TPS54824RNVR
Product Specifications
TPS54824RNVR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54824RNVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54824RNVR: 17 V input, 8 A synchronous buck in a 3.5 mm body
TPS54824RNVR is an 8 A synchronous step-down converter with peak current mode control in a HotRod QFN body of 18 pins. It works from 4.5 V to 17 V with 19 V as the absolute maximum, delivers 8 A from 0.6 V to 12 V, switches between 200 kHz and 1.6 MHz with external synchronisation, holds a 0.6 V reference at plus or minus 0.85 percent over temperature, and draws 3 microamp in shutdown.
Order code and package
| Ordering string | TPS54824RNVR, RNV package, tape and reel |
| Package | 18-pin HotRod QFN, 3.50 mm by 3.50 mm, no bond wires in the power path |
| Thermal resistance | 25 C/W junction to ambient in this package, revised down from 34 C/W |
| Ambient range | Junction -40 C to 150 C |
| Switch pair | 14.1 milliohm high side, 6.1 milliohm low side |
Electrical parameters that decide the application
| Input range | 4.5 V to 17 V operating, 19 V absolute maximum |
| Output range | 0.6 V to 12 V |
| Output current | 8 A continuous |
| Frequency | 200 kHz to 1.6 MHz, and it locks to an external clock |
| Reference | 0.6 V at plus or minus 0.85 percent over temperature |
| Shutdown current | 3 microamp |
| Protection | Hiccup current limit, output overvoltage, thermal shutdown without latch |
Points to check before this part goes on a BOM
The thermal number in this data sheet was revised from 34 C/W to 25 C/W, which is a reminder that package thermal figures change between revisions and that a board copied from an old printout may be more conservative than it needs to be, or the reverse. At 8 A into 1 V from 12 V the conduction loss is roughly 0.9 W, so 25 C/W puts the junction about 23 C above ambient, and 34 C/W puts it 32 C above. The difference is real in a sealed enclosure and it comes from the same silicon.
Synchronising to an external clock is what keeps a multi-rail board quiet. Four converters at slightly different free-running frequencies beat against each other and produce a low-frequency envelope that appears as noise in a receiver or as jitter in a converter. Locking all four to one clock, with phase spacing, removes the envelope. The cost is that the clock has to be present before the rail starts, so the sequencing order matters.
Peak current mode control brings a compensation network, and that is the difference between this part and the D-CAP parts nearby: it needs an external compensation network on the COMP pin, and in exchange it can be synchronised, it has a defined behaviour with a wide range of output capacitors, and it is stable with a feed-forward from the input. A board that has to work with an electrolytic output capacitor is a better fit here than with an internally compensated part.
Hiccup current limit protects the inductor and the switch during a hard short by shutting down and retrying rather than sitting at the limit. The fault energy is bounded to a small fraction of the limit power, which is why an 8 A converter can survive a probe slip on a bench. The recovery is automatic, so the supervisor sees repeated power-good drops rather than one event.
Adjustable input undervoltage lockout lets the enable divider set the point at which the converter starts, which is the tool for a 12 V rail that has to come up after a backplane has settled. Together with the soft-start and tracking pin, it lets this rail follow another rail rather than start on its own schedule, which is what a core rail and its input and output rails need.
Nineteen volt absolute maximum against a 17 V operating ceiling gives 2 V of margin, which is enough for a 12 V rail with normal transients and not enough for an automotive rail without a front-end clamp. The input capacitor sees that transient first, and its voltage rating has to be chosen against the transient, not against the 12 V nominal.
The HotRod package removes the bond wires from the current path, and the point is not marketing: bond wires add inductance in series with the switch, and that inductance rings with the switch capacitance at every transition. Removing it lowers the ringing, which lowers the snubber loss and the radiated field. On a board with several converters this is the difference between passing a conducted emissions limit with a small input filter and needing a large one.
Where this order code fits
It fits a telecom or server point-of-load rail, a test instrument supply, or a medical imaging board, where the input is 12 V, the current is up to 8 A, and several rails have to run from one clock. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Does it need an external compensation network? Yes. Peak current mode control here uses the COMP pin, so the network is part of the circuit and part of the stability. A board that has to avoid those components is a different part, not a different resistor value.
Can it run from a 19 V brick? 19 V is the absolute maximum, not an operating input. A 19 V brick at the top of its tolerance is over the ceiling, so the rail needs a front-end device or a part rated above 19 V.
What does the tracking pin actually track? The soft-start ramp can follow an external voltage, so this rail comes up in proportion to another rail instead of on a fixed timer. That is how two rails reach their setpoints together.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Obsolescence Management page sets out the checks that keep a substitute from failing on the bench.