Contact Us

TPS53515ARVER

Brand: Texas Instruments
Texas Instruments TPS53515ARVER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS53515ARVER — Power Management & Signal Chain | Superb Automation

TPS53515ARVER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS53515ARVER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS53515ARVER: 12 A single synchronous buck with eight frequency settings

TPS53515ARVER is a 12 A synchronous step-down converter with integrated switches and D-CAP3 control in a VQFN-CLIP body of 28 pins. The input window is 1.5 V to 18 V with a 4.5 V to 25 V bias rail, the output runs 0.6 V to 5.5 V at 12 A, the reference is 600 mV at plus or minus 0.5 percent, and the switching frequency is selectable in eight steps from 250 kHz to 1 MHz.

Order code and package

Ordering stringTPS53515ARVER, RVE package, tape and reel
Package28-pin VQFN-CLIP, 3.50 mm by 4.50 mm
Ambient range-40 C to 85 C
Switch pair13.8 milliohm high side and 5.9 milliohm low side, integrated
FrequencyEight settings from 250 kHz to 1 MHz, chosen by a resistor

Electrical parameters that decide the application

Input range1.5 V to 18 V, with the bias rail from 4.5 V to 25 V
Output range0.6 V to 5.5 V
Output current12 A continuous
Reference600 mV, plus or minus 0.5 percent
ModesAuto-skip for light-load efficiency, or forced continuous for tight ripple
Start-upInternal soft start, capable of starting into a prebiased output
MonitoringOpen-drain power-good output

Points to check before this part goes on a BOM

The separate bias rail is what makes the low input range possible. With VDD fed from 5 V, the converter can work from an input as low as 1.5 V while still driving its own high-side gate, which is the case for a 3.3 V or 2.5 V bus that sags during a load step. Tie the bias to the input and the usable input range collapses to the 4.5 V end of the window.

Twelve amp through 13.8 and 5.9 milliohm is arithmetic with a sharp edge. Into 1 V from 12 V the duty cycle is 8.3 percent, so the high side carries 144 square amp times 13.8 milliohm for that share, about 0.17 W, and the low side carries the rest at 5.9 milliohm, about 0.78 W. That 0.95 W is the floor before switching and gate drive, and it has to leave through a 3.5 mm by 4.5 mm pad.

Eight frequency settings exist because one number cannot serve every board. At 250 kHz the on time at 18 V to 0.6 V is still short, the inductor is large and the efficiency at high current is good; at 1 MHz the inductor shrinks and the switching loss climbs. The frequency also decides whether the converter's ripple lands in a band a radio or an ADC cares about, so it is chosen with the load, not with the data sheet.

Forced continuous conduction keeps the ripple and the frequency fixed at light load, which is what a DSP or an FPGA rail needs, because those parts draw little current most of the time but cannot tolerate a rail that dips into a burst pattern. Auto-skip is the opposite trade: lower standby loss and a rail that pulses. The mode pin decides, and both modes are specified.

Prebiased start-up matters when the 0.6 V to 5.5 V output is a rail that another source holds up, such as a backup supply or a second converter in parallel. The part ramps into that state instead of pulling the rail to zero first, which avoids a glitch on a live bus. The internal soft start still controls the slew, so the inrush is bounded.

Temperature is specified to 85 C ambient, not 105 C. A 12 A converter in a sealed enclosure with no airflow will reach that ambient from its own 1 W, so the board copper and the enclosure are part of the current budget. If the application needs more, the frequency and the inductor are the two levers that move the loss without changing the part.

The integrated boost switch is what removes the external bootstrap diode, and it also keeps the high-side drive valid at the low duty cycles this part sees when a 12 V rail feeds a 0.6 V core. At 5 percent duty the high-side switch is on for 100 ns at 500 kHz, and the gate has to be charged and discharged inside that window. A weak drive at that duty turns the on-state loss into the dominant term, which is why the switch resistance figures alone do not predict the efficiency at the bottom of the output range.

Where this order code fits

It suits a point-of-load rail for a server, a switch or an optical module line card, where a 12 V or 5 V backplane feeds a 1 V to 1.8 V core at up to 12 A and the board is dense. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Do I need the separate bias supply? Only if the input can fall below 4.5 V. Above that, the bias pin can be tied to the input. Below it, the bias rail has to come from somewhere else, and the data sheet is explicit about the two ranges.

Is 12 A available at 85 C in still air? The 12 A is the switch and limit rating. Continuous current at 85 C ambient follows from about 1 W of conduction loss and the thermal resistance of the pad and copper, so a dense board with little copper under the part will not reach it.

Why does the reference matter at 0.5 percent? Because the output is 0.6 V at the bottom of the range. Half a percent of 600 mV is 3 mV, and at a 1 V output that is the whole DC error budget for a core rail that has to stay inside its window.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the OEM Procurement page sets out the checks that keep a substitute from failing on the bench.