MAX6070AAUT50+T
Product Specifications
MAX6070AAUT50+T
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX6070AAUT50+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
MAX6070AAUT50+T: a 5.000 V SOT23 reference and what its drift costs
The MAX6070AAUT50+T is the 5.000 V, A grade member of the MAX6070/MAX6071 series reference family in the 6 pin SOT23. The A grade holds 6 ppm per degree C maximum drift against 1.5 ppm typical, with plus or minus 0.04 percent initial accuracy, 4.8 uV peak to peak of 0.1 Hz to 10 Hz noise at the 2.5 V output, 150 uA of supply current and 10 mA of sink and source capability. Output options run 1.25 V, 1.8 V, 2.048 V, 2.5 V, 3.0 V, 3.3 V, 4.096 V and 5.0 V; the wafer level package covers the 2.5 V options only. It is part of the analog and mixed-signal IC line card.
Putting the drift figure next to the converter
Six ppm per degree C across the -40 C to +125 C span is 990 ppm, which is 4.95 mV on a 5 V output. Add the 0.04 percent initial window, 2.00 mV, and the worst case before soldering is 6.95 mV. On a 16 bit converter with a 5 V span the LSB is 76.3 uV, so that budget is 91 LSB. The reference alone therefore consumes the whole 16 bit error allowance about 91 times over, and an absolute accuracy claim at 16 bits needs either a tighter grade, a ratiometric measurement, or a calibration step at test.
| Parameter | Figure | Meaning for a 5 V system |
|---|---|---|
| Initial accuracy, A grade | 0.04 percent | 2.00 mV, 26 LSB at 16 bits |
| Drift, A grade maximum | 6 ppm per degree C | 990 ppm over 165 C, 4.95 mV |
| Drift, typical | 1.5 ppm per degree C | 248 ppm, 1.24 mV |
| Noise, 0.1 Hz to 10 Hz | 4.8 uV peak to peak at 2.5 V | 32 LSB at 24 bits, 0.13 LSB at 16 bits |
| Dropout | 200 mV | a 5.0 V output needs 5.2 V at the input |
| Supply current | 150 uA | 750 uW at 5 V, 1.314 Ah over a year |
| Load current | 10 mA sink and source | enough for a 16 bit converter and its buffer |
Two numbers that change a board decision
- The 200 mV dropout means a 5.000 V reference cannot run from the 5 V rail it measures. A 5.5 V or 6 V pre-regulator is part of the reference circuit, and its own noise enters through the 85 dB rejection at the frequencies where that figure is specified.
- The 4.8 uV noise figure is quoted at 2.5 V. The 5 V option has to be read from its own noise column in the data sheet rather than scaled from the 2.5 V line, because the noise of a series reference does not follow the output voltage in a straight line.
- The filter option on this family is a pin, not a package change. If the board needs wideband noise below the published figure, order the filter version rather than adding an RC after the fact, since the added resistor spoils the load regulation that the 10 mA rating buys.
- Reverse current is limited. A reference that is pulled above its output by a decoupled rail on power-down needs a clamp, as with any series reference of this size.
Where it fits
Precision industrial and process control loops, 16 bit and 18 bit ADC and DAC channels, precision current sources and instrumentation front ends all use this part. It also appears in calibration circuits where the 6 ppm maximum replaces a periodic trim, and in battery-powered instruments where 150 uA is small against the converter's own draw.
Mounting and incoming inspection
The 6 pin SOT23 pinout carries the output, the ground, the supply and the filter or trim node depending on the option, so a reel of the wrong option is not visible until the board is powered. Check the order code on the reel label against the BOM line, not just the family name. The AEC-Q100 qualification is stated for the ordering options that carry it, which means the automotive claim belongs to specific suffixes; a general purpose suffix in an automotive build is an audit finding even though the die is the same. The WLP option is 0.78 mm by 1.41 mm with 0.35 mm bump spacing and is offered on the 2.5 V outputs only, so a 5 V board cannot use the smallest body.
Questions buyers ask
Is the A grade worth the price difference? It is the only grade with a published 6 ppm maximum. The B and non A parts carry wider limits, so if the error budget in the table above is the requirement, the A suffix in AAUT50 is the part that meets it.
What is the difference between MAX6070 and MAX6071? They share the die and the pinout; the 6070 adds the noise filter option. Order the exact suffix, because a substitution between the two changes the pin function on that node.
Can you supply against a scheduled build? Yes. Send the annual quantity, the target quarter and the output voltage to the lead time desk or the BOM line to the shortage desk and the reply carries the current factory date code and packing option, tape and reel or tube, for this exact order code.
Request Quote — In Stock, 100% New & Original, Full Warranty