Contact Us

DP83848CVV-NOPB

Brand: Texas Instruments
Texas Instruments DP83848CVV-NOPB is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DP83848CVV-NOPB — Power Management & Signal Chain | Superb Automation

DP83848CVV-NOPB

Texas Instruments — Power Management & Signal Chain

Product Overview

The DP83848CVV-NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DP83848CVV-NOPB: the single port 10/100 Ethernet transceiver in the 48 pin LQFP

The DP83848CVV-NOPB is a single port 10/100 megabit Ethernet physical layer transceiver in a 48 pin LQFP, supplied 250 pieces in a JEDEC tray. The vendor carries the family as ACTIVE and lists an IEEE 802.3 encoder and decoder with 10BASE-T and 100BASE-TX transceivers and filters, a 3.3 V media access controller interface, auto MDIX, an integrated physical sub layer with adaptive equalisation and baseline wander compensation, error free operation to 150 metres, a configurable RMII revision 1.2 interface, a serial management interface, JTAG, a 25 MHz clock output, programmable light emitting diode outputs for link, speed, activity, duplex and collision, and a typical power below 270 milliwatts.

The temperature grade is the part of this string that decides where the device can be used. The C suffix is rated 0 to 70 degrees, the I suffix minus 40 to 85, and the YB suffix minus 40 to 125 in a different 48 pin body. The catalogue string on this page is the commercial grade in the LQFP, and a customer who reads the family temperature range and assumes industrial screening has read the wrong row.

The DP83848CVV-NOPB rows as the addendum publishes them

Part classSingle port 10/100 Ethernet physical layer transceiver
Vendor statusACTIVE, production data
Data sheetSNLS266E, May 2007, revised March 2015
Process3.3 V, 0.18 micrometre CMOS
Typical powerBelow 270 milliwatts
Interface optionsMII, RMII revision 1.2, SNI, all configurable
ManagementMDC and MDIO serial management interface
Auto negotiationIEEE 802.3 with parallel detection
Auto MDIX10 and 100 megabit
Cable lengthError free to 150 metres
Clock output25 MHz
Packet test10/100 megabit built in self test
JTAGIEEE 1149.1
BodyLQFP, 48 pins, marking DP83848VV
Tray row, commercialDP83848CVV/NOPB, 250 pieces, JEDEC tray
Reel row, commercialDP83848CVVX/NOPB, 1000 pieces, large tape and reel
Reel row, industrialDP83848IVVX/NOPB, 1000 pieces, minus 40 to 85 degrees
Reel row, extendedDP83848YBX/NOPB, 1000 pieces, minus 40 to 125 degrees
Commercial temperature0 to 70 degrees
Moisture levelLevel 3 at 260 degrees, 168 hour floor life
Lead finishNickel palladium gold on the reel rows

The packing column is the first thing a buyer should notice. The plain string that carries this page, DP83848CVV/NOPB, is published only as a 250 piece JEDEC tray, and the tape and reel row has an X in the string, DP83848CVVX/NOPB at 1000 pieces. A purchase order that asks for a reel of DP83848CVV-NOPB is asking for a packing that the vendor does not list, and the answer from a distributor will be either a tray or a substitution to the X string. That is a line item worth correcting before a build, not during one.

What the electrical table fixes

The 270 milliwatt typical figure is a whole device number at 3.3 V and it sets the supply choice. A linear regulator from a 5 V rail has to drop 1.7 V at about 82 milliamps, which is 140 milliwatts of heat in the regulator, more than the transceiver itself. A switching supply or a 3.3 V rail that already exists is the right answer, and the thermal question for this part is usually the regulator rather than the transceiver.

The 150 metre error free figure is longer than the 100 metre limit in the base standard, and it is a vendor measurement rather than a guaranteed specification. A cable that meets the standard at 100 metres works with margin, and a cable that was installed to a lower grade may not work at 150 even though the device will report a link. The physical layer is where marginal cable shows up first, and the diagnostic registers that count errors are the ones to read when a link drops at length.

The interface options are configuration strapping rather than software, which means a board that sets RMII by a pull resistor cannot be changed to MII without a rework. The RMII revision 1.2 option reduces the pin count between the controller and the transceiver from about fifteen to about nine, and it is the reason this part survives in products with small controllers. A customer who is moving a board from MII to RMII has to check the clocking, because RMII needs a 50 MHz reference and MII does not.

Where the body fits on a board

The 48 pin LQFP in the 7.00 by 7.00 millimetre body is the industrial and extended grade package, and the C and I grades use the same 48 pin LQFP without the exposed pad of the HLQFP. A board that was drawn for the HLQFP land pattern will not accept the LQFP part, and the two bodies are the same pin count, which makes the mistake easy to make and expensive to find. The part number letter after the four digits is the only clue in the string.

The magnetics and the termination network take more board area than the transceiver, and the 150 metre capability depends on them as much as on the die. A customer who has chosen the part but not the magnetics module has not finished the Ethernet section, and the transformer turns ratio and the common mode choke are the two items that most often get carried over from an older board without a check.

What the documents do not publish

The page gives the family temperature range in the feature list but the ranges belong to different suffixes, and it does not print the junction to ambient thermal resistance in the summary, only in the thermal table of the full document. It gives no power figure at the industrial or extended grade, only the typical at the commercial one. For a board that has to survive 85 degrees in a cabinet, the derating has to come from the tables rather than from the headline.

A customer who needs the full register set should ask for the current revision of the document rather than the one attached to an old drawing package. The status of the extended temperature part is worth checking separately. The YB string is a different body and a different die screening, and its rows are older than the C rows on the same addendum. A customer who needs minus 40 to 125 degrees should not assume the C string will be screened to it because the family description mentions that range.

Second source and long term availability

Single port 10/100 transceivers are available from several vendors and the register model is close to the standard, but the strapping options and the RMII clocking differ, so a cross is a board check rather than a part swap. The pin to pin cross reference page sets out what we compare, and the how to verify a drop in replacement page covers the bench checks.

The document is from 2015 in its current revision and the addendum rows are current, so the family is still supplied. A 48 pin LQFP transceiver with a 0 to 70 degree rating is a mature part, and the risk is not availability but grade confusion, since four suffixes share one document and one pin count with two different bodies.

What to send with an enquiry

Send the exact string, the temperature grade, the packing and the quantity. State whether the interface is MII, RMII or SNI, because the strapping resistors are set on the board and a part cannot be reconfigured after assembly. State the controller part number, since the RMII reference clock is shared and the two have to agree.

If the board was qualified on a tray and a reel is now needed, say so, because the string changes to the X suffix and the price changes with it. The BOM scrubbing page explains how we reconcile a line like this against a build quantity before a schedule is confirmed.