light emitting display directly, and the logic side is CMOS with the low quiescent current that implies. Input latches store the BCD code, a lamp test input turns all segments on, a blanking input shuts the display off or modulates it, and codes above 1001 blank the outputs rather than showing a wrong digit.

The CD4511B rows as the addendum publishes them

Part classBCD to seven segment latch decoder driver
Vendor descriptorBCD to 7-segment latch decoder driver, 25 mA source
Vendor statusACTIVE, catalogue rating
Data sheetSCHS097 or later revision, acquired from Harris Semiconductor
Package addendum date18 September 2026
Supply range3 V to 18 V, 20 V type rating in the headline
Output source currentUp to 25 mA per segment
Supply current3000 microamps maximum
LatchInput latches store the BCD code
Test inputsLamp test and blanking
Invalid codesOutputs blanked for BCD codes above 1001
Input current1 microamp at 18 V over temperature, 100 nA at 25 degrees
PDIP body16 leads, 181.42 square millimetres, 19.3 by 9.4 mm
PDIP rowsCD4511BE, CD4511BE.A and CD4511BEE4, 25 pieces, Active
SOIC bodyNot offered, the family has no D body
SOP reel rowCD4511BNSR, 2000 pieces, Active
TSSOP tube rowCD4511BPW, Obsolete, blank quantity, Call TI
TSSOP reel rowCD4511BPWR, 2000 pieces, Active
Ceramic rowsCD4511BF and CD4511BF3A, 25 pieces, Active
Family companionCD40110B up down counter with the same display drive
Body areasPDIP 181.42, SOP 79.56 and TSSOP 32 square millimetres

The missing SOIC body is the first thing to check on this device. There is no wide small outline row, so the surface mount formats are the SOP at 2000 pieces and the TSSOP at 2000 pieces, and the TSSOP tube is closed. A board that was laid out for a 16-lead SOIC has to change footprint, and a board that was laid out for the SOP can stay. The ceramic side is fully active, which matters for a display that has to work at the temperature extremes.

What the output stage can drive

Twenty five milliamps per segment is a real number and it has a condition attached. The vendor states the sourcing capability as up to 25 mA, and at that current the output saturation voltage rises, so the segment current in a real display is set by a series resistor rather than by the driver alone. A common cathode display with a 2 V forward voltage on a 5 V rail and a 220 ohm resistor per segment draws about 13 mA, which is inside the rating and leaves margin for the saturation drop.

The blanking input does two jobs. It shuts the display off, and by pulse width modulating it, it dims the display. The lamp test input turns every segment on, which is the first test a production line runs because it catches an open segment without needing a known code. The latch holds the last BCD code while new data is presented, so a multiplexed display can share one driver across several digits and update them without flicker.

The supply current of 3000 microamps maximum is high for CMOS because the output stage is bipolar. With all seven segments on and sourcing 13 mA each, the total current is set by the display rather than by the logic, and the package thermal limit becomes the constraint. The plastic DIP at 181.42 square millimetres spreads that heat better than the TSSOP at 32, which is the reason a display driver is often the last part on a board to move to a small package.

Where the plastic DIP is the right choice

A display driver is a part that gets replaced. A segment short, a miswired display or a field surge takes the driver with it, and a socketed plastic DIP turns a board replacement into a component swap. That is why the DIP is still common in instruments and in panel meters even when the rest of the board is surface mount. The 25 piece tube is the packing that keeps a spare on the shelf.

For a sealed module the SOP at 79.56 square millimetres is the body that matches the display footprint and still has a 1.27 mm pitch. The TSSOP at 32 square millimetres is the smallest option and it is the one that needs the closest look at thermal margin when all segments are lit. A board that drives a large display at full brightness should not take the smallest body without a thermal check.

Multiplexing changes the current budget. When four digits share one driver, each digit is on for a quarter of the time and the segment current has to be raised to keep the average brightness, which pushes the output stage towards its 25 mA limit. The blanking input is the pin that does the multiplexing, and the latch holds the code for the digit that is currently on. A board that multiplexes eight digits has an on time of one eighth and a peak current that may exceed the driver rating, which is the case where a transistor per digit is cheaper than a bigger driver.

The series resistors are part of the driver, not an accessory. Their value sets the segment current, their tolerance sets the brightness match between segments, and their package sets the heat. A display that looks uneven is usually a resistor tolerance problem rather than a driver problem, and a display that dims as more segments light is a supply or a thermal problem rather than a logic problem, which is where the first hour of fault finding usually goes on a panel meter during a production run.

What the documents do not publish

The page does not print the segment output saturation voltage, the blanking frequency limit or the latch setup and hold times. Those are in the data sheet, and for a multiplexed display the blanking limit sets the refresh rate and therefore the visible flicker. The page also does not print the pin out, and for a 16-lead driver with seven segment outputs the pin out is what an assembly drawing needs.

Second source and long term availability

The vendor states that the CD4511B is similar to the MC14511, which is the cross reference most often used. Similar is not identical, and the output current and the blanking behaviour have to be checked before a substitution is released. The obsolete part cross reference hub collects those checks, and the supplier quality audit page covers how a new source is qualified for a display driver.

What to send with an enquiry

Send the string, the body, the display type and the segment current you intend to run. The current decides whether the driver is inside its rating, and the display type decides whether the common cathode output is the right polarity. If the board is surface mount, confirm the SOP footprint, because there is no SOIC body for this device. The kitting service page explains how display drivers, resistors and connectors are picked together for a build.