TPS7B8733QKVURQ1
Product Specifications
TPS7B8733QKVURQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS7B8733QKVURQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS7B8733QKVURQ1: 3.3 V at 500 mA with power good in a TO-252
The TPS7B8733QKVURQ1 is the 3.3 V fixed member of the TPS7B87-Q1 line, a 500 mA automotive regulator with a 3 V to 40 V input window, 42 V of transient tolerance and 17 uA of quiescent current at light load. The KVU suffix is the five pin TO-252 body, where the tab is soldered to a copper island and carries most of the heat. Accuracy is plus or minus 0.85 percent over line, load and temperature, and the power-good output has a fixed threshold with a delay that is set by a capacitor.
The 87 branch is the fixed voltage branch: 3.3 V and 5 V only, no divider. The adjustable branch of the same family covers 1.2 V to 18 V. That split matters at the purchasing desk, because the two branches share a body and a pin count but not a bill of materials, and an order code that names the wrong one costs a build cycle. Dropout is 400 mV at 315 mA, 525 mV at 450 mA and 575 mV at the full 500 mA into a 3.3 V rail.
Key electrical data for the 3.3 V part
| Input range | 3 V to 40 V, 42 V maximum, with load dump tolerance through a series diode or clamp |
| Output | 3.3 V fixed at plus or minus 0.85 percent over line, load and temperature |
| Output current | 500 mA, current limit 540 mA to 780 mA brickwall |
| Quiescent current | 17 uA typical at light load, which keeps a parked module connected |
| Dropout | 400 mV at 315 mA, 525 mV at 450 mA, 575 mV at 500 mA |
| Power good | open drain with a fixed threshold, 2 percent of hysteresis and a DELAY pin |
| Protection | current limit, thermal shutdown and reverse current blocking |
Package, marking and reel data
| Body | TO-252 KVU, 5 pins, exposed tab soldered to the board |
| Reel | 2500 pieces, large tape and reel |
| Finish and moisture | SN, level 3, 260 C peak reflow, 168 hour floor life |
| Marking | 7B8733 |
| Companion body | the same die ships in the HSOIC DDA body with a different thermal path |
Where a 500 mA 3.3 V rail is used
Cameras, radar sensor heads, gateways and body modules in a vehicle all run a 3.3 V domain of a few hundred milliamps from the battery rail. The TO-252 tab is what makes a linear part viable there: at 500 mA from 13.5 V into 3.3 V the part burns 5.1 W, which no small body survives, so the honest use is either a lower input or a switching stage in front with this part as the quiet final stage.
At 9 V in the same 500 mA burns 2.85 W, and the TO-252 tab at 2.5 C per W junction to case passes that into a copper island at a manageable rise. The power-good output is the second reason to pick this part: a camera or a sensor head should not start capturing before its 3.3 V rail is in regulation, and a PG delay tied to a capacitor is a cheaper answer than a supervisor plus a timer. The same argument applies to the DELAY value: a long delay hides a slow rise of the input, and a short one lets the processor start before the rail has settled. The capacitor is a ceramic of a few nanofarads for a millisecond and a few microfarads for a second, and the data sheet prints the curve for both, at 25 C and at the cold end.
Buyer questions on the TPS7B8733QKVURQ1
How does this differ from the 5 V member at 500 mA? Only the factory trim. The die, the body, the pin out and the reel are the same, and the dropout figures shift with the output voltage. Two codes, one qualification, which is why the pair is used on boards that serve several sensor types.
Is the power-good threshold adjustable? No, it is fixed internally with 2 percent of hysteresis. The DELAY pin sets when the flag is released after the rail is in regulation, not the threshold itself.
What is the floor life on this part? Level 3, 168 hours at 260 C peak. A reel that has been open for longer than that has to be baked before reflow, and the label on the reel carries the date code that the incoming check reads.
Buying this regulator through a component supplier
Two voltage codes on one die is the easiest substitution mistake in a component store, so the label and the marking are both worth reading. Our date code management page covers the floor life rule on a level 3 part. For the thermal comparison between the TO-252 and the HSOIC bodies, power management cross reference prints both.