Contact Us

TPS62560DRVR

Brand: Texas Instruments
Texas Instruments TPS62560DRVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62560DRVR — Power Management & Signal Chain | Superb Automation

TPS62560DRVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62560DRVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62560DRVR: 2.5 V to 5.5 V, 600 mA, 2.25 MHz synchronous step-down converter

TPS62560DRVR is a synchronous buck converter with an integrated high-side and low-side FET for single cell and 3.3 V portable rails in a SON (DRV) body of 6 pins. It takes 2.5 V to 5.5 V in, delivers 600 mA, switches at a fixed 2.25 MHz and drops its own quiescent current to around 15 microamp in power save mode, so the converter itself does not eat the battery it is supposed to extend.

Order code and package

Ordering stringTPS62560DRVR, DRV package, 2 mm by 2 mm SON, tape and reel
Family membersTPS62560 (adjustable, power save), TPS62561 (fixed PWM, 5-pin SOT), TPS62562 (fixed output)
Package6-pin SON, 2.00 mm by 2.00 mm by 0.80 mm
Ambient range-40 C to 85 C
Pin count checkVIN, SW, FB, EN, MODE and GND, all six used in a normal circuit
Assembly noteThe SON body has no visible leads, so the paste stencil and the reflow profile decide the joint, not the iron

Electrical parameters that decide the application

Input range2.5 V to 5.5 V, which covers one Li-Ion cell end to end and a regulated 3.3 V rail
Output current600 mA continuous
Switching frequency2.25 MHz fixed, so the inductor can be 2.2 microhenry
Reference600 mV, output accuracy plus or minus 2.5 percent in PWM mode
Quiescent current15 microamp typical, 18.5 microamp maximum, in power save mode without switching
Shutdown currentUnder 1 microamp with EN low
Switch resistance252 milliohm high side typical, 194 milliohm low side, at 3.6 V gate drive
Current limit1.0 A minimum, 1.2 A maximum forward limit on both FETs
Duty cycle100 percent, for the lowest possible dropout
Thermal shutdown140 C junction with 20 C hysteresis

Points to check before this part goes on a BOM

The 100 percent duty cycle mode is the reason this part holds a rail through a battery sag, and it is also the number to check first. In that mode only the high-side FET sits in the path, so the dropout at 600 mA is 151 mV with the typical 252 milliohm and 295 mV with the 492 milliohm worst case. A 3.3 V output from a single cell is therefore already out of reach at 3.6 V nominal before the cell is anywhere near empty, and a 3.0 V rail is the honest ceiling for the second half of the discharge curve.

At 2.25 MHz a 2.2 microhenry inductor carries about 180 mA of ripple at 3.6 V in and 1.8 V out, which is 30 percent of the rated load and the reason the data sheet can ask for a small 10 microfarad ceramic output capacitor. Halving the inductance doubles that ripple to 60 percent, which is still inside the current limit but starts to show as output ripple and as extra core loss in a small shielded part.

Standby arithmetic decides the chemistry. At 15 microamp the converter drains 131 mAh over a year, and at the 18.5 microamp maximum it drains 162 mAh, which is a measurable slice of a 200 mAh coin cell. Shutdown at 0.1 microamp is 0.9 mAh a year, three orders of magnitude lower, so a product that sleeps for months has to pull EN low rather than rely on the light-load mode.

MODE is not a spare pin. Tied to ground the part enters power save mode at light load and gives the 15 microamp figure, tied high it stays in fixed frequency PWM and the quiescent current rises to the milliamp region while the output ripple becomes predictable. A radio or an ADC on the same rail usually wants MODE high, and the efficiency curve in the data sheet is drawn for MODE low, so the two figures in a quotation are not the same operating point.

The TPS62561 is the same silicon in a 5-pin SOT package with fixed frequency operation only, and the TPS62562 replaces the feedback divider with an internal one. All three share the 600 mA rating, so a buying list that mixes them across builds will produce boards with the same current capability and different standby behaviour, which is exactly the kind of difference that only shows up in a battery life test.

The 2 mm by 2 mm SON has a thermal pad and almost no lead to inspect. The data sheet thermal numbers assume the pad is soldered to a copper area, and at 600 mA the conduction loss is roughly 45 mW in the high side and 35 mW in the low side at 50 percent duty, small enough that a modest pad is adequate, but a pad that is starved of paste will show up as a hot unit in a 60 C cabinet rather than as a dead one on the bench.

Where this order code fits

The usual fit is a point of load rail inside a handheld instrument, a portable media player, a GPS receiver or a battery powered sensor node, where a 3.3 V or 1.8 V rail has to come from one cell and the board has no room for a controller plus external FETs. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does it need an external compensation network? No. The control loop is internal and the data sheet typical application uses a 2.2 microhenry inductor with two ceramic capacitors, so there is nothing to tune for a first build.

Can the same footprint take the fixed output version? The TPS62562 is the fixed output member of the family in the same 6-pin SON, and the TPS62561 is the 5-pin SOT with fixed frequency only, so the board has to be laid out for one body style before the part is chosen.

What limits the load below 600 mA? Thermal rise in the SON and the 1.0 A current limit are both comfortable at 600 mA, so the practical limit is usually the inductor saturation current and the input capacitor ripple rating, not the silicon.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.