Contact Us

TPS62841DLCR

Brand: Texas Instruments
Texas Instruments TPS62841DLCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62841DLCR — Power Management & Signal Chain | Superb Automation

TPS62841DLCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62841DLCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62841DLCR: the 750 mA member that can be silenced on demand

TPS62841DLCR is the VSON member of the TPS6284x family, 1.5 mm by 2 mm, eight pins, no exposed pad. It takes 1.8 V to 6.5 V in, delivers 750 mA, and holds an output between 0.8 V and 1.55 V that is set by a single E96 resistor on the VSET pin. On paper that is the same converter as the other two bodies in the family. On a board it is the member that keeps two features the smaller WCSP body gives up: a MODE pin that forces PWM, and a STOP pin that stops the switching dead.

STOP is the reason this tail exists in our catalogue. The data sheet says plainly that the STOP pin is only present on the DLC package. When it is driven high the regulator finishes the switching cycle it is in and stops, and the load runs off the charge already sitting in the output capacitor. No switching noise is generated for as long as the pin stays high. That is the state a precision analog front end or a radio sensitivity test needs, and it is the state that a plain buck cannot give you without an external switch in series with the rail.

The numbers on this page come from SLVSEC6D, revised March 2020, and from the orderable addendum at the back of that document. The DLC tail is packed 3000 pieces on a large reel with a NIPDAU finish and marking E9, rated minus 40 to 125 degrees junction and level 1 at 260 degrees for moisture.

What the order code sits on

Functionsynchronous step-down converter, integrated high side and low side switches
Input range1.8 V to 6.5 V, 7 V absolute maximum on VIN
Output range0.8 V to 1.55 V in 50 mV steps
Output current750 mA
Quiescent current80 nA typical at 1.2 V out, 60 nA at 1.8 V out, no load
Forced PWM current3 mA typical no load with MODE held high
STOP mode current70 microamps typical from the input while switching is stopped
Shutdown current25 nA typical with EN low
Switching frequency1.8 MHz nominal
Switch current limit1.2 A typical high side, 1.0 A typical low side
Negative current limitminus 533 mA, so the inductor does not run away at light load
Current limit delay50 ns propagation
Output discharge35 mA typical sink on VOS after disable
PackageVSON-HR, 8 pins, 1.5 mm by 2 mm, no thermal pad
Thermal resistance105.6 degrees per watt junction to ambient on the JEDEC board
Pin count8, with STOP on pin 6 and MODE on pin 3
Carrier3000 pieces on a large reel, marking E9, NIPDAU finish
Moisture levellevel 1 at 260 degrees, unlimited floor life

How STOP behaves, and what it costs

Driving STOP high does not put the part into shutdown. The output stays up, held by the output capacitor, and the converter simply does not switch. The data sheet puts the input current in that state at 70 microamps typical, which is three orders of magnitude above the 80 nA of normal no-load operation. That is not a bug: the reference, the comparator and the control logic stay alive so the part can resume in one cycle.

The trap is what happens if the pin is left high too long. The output falls as the load drains the capacitor, and below the set point the device clamps the output about 0.5 V under the programmed voltage rather than letting it collapse. If the microcontroller that drives STOP does not bring it low before the rail reaches a level the rest of the board can tolerate, the analog block sees a slow brown-out instead of a clean window. In a test fixture that is fine because the measurement is over in milliseconds. In a product that uses STOP as a low power state, the controlling micro has to bring the pin back before the capacitor is gone.

Resume is immediate, with no soft start and no start-up delay, which is the point of the feature. The pin has an internal 450 k pull-down to ground that is disconnected once a high level is detected, the same arrangement as the EN pin, so a floating STOP pin does not leave the converter in an undefined state. Whenever we see a board where the STOP net runs past a connector, we ask for a 100 k pull-down at the connector pin, because the internal pull-down is not there once the pin has been driven high.

Choosing the output and the parts around it

The output is latched at start-up from the resistor on VSET and the converter switches off the readout circuit afterwards, so the resistor does not sit in the leakage budget. The two numbers that decide whether the latch works are the E96 window for the chosen step and the 100 pF limit on parasitic capacitance from VSET to ground. A 15.8 k resistor gives 1.2 V and accepts anything between 15.17 k and 16.43 k, which covers a 1 percent part over temperature.

0.8 VVSET to GND, no resistor
0.9 V1.74 k, window 1.67 k to 1.81 k
1.0 V4.32 k, window 4.15 k to 4.49 k
1.1 V8.45 k, window 8.11 k to 8.79 k
1.2 V15.8 k, window 15.17 k to 16.43 k
1.3 V28.7 k, window 27.55 k to 29.85 k
1.4 V52.3 k, window 50.21 k to 54.39 k
1.55 V267 k, window 256.32 k to 277.68 k
Inductor2.2 microhenry nominal, effective window 1.51 to 2.9 microhenry
Input capacitor4.7 microfarad ceramic, at least 3 microfarad effective
Output capacitor10 microfarad nominal, effective window 10 to 40 microfarad
VSET parasitic100 pF maximum from the pin to ground

The input capacitor is the part that gets cut first on a cost review, and on this family it is the one that cannot be cut. The data sheet asks for a 4.7 microfarad ceramic placed at the VIN pin for spike suppression, and the recommended operating conditions list 3 microfarad as the minimum effective value. A 4.7 microfarad part in an 0603 case with a 6.3 V rating that has lost half its capacitance at 5 V bias is already at the floor, which is why the same rail built with a 10 V part behaves differently in a conducted emissions scan.

Thermals in a body with no pad

The VSON body has no exposed pad, so the heat leaves through the eight pins and the copper they are soldered to. The junction to ambient figure is 105.6 degrees per watt on the JEDEC test board, and the junction to case top figure is 75.7. At 3.6 V in and 1.2 V out with 750 mA the converter loses about 0.15 W, which puts the junction around 16 degrees above the surrounding board. That is comfortable at 25 degrees ambient and much less so at 70 degrees inside a sealed housing, where the same 0.15 W adds 16 degrees on top of an already warm board.

The mitigation is copper, not airflow. The two ground pins, pin 1 and the VOS return, should sit on a plane that spreads under the part, and the SW node should be kept as small as the fabrication allowance permits so the switching loss does not radiate into the sense trace. Our experience with this body on four layer boards is that a 10 mm by 10 mm copper area under the part takes roughly 20 degrees per watt off the published figure, which is the difference between a part that runs at 750 mA continuously and one that has to be derated to 500 mA in a warm box.

Where this tail is the right choice

Three cases come up in our quotes. The first is a battery powered instrument that has to make a low noise measurement while the supply is quiet, where STOP removes the switching spur from the measurement window without a second regulator. The second is a radio module that needs the converter in forced PWM while the receiver is live and in power save mode when it is not, which is the MODE pin toggled at run time. The third is a board that has to hold a rail at a fixed voltage with the smallest possible BOM, where the eight pin body with one inductor and three capacitors is the whole circuit.

For the measurement case the link between the converter and the test plan matters, and our PCBA test coverage page covers how we sequence a functional test so that the STOP window is exercised on every unit rather than on the first article only. For the substitution case, where a customer is moving from another vendor's 750 mA buck, the power management cross reference lists the pin level differences between the three bodies before anyone commits a board revision.

Questions we get on this part

Does the DLC body fit a DGR land pattern? No. The DLC is 1.5 mm by 2 mm with no pad and a different pin order, so it only drops into a board laid out for the VSON body.

Can STOP be tied to ground permanently? Yes, and that is what a board that does not use the feature should do. Tying it low keeps the converter switching and removes the 70 microamp state from the budget entirely.

Is 750 mA available at 1.8 V in? The switch current limit is 1.2 A typical and the output current rating is 750 mA, but the current available at the output falls as the input approaches the output because the duty cycle runs to 100 percent. A rail that needs 750 mA at 1.8 V in and 1.55 V out is asking the part to work at the edge of its dropout behaviour, and the efficiency curve in that corner is the one to check.

What marking should the reel carry? E9 for the DLC tail, with a NIPDAU finish and level 1 moisture at 260 degrees. A reel marked with anything else is a different body or a different family member.

Does the part need a bootstrap capacitor? No. The high side switch is a PMOS device with its own gate drive, and there is no boot pin on any of the three bodies.