Contact Us

TPS71719DCKR

Brand: Texas Instruments
Texas Instruments TPS71719DCKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS71719DCKR — Power Management & Signal Chain | Superb Automation

TPS71719DCKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS71719DCKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS71719DCKR 1.9 V low noise regulator in a five pin SC70

The TPS71719DCKR is the 1.9 V member of the TPS717 family in the DCK body, the five pin SC70 of 2 mm by 1.25 mm. It delivers 150 mA from an input of 2.5 V to 6.5 V with 170 mV of dropout at full load, 70 dB of rejection at 1 kHz and 30 microvolts RMS of noise. The 1.9 V row sits in the gap between the 1.8 V logic rail and the 2.5 V analogue rail, and it exists for loads whose data sheet asks for that narrow window, such as a sensor whose bias is specified at 1.9 V plus or minus 3 percent.

The leaded body is the reason to pick this order code over the WSON members of the same family. A five pin SC70 is easier to inspect and easier to rework, and on a board that is assembled in small volumes the difference in handling cost is larger than the difference in area. The electrical table is identical to the rest of the family, so the body does not change the electrical behaviour, only the thermal path.

Ground current is 45 microamps, which is a figure to check against a product that sleeps, and the part is stable with a 1 microfarad ceramic output capacitor. It carries a current limit and thermal shutdown, and it is specified over a junction range of minus 40 to plus 125 degrees.

Key parameters from the SBVS068I document

Input range2.5 V to 6.5 V
Output1.9 V fixed on this order code
Output current150 mA
Dropout170 mV typical at 150 mA
PSRR70 dB at 1 kHz, 67 dB at 100 kHz, 45 dB at 1 MHz
Noise30 microvolts RMS from 100 Hz to 100 kHz
Ground current45 microamps
Accuracy3 percent worst case over load, line, process and temperature
PackageDCK five pin SC70, 2 mm by 1.25 mm
Order codeTPS71719DCKR, active in the vendor addendum

What the SC70 body costs and what it buys

A five pin SC70 has no thermal pad, so the only path from the die to the board is through the leads and the moulding. At 150 mA and a 1.5 V input to output difference the part burns 225 mW, which the SC70 can carry on a modest copper area but not on a thin trace in still air. The WSON members of the family use a pad, which is why they hold more dissipation in the same footprint.

What the body buys is assembly tolerance. A 0.65 mm pitch leaded package is within the capability of any line, needs no special stencil and can be reworked with a hand tool. For a prototype run or a low volume instrument that is worth more than the area, and the electrical behaviour is the same as the smaller bodies.

Where this part fits

Sensor supplies, audio front ends, precision references, wireless modules and any rail at 1.9 V that has to be quiet and small. The family is also a common choice for the analogue rail of a mixed signal board where the digital rail is 1.8 V and the analogue section wants a little more headroom. Our notes on comparing a linear post regulator against a filter after a converter are under power management cross reference, and the checks for a leaded part on a mixed board are in incoming inspection plan.

What to check before a purchase order

Check the dissipation in the leaded body at the operating input. A 5 V input into a 1.9 V output at 150 mA is 465 mW, which is beyond what a five pin SC70 will hold for long in still air, so the SC70 version belongs on rails fed from 3.3 V rather than 5 V. That is a board level decision, not a part level one, and it is easy to miss when the WSON version of the same family was used on the previous revision.

Check the output capacitor against the stable range and place it at the pin. A 1 microfarad ceramic is small enough that the trace between the capacitor and the pin is a meaningful part of the loop, and a capacitor placed at the load rather than at the regulator is a common cause of a rail that looks clean at DC and rings at a few hundred kilohertz.

Questions that come up on this part

Is the 1.9 V output adjustable? No. The fixed rows of this family are factory set, and a rail that needs trimming belongs on the adjustable member, which is a different part number.

Does the part need a minimum load? No, it is stable from no load, which is what allows it to feed a sensor that sleeps.