Contact Us

TPS62111RSAR

Brand: Texas Instruments
Texas Instruments TPS62111RSAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62111RSAR — Power Management & Signal Chain | Superb Automation

TPS62111RSAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62111RSAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62111RSAR: 17 V input, 1.5 A synchronous buck with 100 percent duty capability

TPS62111RSAR is a synchronous step-down converter that can hold its output when the input falls close to it in a QFN-16 body of 16 pins. It runs from 3.8 V to 17 V, produces an adjustable 1.2 V to 16 V or a fixed output at up to 1.5 A, switches at about 1 MHz, and can hold 100 percent duty so the output follows a falling input instead of dropping out.

Order code and package

Ordering stringTPS62111RSAR, RSA package, 3 mm by 3 mm QFN, tape and reel
Package16-pin QFN with PowerPAD, 3.00 mm by 3.00 mm
Output optionsAdjustable 1.2 V to 16 V, plus fixed versions in the same family
Ambient range-40 C to 85 C
Pin count checkVIN, SW, GND, FB, COMP, EN, SYNC, SS, LBI and LBO plus the pad

Electrical parameters that decide the application

Input range3.8 V to 17 V operating
Current1.5 A rated with the internal switches
Switching frequency1 MHz typical, synchronizable from 0.8 MHz to 1.4 MHz
Duty cycle100 percent maximum, which is the low dropout mode
Output range1.2 V to 16 V adjustable
Reference inductor6.8 microhenry in the data sheet application circuits

Points to check before this part goes on a BOM

The 100 percent duty capability is the feature that separates this part from a conventional buck. When a 12 V rail sags toward the output voltage the converter stops switching and passes the input through, so a 5 V output keeps regulating until the input falls to about 5 V plus the resistive drop of the switch and inductor. A part without that mode would drop out at 6 V and take the load down with it.

Seventeen volts in and 1.2 V out is a 7 percent duty cycle at 1 MHz, which is 70 ns of on time, and that is the corner where the minimum on time and the switch node rise time start to matter. The same part at 12 V in and 5 V out is a 42 percent duty cycle and is entirely comfortable, so the input voltage and the output voltage have to be considered together rather than separately.

The 6.8 microhenry inductor in the reference circuits is chosen for 1 MHz and roughly 1 A of ripple-free operation at the rated current. At 1.5 A the peak current is above the reference load, and the inductor saturation rating has to cover the current limit rather than the rated output, because the converter will reach the limit during a load step before it reaches thermal shutdown.

Synchronization runs from 0.8 MHz to 1.4 MHz, so an external clock outside that band will either be ignored or force the part outside its specification. A system that shares one clock across several converters has to include this one in the range check, and the SYNC pin must be tied to a defined level when it is not used.

The adjustable range tops out at 16 V from a 17 V input, which is a 94 percent duty cycle. In that corner the high-side switch is on almost continuously, the low-side switch barely conducts, and the current limit behaves differently from the low duty case. A 15 V output from a 17 V rail is the practical ceiling once the input tolerance is counted.

A 3 mm by 3 mm QFN at 1.5 A and 1 MHz dissipates a few hundred milliwatts, and the pad is the only path out. Boards that mount this part with thermal vias under the pad and copper on the reverse side run far cooler than boards that treat the pad as a mechanical feature, and the data sheet thermal numbers assume the former.

The LBI and LBO pins give a comparator with its own divider, so the host can be told that the input sag it is riding through is about to end instead of finding out when the output finally drops. Setting that divider against the same reference family keeps the warning consistent with the converter's own behaviour, and the alternative of watching the output means the warning always arrives late by the amount of output capacitance on the rail.

Where this order code fits

The usual fit is a 12 V or 15 V industrial rail, or a three-cell lithium pack, feeding a 3.3 V or 5 V rail at up to 1.5 A, especially where the input is allowed to sag and the load must not notice. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Does 100 percent duty mean it can pass the input straight through? Yes, with a resistive drop through the high-side switch and the inductor. That is how the part holds regulation during a supply sag, and it is also why the dropout voltage is a resistance figure rather than a fixed number.

Can the switching frequency be changed? Within 0.8 MHz to 1.4 MHz by an external clock, and around 1 MHz by the internal oscillator. Changing the frequency changes the inductor and compensation values, so it is a board change and not a resistor change.

Is a 17 V input safe for a 12 V automotive rail? No. Load dump on a 12 V vehicle rail goes far above 17 V, and this part is not an automotive grade device. A front-end clamp or a different family is required before the converter sees the rail.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.