INA128PA
Product Specifications
INA128PA
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA128PA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA128PA: the A grade eight pin plastic DIP in a 50 piece tube
The INA128PA is the A grade of the eight pin plastic DIP in a 50 piece tube. The A suffix is a tighter offset and gain error bin on the same die, and on a DIP it is bought for the same reason as on any other body: a channel with a small full scale and no trim needs the tighter bin, and the grade costs nothing in the footprint because the body and the pinout are identical to the plain P code.
The device is the family: three op amp instrumentation amplifier, current feedback input stage, 700 µA of quiescent current, 120 dB of common mode rejection, 5 nA of bias current, 8 nV per root hertz of noise, plus or minus 2.25 V to plus or minus 18 V, and 200 kHz of bandwidth at a gain of 100. The socket friendly DIP body is what makes this code the calibration bench part rather than a production part.
The INA128PA rows as the addendum publishes them
| Part class | Precision instrumentation amplifier, three op amp, current feedback |
| Vendor status | Active, production |
| Data sheet | SBOS051G, revised January 2026 |
| Grade | A suffix, tighter offset and gain error window |
| Gain equation | G = 1 + 50 kΩ divided by RG |
| Input offset voltage | Family row 50 µV maximum, tighter on the A bin |
| Offset drift | 0.5 µV per degree maximum, both grades |
| Input bias current | 5 nA maximum |
| Common mode rejection | 120 dB minimum |
| Bandwidth | 1.3 MHz at a gain of 1, 200 kHz at a gain of 100 |
| Input protection | Plus or minus 40 V without damage |
| Supply range | Plus or minus 2.25 V to plus or minus 18 V |
| Quiescent current | 700 µA typical |
| Body | PDIP, P outline, 8 pins, 9.81 by 9.43 mm |
| Carrier | 50 pieces per tube |
| Lead finish | Published as call TI on the P rows |
| Temperature range | Minus 40 to plus 85 degrees |
| SOIC sibling | INA128UA and INA128UA/2K5 with the same die and grade |
50 µV of offset and half a microvolt per degree
The offset row for this family is 50 µV maximum with 0.5 µV per degree of drift, and the pair is what separates it from a general purpose op amp front end. Over a 40 degree excursion the offset moves 20 µV, which on a 10 mV full scale bridge is 0.2 per cent, so a channel built on INA128PA can hold its accuracy across the cabinet temperature without a heater or a chopper. The same excursion on a 10 µV per degree part moves 400 µV, which is 4 per cent of that full scale and larger than any plausible bridge nonlinearity.
The offset is quoted at a gain of 1 and divided by the gain at higher settings in the vendor table, which matters when a channel runs at a gain of 100: the input referred offset falls to a fraction of a microvolt while the gain error does not fall at all. That asymmetry is why the accuracy budget at high gain is set by the resistor rather than by the amplifier, and why a 0.1 per cent resistor is worth more than the next grade of amplifier.
Current feedback input stage and bandwidth at a gain of 100
The INA128 and INA129 use a current feedback input stage, and the reason is visible in one number: 200 kHz of bandwidth at a gain of 100. A voltage feedback instrumentation amplifier loses bandwidth in proportion to gain, so a part with 1.3 MHz at unity gain is down to a few kilohertz at a gain of 100. The current feedback topology holds the curve much flatter, which is what lets INA128PA serve a multiplexed data acquisition front end at a gain that would otherwise be too slow to scan.
Current feedback has a cost that the data sheet states plainly: the feedback impedance has to be resistive and short. The gain resistor should sit within a few millimetres of the RG pins and should be a metal film part, because inductance in that path shows up as peaking in the step response rather than as a gain error. At a gain of 1000 the resistor is around 50 Ω, where a centimetre of trace is a measurable fraction of the impedance, so the placement advice is not decorative.
The D body at 4.9 by 6 mm against the P body at 9.8 by 9.4 mm
The family ships in two bodies, an eight pin SOIC measuring 4.9 mm by 6 mm and an eight pin plastic DIP measuring 9.81 mm by 9.43 mm, and the difference is a process decision rather than an electrical one. The D body runs on the reflow line with the rest of the board and is the default for a new build; the P body needs plated through holes, a separate insertion step and either wave or selective solder, and on a board with a handful of DIP parts that second process usually costs more than the part.
The reason to keep the P body is mechanical. A socketed DIP can be replaced in the field or swapped during calibration without a rework station, and the longer leads absorb a mismatch between the board and a connector. A probe amplifier that is trimmed on the bench is a genuine case for the socket. On INA128PA the die and the pinout are the same in both bodies, so a board can move from one to the other without an electrical change, and the footprint is the only thing that has to be revisited.
The REF pin, the 8 Ω rule and single supply references
The REF pin sets the output level and is part of the signal path in a way that is easy to forget. Any resistance in series with it appears as a common mode error at the input and as a gain error at the output at the same time, and the vendor states that 8 Ω is enough to degrade common mode rejection on a typical part. A divider made of two 10 kΩ resistors has a source impedance of 5 kΩ, which is three orders of magnitude above that, so an unbuffered divider is not a reference for INA128PA at any gain.
On a bipolar supply the REF pin goes to ground, and ground has to be the same ground the converter uses or the difference appears as an offset. On a single supply the pin goes to a buffered mid rail, and the buffer has to be able to sink and source the current the REF pin draws, which is small but not zero. A shunt reference with a 1 µF capacitor is the cheap answer; an op amp buffer is the answer when the reference also has to drive other channels. Both are one more part than a divider and both are the reason a single supply channel measures what it claims.
120 dB of common mode rejection and the source imbalance that removes it
The common mode rejection row is 120 dB minimum on the family, measured with a 1 kΩ source imbalance, and it is the number that decides whether a bridge channel can reject a 50 Hz disturbance. Rejection degrades with source imbalance at roughly 1 dB per 100 Ω above the test condition, so a channel with a 10 kΩ mismatch between the two input legs has thrown away most of the 120 dB. In practice that mismatch comes from the sensor rather than from the board: a 350 Ω bridge with one leg 5 Ω high, or a thermocouple with a 2 kΩ cable resistance on one side only.
The fix is a pair of matched resistors at the input, or a buffer for each leg, or a sensor with a trimmed output impedance. The REF pin is part of the same problem: the vendor notes that 8 Ω in series with REF is enough to degrade rejection on a typical part, so the reference has to be driven from a low impedance source such as an amplifier or a shunt reference with a capacitor, not from a divider alone. On INA128PA the rejection also falls with frequency, and the vendor curve of rejection against frequency is the one to read for a switching supply disturbance rather than the dc row.
Gain error rows, the A grade and the 0.024 per cent window
Gain error on this family is quoted per gain setting and per grade, and the tightest row is 0.024 per cent at a gain of 1 on the A grade parts. That figure is smaller than the tolerance of the resistor that sets the gain, so the resistor, not the amplifier, is what a calibration adjusts. At a gain of 100 the family rows widen and the A grade still holds a window about half as wide as the plain grade, which is the practical difference between the two bins on a channel that is calibrated once rather than per unit.
Nonlinearity is 0.001 per cent of full scale on the plain grade and 0.0005 per cent on the A grade, which is well below any converter this part is likely to drive. The number that limits a real channel is the gain drift, quoted in ppm per degree, because it cannot be trimmed at the bench and it moves with the cabinet temperature. On INA128PA the drift row is the one to put in a specification that has to hold over temperature, and the room temperature gain error row is the one to put in a production test limit.
Buying INA128PA
The grade is the whole purchase decision. A DIP in a tube is available in the plain and the A bin at similar prices, and the difference only shows on a channel whose full scale is small enough for the offset window to matter. Writing the A into the order line is the only control, because the marking is not something a receiving clerk can read as a grade without the label.
The second consideration is that this is a bench and calibration part. A socketed DIP is inserted and removed, and the lead finish on the P rows is published as call TI, so a gold finish and a tin finish are both possible. A gold finish survives repeated insertion and a tin finish does not, which is the reason to ask for the finish in writing on a socketed application. Our supplier quality audit page covers how the finish and the label are checked at the source.
Questions that arrive with this part number
Whether the A grade is worth the premium is the first question, and on a 10 mV full scale it is: 50 µV is half a per cent of range and the A bin is tighter, which can remove a trim from a calibration fixture. The second question is whether the part can be used at unity gain, and it can, because the gain equation gives 1 with the resistor open and the input stage is stable there.
The third is the reference. The P body has the REF pin on pin 5 and the socket contact is in the signal path, so the reference has to be driven from a low impedance source rather than a divider. A divider with a 5 kΩ source impedance is three orders of magnitude above the 8 Ω the vendor names as the point where rejection starts to fall.