DRV8824PWPR
Product Specifications
DRV8824PWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV8824PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV8824PWPR: the 1.6 A stepper driver with a 32 step indexer
The DRV8824PWPR is a bipolar stepper motor driver in a 28 pin HTSSOP, supplied 2000 pieces on a large tape and reel. The vendor carries the part as ACTIVE and lists two H-bridges with a microstepping indexer that goes from full step to one thirty second step, a step and direction interface, configurable slow, fast and mixed decay, a continuous output current of 1.6 A per bridge, an operating supply of 8.2 to 45 V, a low power sleep mode, and protection against overcurrent, short circuit, undervoltage and overtemperature with a fault pin. Two bodies are offered, the 28 pin HTSSOP and a 28 pin VQFN at 5.00 by 5.00 millimetres.
The thirty second step mode is the feature that separates this part from the eighth step family on the same catalogue shelf. A mechanism that has to move in fine increments without a gearbox needs the finer indexer, and the indexer is inside the driver rather than in the controller. The trade is the current: 1.6 A against 1.9 or 2.5 A on the coarser parts, so a mechanism that needs both fine steps and high torque has to look at the next size up.
The DRV8824PWPR rows as the addendum publishes them
| Part class | Bipolar stepper driver with a 32 step indexer |
| Vendor status | ACTIVE, production data |
| Data sheet | SLVSA06K, October 2009, revised January 2022 |
| Supply range | 8.2 V to 45 V |
| Continuous current | 1.6 A per bridge |
| Microstepping | Full step to one thirty second step |
| Chopping gain | Factor of 5 on the sense voltage |
| Reference input range | 1 V to 3.5 V, operational below 1 V with reduced accuracy |
| Trip voltage | 660 mV typical at 3.3 V reference, 635 to 685 mV |
| Trip accuracy, 71 to 100 per cent | 5 per cent |
| Trip accuracy, 10 to 34 per cent | 15 per cent |
| Overcurrent trip | 1.8 A minimum, 5 A maximum |
| Overcurrent deglitch | 3 microseconds |
| Thermal shutdown | 150 to 180 degrees, 160 typical |
| Undervoltage lockout | 7.8 V to 8.2 V rising |
| Step frequency | 175 kHz maximum |
| Step pulse width | 2.8 microseconds minimum high |
| Thermal, HTSSOP | 38.9 degrees per watt junction to ambient |
| Thermal, VQFN | 35.8 degrees per watt junction to ambient |
| ESD | 2000 V human body, 500 V charged device |
| Body, HTSSOP | 28 pins, 9.70 by 6.40 millimetres |
| Reel row, HTSSOP | DRV8824PWPR, 2000 pieces, large tape and reel |
| Reel row, VQFN | DRV8824RHDR, 3000 pieces, large tape and reel |
| Small reel, VQFN | DRV8824RHDT, Obsolete |
| Moisture level | Level 2 at 260 degrees, one year floor life |
| Temperature | Minus 40 to plus 85 degrees |
The VQFN small reel row is obsolete while the large reel and the HTSSOP rows are live, so a prototype that arrives in a small reel today may not arrive that way next year. The moisture level is 2 rather than the level 3 of the eighth step family, which is one of the few specification differences that is not about current or resolution and does matter on a line that leaves a reel open.
What the electrical table fixes
The chopping current is the reference divided by five times the sense resistor, and the vendor's own example is 3.3 V with 0.5 ohm giving 1.32 A. That is below the 1.6 A rating, so a customer who wants the full rating needs 0.4 ohm, which gives 1.65 A and is just outside. The practical answer is 0.43 ohm for 1.53 A, and that is the kind of arithmetic that decides the resistor before the price is discussed. The 660 millivolt trip voltage and the 5 volt per volt gain are two statements of the same comparator.
The reference range starts at 1 V for full accuracy. Below 1 V the part still works but the accuracy degrades, which matters because a microstepping driver scales the reference internally for each step and the low steps are exactly where the scaling is smallest. A customer who sets the reference to 0.5 V to get a low current has put the accuracy band at its worst point and will see position error between microsteps.
The 45 V maximum is high for this family and makes the part usable on a 36 V rail with margin and on a 42 V automotive style rail. The undervoltage lockout at 7.8 to 8.2 V is above the bottom of the 8.2 V operating range, which is a common arrangement and means a supply that sags through 8 V turns the bridge off rather than running it at a low voltage. The overcurrent trip window of 1.8 to 5 A is wide, and it is a fault limit rather than a current control.
Where the body fits on a board
The 28 pin HTSSOP at 9.70 by 6.40 millimetres and the VQFN at 5.00 by 5.00 millimetres carry the same die in two thermal envelopes, and the QFN is the better of the two on paper at 35.8 degrees per watt against 38.9. The QFN wins only if the pad is soldered to a plane with vias, and a QFN on a two layer board with a thin ground is worse than the HTSSOP. The choice is a board stack up question, not a package question.
The sense resistors and the decay components are the tuning elements, and they sit close to the package because the chopping loop is short. A customer who mounts them on the far side of a connector gets a driver that works at low current and misbehaves at high current, and the fault presents as an overcurrent trip rather than as a tuning problem. The vendor's application section gives the component relationships rather than fixed values, which is a hint that they are meant to be tuned for the motor.
What the documents do not publish
The page gives the current and the resolution but no curve of current against ambient, and no microstep linearity figure. For a positioning system the linearity is the number that decides whether the mechanism can hold a position without a sensor, and it is in the typical characteristics rather than in the summary. The page also gives no output current waveform, so the shape of the microstep has to be measured.
The document does not print the register or pin strapping for the decay mode on the product page, only in the pin functions and the application section. A board that straps the decay pins for one motor and then changes the motor has to change the strapping, and the symptom is a hum rather than a fault. That is the sort of detail a customer discovers at the bench and not from a catalogue.
Second source and long term availability
A stepper driver with a 32 step indexer and a step and direction interface is available from a few vendors and the pin out is not standard, so a cross is a board change. The indexer resolution and the current setting are the two items to match first. The pin to pin cross reference page sets out the comparison, and the how to verify a drop in replacement page covers the bench work.
Both bodies have live large reel rows and the QFN small reel is closed, which is a sign that the vendor is packing for production. The document is in its eleventh revision and the part has been in production since 2009, so the die is mature. A ten year programme should still ask for a written statement rather than read a status column.
What to send with an enquiry
Send the exact string, the body, the quantity and the date. State the winding current and the sense resistor, because the chopping current is the reference divided by five times the resistor. State the supply rail, since the 45 V rating is what puts this part on a 36 V or 42 V rail rather than a 24 V one.
Say whether the mechanism needs the thirty second step or whether an eighth step would do, because the eighth step family carries more current on a comparable footprint. The BOM scrubbing page explains how we reconcile a line like this against the build before a schedule is confirmed.