INA129UA
Product Specifications
INA129UA
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA129UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA129UA: the A grade in a 75 piece tube, and the offset window that comes with the bin
The INA129UA is the A grade of the eight pin SOIC in a 75 piece tube, which is the buy for a first build or for a line that still loads from a tube feeder. The body is the same 4.9 by 6 mm SOIC and the gain network is the same 49.4 kΩ, so the gain equation is unchanged; the difference is the offset and drift window, which widens from 500 µV divided by gain to 1000 on this bin.
That widening is the whole reason the two rows exist. On a gain of 100 channel the UA bin is 10 µV maximum at the input against 5 on the U, and the drift moves from 0.5 to 1 µV per degree divided by gain. On a pressure transmitter with a 10 mV full scale the UA bin uses 0.1 per cent of the range for offset and the U bin 0.05, and both are trimmed at the bench; on an untrimmed channel the difference is the difference between a specification and a hope.
The INA129UA rows as the addendum publishes them
| Part class | Precision instrumentation amplifier, three op amp, current feedback input |
| Vendor status | Active, production |
| Data sheet | SBOS051G, revised January 2026 |
| Addendum row | INA129UA, 75 pieces per tube |
| Grade | A suffix, the wider offset and drift window |
| Gain equation | G = 1 + 49.4 kΩ divided by RG |
| Input offset voltage | 1000 µV divided by gain maximum on the UA bin, 10 µV at a gain of 100 |
| Offset drift | 1 µV per degree divided by gain maximum |
| Input bias current | 10 nA maximum on the UA rows, 2 nA typical |
| Voltage noise | 8 nV per root hertz at 1 kHz |
| Common mode rejection | 110 dB minimum at a gain of 100, 73 dB at unity gain |
| Bandwidth | 1.3 MHz at unity gain, 200 kHz at a gain of 100 |
| Supply range | Plus or minus 2.25 V to plus or minus 18 V |
| Quiescent current | 700 µA typical |
| Body | SOIC, D outline, 8 pins |
| Carrier | 75 pieces per tube |
| Moisture level | Level 3, 260 degrees, 168 hour floor life |
| Reel sibling | INA129UA/2K5, 2500 pieces |
| Temperature range | Minus 40 to plus 125 degrees |
Gain error rows, the A grade and the 0.024 per cent window
Gain error on this family is quoted per gain setting and per grade, and the tightest row is 0.024 per cent at a gain of 1 on the A grade parts. That figure is smaller than the tolerance of the resistor that sets the gain, so the resistor, not the amplifier, is what a calibration adjusts. At a gain of 100 the family rows widen and the A grade still holds a window about half as wide as the plain grade, which is the practical difference between the two bins on a channel that is calibrated once rather than per unit.
Nonlinearity is 0.001 per cent of full scale on the plain grade and 0.0005 per cent on the A grade, which is well below any converter this part is likely to drive. The number that limits a real channel is the gain drift, quoted in ppm per degree, because it cannot be trimmed at the bench and it moves with the cabinet temperature. On INA129UA the drift row is the one to put in a specification that has to hold over temperature, and the room temperature gain error row is the one to put in a production test limit.
50 µV of offset and half a microvolt per degree
The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA129UA can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.
The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.
Why the INA129 uses 49.4 kΩ and the INA128 uses 50 kΩ
The two parts in this document are the same silicon with one difference in the internal gain network: the INA128 uses 50 kΩ so that G = 1 + 50 kΩ divided by RG, and the INA129 uses 49.4 kΩ so that G = 1 + 49.4 kΩ divided by RG. The 49.4 kΩ is there so that a resistor value chosen for a competing part gives the same gain in the INA129, which is what makes it a drop-in replacement on an existing board without a resistor change. On a gain of 100 the difference between the two equations is 1.2 per cent, which is larger than the resistor tolerance and large enough to fail a calibrated channel.
Because of that, INA129UA must be bought as the part the board was drawn for, and the substitution question is not symmetrical. An INA129 in an INA128 socket runs 1.2 per cent low at a gain of 100 and 0.12 per cent low at a gain of 10, so it passes a functional test and fails a calibration. An INA128 in an INA129 socket runs high by the same amount. Neither failure is visible without a gain measurement, which is why the two codes should never be treated as interchangeable.
Tubes, reels and two different moisture levels
The SOIC rows ship 75 pieces in a tube or 2500 pieces on a large reel, and the DIP rows ship 50 pieces in a tube. The carrier decides the handling, not the part: a 75 piece tube is a prototype or a small build, and a 2500 piece reel is a production run that will take months to consume. Between those two there is nothing on the addendum, which is why a build of 500 boards is usually bought as several tubes and hand fed rather than as a partial reel.
The moisture level differs between the carriers on this family. The tube rows are published at level 2 with a one year floor life, and the reel rows at level 3 with a 168 hour floor life, so the same die has a different shop floor rule depending on how it arrived. A level 3 reel that is opened for a partial build has to go back into dry storage or be baked, and a 2500 piece reel can easily sit open across two builds. Reading the level off the label rather than off the part number is the practical control, and INA129UA is the code to check it against.
120 dB of common mode rejection and the source imbalance that removes it
The common mode rejection row is 120 dB minimum on the family, measured with a 1 kΩ source imbalance, and it is the number that decides whether a bridge channel can reject a 50 Hz disturbance. Rejection degrades with source imbalance at roughly 1 dB per 100 Ω above the test condition, so a channel with a 10 kΩ mismatch between the two input legs has thrown away most of the 120 dB. In practice that mismatch comes from the sensor rather than from the board: a 350 Ω bridge with one leg 5 Ω high, or a thermocouple with a 2 kΩ cable resistance on one side only.
The fix is a pair of matched resistors at the input, or a buffer for each leg, or a sensor with a trimmed output impedance. The REF pin is part of the same problem: the vendor notes that 8 Ω in series with REF is enough to degrade rejection on a typical part, so the reference has to be driven from a low impedance source such as an amplifier or a shunt reference with a capacitor, not from a divider alone. On INA129UA the rejection also falls with frequency, and the vendor curve of rejection against frequency is the one to read for a switching supply disturbance rather than the dc row.
The REF pin, the 8 Ω rule and single supply references
The REF pin sets the output level and is part of the signal path in a way that is easy to forget. Any resistance in series with it appears as a common mode error at the input and as a gain error at the output at the same time, and the vendor states that 8 Ω is enough to degrade common mode rejection on a typical part. A divider made of two 10 kΩ resistors has a source impedance of 5 kΩ, which is three orders of magnitude above that, so an unbuffered divider is not a reference for INA129UA at any gain.
On a bipolar supply the REF pin goes to ground, and ground has to be the same ground the converter uses or the difference appears as an offset. On a single supply the pin goes to a buffered mid rail, and the buffer has to be able to sink and source the current the REF pin draws, which is small but not zero. A shunt reference with a 1 µF capacitor is the cheap answer; an op amp buffer is the answer when the reference also has to drive other channels. Both are one more part than a divider and both are the reason a single supply channel measures what it claims.
Buying INA129UA
A 75 piece tube is the right quantity for a pilot build and the wrong one for a production line, and the crossover is roughly the point where the feeder change costs more than the reel premium. The tube also carries level 3 moisture, so the floor life clock starts when the tube is opened and the parts have to be baked before a reflow that happens more than 168 hours later. That is a line discipline question rather than a purchasing one, and our incoming inspection plan page sets out the checks we run on a tube lot.
The grade is the second decision. The UA bin is cheaper and is the correct buy when the channel is trimmed or when the full scale is large relative to the offset; the U bin is the correct buy when the channel is calibrated at temperature and the drift budget is tight. Both are active, so the choice is a specification choice rather than an availability one.
Questions that arrive with this part number
Whether the UA bin can be used where the U was specified is the first question, and the answer depends on the trim: the pin out, the gain equation and the noise are identical, and the offset window is twice as wide, so a trimmed channel accepts the substitution and an untrimmed one may not.
Whether the tube and the reel are the same part is the second, and they are, with the carrier and the quantity as the only differences. The third question is the bias current, which is 10 nA maximum on the UA rows against 5 on the U, and on a 10 kΩ source that is 100 µV against 50, which is the same order as the offset itself and has to be counted in the budget rather than ignored.