MAX96724GTN/VY+T
Product Specifications
MAX96724GTN/VY+T
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX96724GTN/VY+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
MAX96724GTN/VY+T: four camera links into one CSI-2 output
The MAX96724GTN/VY+T is the quad tunnelling deserializer of the Analog Devices GMSL2 family in the 8 mm by 8 mm TQFN body. It receives up to four GMSL2 or GMSL1 serial inputs over 50 ohm coax or 100 ohm shielded twisted pair and presents them as one, two or four MIPI D-PHY or C-PHY output ports. Each link runs at a fixed 6 Gbps or 3 Gbps forward and 187.5 Mbps reverse, a 32 to 1 asymmetry that sizes the control channel, not the video. The device is listed as ASIL-B compliant in the F version and covers -40 C to +105 C ambient. It sits in the analog and mixed-signal IC line card with the rest of the GMSL parts.
Cable length is a loss budget, not a number in a table
The overview quotes -21.0 dB maximum insertion loss at 3 GHz for the 6 Gbps rate and -19.5 dB at 1.5 GHz for 3 Gbps. The cable table publishes three lengths per rate. Applying the aged maximum attenuation from the same table gives the real margin:
| Cable | Aged loss at 3 GHz | 6 Gbps length | Loss used | Margin of 21.0 dB |
|---|---|---|---|---|
| 3.2 mm foam coax | 1.1 dB/m | 15 m | 16.5 dB | 4.5 dB |
| 2.7 mm solid coax | 2.0 dB/m | 9 m | 18.0 dB | 3.0 dB |
| 100 ohm STP AWG26 | 2.2 dB/m | 8 m | 17.6 dB | 3.4 dB |
| 3.2 mm foam coax | 1.1 dB/m | 20 m at 3 Gbps | 22.0 dB | 2.5 dB over |
| 2.7 mm solid coax | 2.0 dB/m | 10 m at 3 Gbps | 20.0 dB | 0.5 dB over |
| 100 ohm STP AWG26 | 2.2 dB/m | 11 m at 3 Gbps | 24.2 dB | 4.7 dB over |
The lengths were set against room temperature attenuation of 0.9, 1.6 and 1.8 dB/m, where the same runs come to 18.0, 16.0 and 19.8 dB. Once the cable is aged at +105 C, every 3 Gbps row sits at or above the 19.5 dB limit, and the STP row is 4.7 dB past it. The 6 Gbps rows keep 3.0 dB or more because the limit moves to 21.0 dB at 3 GHz while the length shortens. For a harness drawing, quote the aged attenuation of the actual cable and leave the equaliser headroom for connector and inline losses, which are outside this table.
Output bandwidth after aggregation
Four 8 MP cameras at 30 frames per second and 24 bits per pixel carry 5.76 Gbps each, 23.04 Gbps together. The D-PHY outputs total 2 ports by 4 lanes by 2.5 Gbps, which is 20 Gbps, so the aggregate is 3.04 Gbps short, 13 percent. The four camera claim therefore depends on a lower bit depth, on tunnel mode carrying compressed payloads, or on fewer than four cameras running at the full rate. C-PHY at 5.7 Gbps per lane gives 22.8 Gbps over four lanes and covers the same traffic with 2.6 Gbps to spare, at the cost of a different SoC input.
Selection notes
- Forward rate is fixed per link: 6 Gbps, 3 Gbps or GMSL1 at 3.12 Gbps. A GMSL1 camera does not negotiate down from 6 Gbps on its own, the port has to be set for it.
- 16 or 32 virtual channels are available depending on D-PHY or C-PHY output, which is what allows four camera streams to share two ports without mixing frame timing.
- Two I2C ports run to 1 Mbps and nine GPIOs are configurable, so power-over-coax control and lens control can share the reverse channel.
- The GTN suffix is the 8 mm by 8 mm TQFN. The side-wettable version is a separate order code and is the one to specify when the solder joint has to be inspectable after reflow.
What belongs on the harness drawing
Four items decide whether the link trains on the first build: the cable type with its aged attenuation at the maximum ambient, the connector and inline splice losses, the power-over-coax filter network, and the length of the longest run rather than the average. The 6 Gbps rows in the table keep at least 3.0 dB of margin, the 3 Gbps rows do not, so a harness specified at 3 Gbps is the one that needs the measurement. Add the reverse channel load as well, because the 187.5 Mbps link drives the camera's control interface and an over terminated reverse path shows up as an I2C timeout rather than as a video fault. Where the deserializer itself is fixed by an existing board, the pin to pin check runs before the cable length is committed.
Questions buyers ask
Does it need an external reference clock? No. Reference over reverse lets the serializer run without a crystal and takes its clock from the deserializer, which removes one oscillator per camera module.
Can the four inputs run at different rates? Yes. The inputs are independently configurable and can mix GMSL2 and GMSL1 pixel and tunnel traffic, so a 3 Gbps surround camera and a 6 Gbps forward camera can share the part.
What should a quote include? The order code, the cable type and length, the camera resolution and frame rate, and whether the SoC input is D-PHY or C-PHY. Length and lane count decide whether the harness works at the first prototype. Send the BOM line and the harness drawing to the shortage and continuity desk and the part is quoted against the current factory lead time.
Request Quote — In Stock, 100% New & Original, Full Warranty