Contact Us

ADG1436YCPZ-REEL7

Brand: Analog Devices
Analog Devices ADG1436YCPZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG1436YCPZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

ADG1436YCPZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG1436YCPZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADG1436YCPZ-REEL7: Dual SPDT Switch at 1.5 Ohm With 400 mA Per Channel

The ADG1436YCPZ-REEL7 is the 4 mm by 4 mm, 16-lead LFCSP body of the ADG1436, a dual single-pole double-throw switch built on the vendor's high voltage CMOS process. It is in production. The part is specified at plus or minus 15 V, at 12 V and at plus or minus 5 V, needs no separate logic supply, and takes 3 V logic on its control pins. The reason to use it rather than a signal-level analog switch is current: the LFCSP body carries 400 mA per channel continuously, and the TSSOP body of the same die carries 260 mA. Buyers moving a switch into a new board should start from the pin to pin cross reference because the two packages are not the same thermal answer.

What the numbers actually mean

On resistance is 1.5 Ohm typical with 0.3 Ohm of flatness across the signal range and 0.1 Ohm of match between the two channels. Over temperature the maximum is 2.6 Ohm. At the 400 mA continuous rating that 2.6 Ohm worst case is 1.04 V of drop and 0.416 W in the package, which is why the LFCSP body, not the TSSOP, is the one to pick for a power path.

ParameterFigureWhat it decides in a build
ConfigurationDual SPDT, break before makeTwo changeover functions in one 4 mm body
On resistance1.5 Ohm typical, 2.6 Ohm max over temperature0.416 W at 400 mA in the worst case
Flatness and match0.3 Ohm flat, 0.1 Ohm channel to channel300 ppm of gain error into a 1 kOhm load
SuppliesPlus or minus 15 V, 12 V, plus or minus 5 VOne part covers a bipolar signal chain and a 12 V rail
Current400 mA LFCSP, 260 mA TSSOPThe package, not the die, sets the current a board can pass
Logic3 V compatible, no VL pinDrives straight from a 3.3 V microcontroller pin
EnableEN pin on the LFCSP bodyAll channels off in one write, useful for a safe state

Where it can surprise a build

The EN pin exists on the LFCSP body and not on the TSSOP body. A board that relies on a single enable line to mute both channels cannot be built with the TSSOP package, and a substitution in the other direction leaves the enable function unconnected and permanently on. This is the kind of difference that a part number search does not show and a netlist review does.

On resistance flatness is quoted as 0.3 Ohm, which sounds small until it is put against the load. Into 1 kOhm it is 300 ppm, into 10 kOhm it is 30 ppm, and into a 50 Ohm attenuator network it is 0.6 percent. The switch is linear for audio and for a 1 kOhm and above signal path, and it is a distortion source in a low impedance one.

Break before make is what makes the part usable as a changeover element without shorting two sources together, but it also means there is a moment when neither channel conducts. A circuit that holds a sample or a control voltage across that gap sees the gap, and the length of it is a data sheet number rather than a guess.

Applications and how it fits a signal path

Signal routing in instrumentation, audio switching where the flatness matters, battery powered instruments that benefit from the low quiescent dissipation, and relay replacement in test equipment where a mechanical contact has worn out. When a line has to keep running while an obsolete relay is re-sourced, BOM shortage recovery is the page that walks through the check list.

The rest of the switch and multiplexer family sits on the analog and mixed-signal IC page, including the 8 to 1 multiplexers that share this process and this supply range.

Questions buyers ask about this order code

Does the YCPZ suffix mean anything beyond the package? It is the LFCSP body with the enable pin, and the reel size is what the REEL7 adds. The electrical grade is the same die as the TSSOP version, so the difference that matters is the 400 mA against 260 mA current rating and the presence of the enable pin.

Can it switch a plus or minus 15 V signal with a 3.3 V microcontroller? Yes, that is what the 3 V logic compatible input and the internal level shifting are for. The control pin does not need to swing to the analog supply.

Is 2.6 Ohm over temperature the number to use for a power path? It is the number to use for a worst case calculation. At 400 mA it produces 1.04 V of drop and 0.416 W, so the thermal pad and the copper under it are part of the current rating in practice.

Request Quote — In Stock, 100% New & Original, Full Warranty