TPS16410DRCR
Product Specifications
TPS16410DRCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS16410DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS16410DRCR 40 V 1.8 A power limiting eFuse with input to output short detection in the 10 pin VSON body
The TPS16410DRCR is an integrated eFuse that limits power rather than current, which is the distinction that matters in a household appliance. It holds the output at a 15 W ceiling with five per cent accuracy, tolerates 4.5 to 40 V at the input, and detects a short from input to output, reporting it on a fault pin. The body is a 3 by 3 mm VSON with an exposed pad, and the on resistance is 152 milliohms typical, which is low enough that the part does not need a heatsink at the currents it is rated for.
The power limit is what makes the part interesting for appliances that have to meet IEC 60335 or UL 60730. Those standards care about the energy a fault can deliver into a load, not only about the current, so a switch that limits power to 15 W protects a motor winding or a heater element in a way that a plain current limit cannot. The part also offers a configurable blanking time, so a short overload that a motor draws at start up is ignored while a sustained fault is cut off, which is the behaviour a refrigerator compressor or a valve actuator actually needs.
Key parameters taken from the TPS16410DRCR document
| Input range | 4.5 to 40 V for the power limiting members of the family, tolerant of minus 1 V at the output |
| On resistance | 152 milliohms typical, 96 milliohms minimum and 260 milliohms maximum over minus 40 to plus 125 C junction, falling to 215 milliohms maximum between 0 and 85 C |
| Power limit | 2 W to 64 W programmable, with 12.94 to 14.44 W at a 255 kOhm resistor and 3 to 4.5 W at 26.7 kOhm, and plus or minus 5 per cent accuracy at 15 W |
| Current limit | 0.03 A to 1.8 A on the current limiting members, with 0.918 to 1.035 A at 5.49 kOhm and 1.671 to 1.881 A at 10 kOhm |
| Short detection | Input to output short detection with indication on the fault pin, present on every member of the family |
| Overvoltage protection | Rising threshold 1.48 to 1.58 V on the OVP pin, falling threshold 1.34 to 1.46 V, with the pin grounded to disable the function |
| Supply current | 1.2 mA typical and 2.1 mA maximum in operation, 14 to 36 microamps in shutdown |
| Current monitor | 45 to 55 microamps per amp of output current, with plus or minus 0.8 microamp of offset |
| Overcurrent set point | 2.11 to 2.35 A at a 7.32 kOhm resistor on the IOCP pin |
| Protection | Overtemperature shutdown, configurable blanking time for transient overloads, adjustable output slew rate on the dVdT pin |
| Certification | UL 2367 recognition file E169910 and IEC 62368-1 CB certification |
| Thermal | Junction to ambient 43.7 C per watt in the 10 pin DRC body with the exposed pad on a JEDEC board |
| Temperature | Minus 40 to plus 125 C junction |
| Body | VSON 10 pins, 3 by 3 mm, 0.5 mm pitch |
| Order code facts | TPS16410DRCR, VSON DRC 10 pins, 3000 pieces on a large reel, NIPDAU finish, moisture level 2 with a one year floor life, minus 40 to plus 125 C |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
The on resistance window is wide and the maximum is what has to be used in a thermal calculation. At 152 milliohms typical and 1.8 A the dissipation is about half a watt, and at the 260 milliohm maximum it is closer to 0.85 W, which on a 3 by 3 mm body with a 43.7 C per watt path is a 36 degree rise. That is fine at 25 C ambient and marginal inside a sealed appliance. The answer is copper under the exposed pad, and the board area around the part is part of the thermal solution rather than empty space.
The blanking time is set by a capacitor, and it is the feature that separates a product that survives a motor start from one that trips on every inrush. A compressor or a valve actuator draws several times its running current for a fraction of a second. A power limit with no blanking would cut the rail during that window. A capacitor on the delay pin holds the limit off long enough for the motor to come up, and the value is chosen against the measured inrush of the real load rather than from a rule of thumb.
The input to output short detection is a diagnostic that a plain fuse cannot give. When the pass element fails short, the load sees the full input rail with no protection at all, and the only sign is a fault that appears elsewhere. This part detects that condition and reports it on the fault pin, so a controller can shut the system down and log a code. On an appliance that is serviced rather than replaced, that code is the difference between a board swap and a diagnosis.
The current monitor output is a current, not a voltage, so the resistor to ground sets the scale. At 45 to 55 microamps per amp, a 10 kOhm resistor gives 0.45 to 0.55 V at 1 A, which suits a 3.3 V converter. That monitor is also what allows a controller to distinguish an overload from a short without a separate sense resistor, and it is accurate enough over the 0.3 to 0.8 A range to be used as a load measurement rather than only as a fault flag.
- Dissipation and junction temperature at the maximum on resistance and the maximum load current, on the real board.
- Blanking time against the measured inrush of the actual load, with the capacitor chosen from that measurement.
- Power limit accuracy at the production setting, since the five per cent figure is what the safety file claims.
- Short detection response, verified by shorting the output during a normal load and checking the fault pin.
- Current monitor scale over temperature, because a controller that reads the monitor for load measurement needs the drift.
- Overvoltage threshold with the divider fitted, since the pin window is narrow and a one per cent resistor moves it.
Which projects this part fits
This part fits refrigerator and freezer control boards, ovens and dishwashers, HVAC valve and actuator control, ventilators and anaesthesia delivery systems, and any appliance where a fault has to be limited in energy rather than only in current. It also fits backplane power protection in programmable logic controllers and distributed control systems, where the current limit is set by a resistor on the limit pin. Customers who need the same protection with a latched fault instead of an auto retry use the adjacent member of the family, which shares the body and the pinout.
Questions that come up before a purchase order is released
What is the difference between power limiting and current limiting?
A current limit caps the current, so the energy delivered into a fault depends on the load resistance and the input voltage. A power limit caps the product of voltage and current, so the energy is bounded regardless of the load. For a safety file that has to show a limited energy into any fault, the power limit is the simpler argument, and that is why the appliance standards push customers towards it.
Why does the part need a blanking capacitor?
Because real loads draw more than their steady current for a short time. Without blanking, a motor start or a lamp inrush trips the limit and the product resets. The capacitor holds the decision off for a window that the customer chooses, and the window has to be shorter than the time in which a real fault would damage something, which is why it is measured rather than assumed.
Can it replace a fuse?
Electrically yes, for the protection function, and it adds diagnostics that a fuse cannot give. It does not remove the need for a safety approved component in every standard, so the certification path has to be checked for the product. The part is UL 2367 recognised and IEC 62368-1 CB certified, which covers a large part of the work, but a household appliance file may still want a fuse in series for the disconnect function.
What does the fault pin drive?
It is an open drain output that can feed a controller input or drive an external P channel FET for a redundant disconnect. The second use matters in safety related products, where a single pass element is not considered enough and the fault signal has to remove the supply through a second device. The pin is asserted for a short, an overcurrent event and an overtemperature event, so the controller cannot tell them apart without the current monitor.
How is the part checked at incoming inspection?
Reel and moisture bag check, marking check, and a functional test on a board that applies a load, trips the limit and reads the fault pin. The on resistance can be checked with a four wire measurement at a known current on a sample, which catches a mixed lot. Because the part carries a safety certification, we keep the lot and date code record with the test result, so a later field question can be traced back.
How SUPERB handles this line
We supply the TPS16410DRCR from original reels with lot and date code traceability, and we check the moisture level on receipt because the DRC body is level 2 with a one year floor life rather than the unlimited level that some customers assume. The power management cross reference page lists the protection and hot swap families we carry, incoming inspection plan covers the test sequence for parts that carry a safety file, and pin to pin cross reference is the page to start from when a board has to move between members of the same family.