Contact Us

DRV8811PWPR

Brand: Texas Instruments
Texas Instruments DRV8811PWPR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8811PWPR — Power Management & Signal Chain | Superb Automation

DRV8811PWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8811PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8811PWPR: the 1.9 A stepper driver with an eighth step indexer

The DRV8811PWPR is a microstepping stepper motor driver in a 28 pin HTSSOP, supplied 2000 pieces on a large tape and reel. The vendor carries the part as ACTIVE and lists a pulse width modulated microstepping indexer up to one eighth step, a step and direction interface, programmable mixed decay, blanking and off time, up to 1.9 A per winding, an on resistance of 1.0 ohm across the high and low side devices at 25 degrees, an operating supply of 8 to 38 V, and protection against undervoltage, overcurrent and thermal shutdown. The vendor states that it is pin to pin compatible with the DRV8818, which is the 2.5 A member of the same family.

Pin compatibility with a higher current part is the commercial argument for this device. A board can be drawn once and built with the 1.9 A part for a small mechanism and the 2.5 A part for a larger one, and only the current setting and the thermal copper change. A customer who expects a product line to grow should check which of the two the vendor intends to keep before committing the footprint, because the family has been in production since 2008 and the pin out has not moved since.

The DRV8811PWPR rows as the addendum publishes them

Part classBipolar stepper driver with an integrated microstepping indexer
Vendor statusACTIVE for the reel row, Obsolete for the tube row
Data sheetSLVS865J, September 2008, revised April 2017
Supply range8 V to 38 V
Current per windingUp to 1.9 A
On resistance, high plus low side1.0 ohm at 25 degrees
MicrosteppingFull, half, quarter and eighth step
Control interfaceStep and direction, with a home output
Decay controlProgrammable mixed decay, blanking and off time
CompatibilityPin to pin with the DRV8818
ProtectionUndervoltage lockout, overcurrent, thermal shutdown
BodyHTSSOP, 28 pins
Reel rowDRV8811PWPR, 2000 pieces, large tape and reel
G4 reel rowDRV8811PWPRG4, 2000 pieces, green material
Tube rowDRV8811PWP, Obsolete, blank quantity
MarkingDRV8811 on the body
Moisture levelLevel 3 at 260 degrees, 168 hour floor life
TemperatureMinus 40 to plus 85 degrees

The green material suffix is a separate row at the same reel size and the same price band in most catalogues, and it exists because some customers still carry a leaded material requirement into a new build. A customer who specifies the G4 string and a customer who specifies the plain string receive the same die in the same body, and the difference shows up in a material declaration rather than on the board.

What the electrical table fixes

The 1.0 ohm on resistance is high compared with the 0.37 ohm of the 2.5 A sibling, and at 1.9 A the bridge drops 1.9 V and dissipates 3.6 W. That is why the part is a 1.9 A device in a 28 pin package with a pad rather than a 2.5 A device, and why the current setting on the sense resistor is usually below the rating. A customer who sets the chopping current at the full 1.9 A on all four phases of a two phase stepper is running the die at its thermal edge in a warm enclosure.

The eighth step indexer is built in, so the controller only has to send step pulses and a direction, which is a real saving on a small controller. The decay mode, the blanking time and the off time are set by external components, which means a board can be tuned for a motor without a software change, and a board that is tuned for one motor may not drive another without moving those components. The vendor's application section gives the relationships rather than fixed values.

The 8 V minimum supply is the same constraint as the rest of the family, and the 38 V maximum is two volts above the 36 V family parts. A 24 V industrial rail is comfortable, a 36 V rail is inside, and a 48 V rail is not. A customer who has standardised on 48 V for a machine needs a different driver rather than a divider.

Where the body fits on a board

The 28 pin HTSSOP carries two H-bridges and their sense paths, and the exposed pad is the only thermal path that matters at 3.6 W. A board with a plane under the pad and a via array will hold the die near ambient, and a board with the pad on a thin trace will not. The pin to pin compatibility with the 2.5 A part means the copper can be laid out once for the larger dissipation and the smaller part dropped in, which is the reason to draw the thermal copper for the bigger member.

The home output is a small feature that saves an input on the controller. A mechanism that needs a reference position can use the indexer's own home signal rather than a separate sensor in some cases, and a board that leaves the pin unconnected has given that up. The step and direction interface needs two controller pins per axis, which is the lowest pin count of any interface in this family. A stepper in a printer or a textile machine usually needs the microstep resolution more than it needs the peak current, which is why this part outsells its larger sibling in that market.

What the documents do not publish

The page gives the current per winding and the on resistance but no curve of current against ambient, and no junction to ambient figure in the summary. Those are in the thermal table and the typical characteristics. It also gives no microstep accuracy figure for the indexer, which is the number that decides whether a mechanism can hold a position without a sensor.

The document does not print the external component values for the decay and off time on the product page. A customer who is comparing two stepper drivers by reading feature lists will conclude they are equivalent and will discover the difference in the tuning. That is not a fault in the document, but it is a reason to ask for the application section before a choice is made.

Second source and long term availability

Stepper drivers with an integrated indexer and a step and direction interface are made by several vendors and the pin out is not standard, so a cross is a board change. The current setting and the decay network are the two items to recheck. The pin to pin cross reference page sets out the comparison, and the how to verify a drop in replacement page covers the bench work.

The part is in its tenth revision of the document and the tube row is already obsolete, which is the pattern across the family. The 2.5 A sibling is the safer long term bet on the same footprint, and a customer who needs a ten year supply should consider whether the smaller current is really required. That is a question the vendor can answer better than a catalogue can.

What to send with an enquiry

Send the exact string, the quantity and the date. State the winding current, the winding resistance and the supply voltage, because the chopping current and the thermal rise both depend on all three. State the microstep resolution you need, since the indexer stops at one eighth step and a customer who needs one sixteenth has read the sibling part.

Say whether the board will also build with the 2.5 A member, because that decides the copper and the sense resistor. A short enquiry is enough if the string, the winding current and the rail are all in it. The BOM scrubbing page explains how we reconcile a line like this against the build before a schedule is confirmed.