Contact Us

TPS62808YKAR

Brand: Texas Instruments
Texas Instruments TPS62808YKAR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62808YKAR — Power Management & Signal Chain | Superb Automation

TPS62808YKAR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62808YKAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62808YKAR: a 1 A step down converter that sets its output from one resistor

TPS62808YKAR is a 1 A synchronous step down converter in a 1.05 mm by 0.70 mm wafer scale body, where the output voltage is chosen by a single resistor on the mode pin instead of by a divider in a DSBGA body of 6 pins. The resistor to digital converter inside the part reads one external resistor at start-up and selects one of sixteen output voltages, so the same order code serves several rails.

Order code and package

Catalogue stringTPS62808YKAR, the 1 A, 1.5 MHz, 1.8 V to 3.3 V member of the six part family
BodyYKA, DSBGA, 6 pins, 1.05 mm by 0.70 mm, junction to ambient 147.7 C per watt
Reel250 pieces on a small tape and reel, which is the only quantity printed for this string while the 0.6 A members ship at 3000
Finish and moisturemoisture level 1 and 260 C, unlimited floor life
Temperaturejunction minus 40 to 125 C
DocumentSLVSDD1G, revised June 2024
Heightthe body is thin enough for a sub 0.6 mm assembly height

Electrical parameters that decide the application

Input range1.75 V to 5.5 V, which covers a single lithium cell and a 3.3 V or 5 V rail
Output current1 A on this member, against 0.6 A on the TPS62800, TPS62806 and TPS62807
Switching frequency1.5 MHz on this member, against 4 MHz on the TPS62800, TPS62801 and TPS62802
Output range1.8 V to 3.3 V in 100 mV steps through the resistor to digital converter
Fixed option1.8 V when the mode pin is tied to ground, with no resistor fitted
Accuracy1 per cent in the features list, with the electrical table splitting the PWM and power save rows
Quiescent current2.3 uA typical and 4 uA maximum in power save with the device not switching, quoted for minus 40 to 85 C
Shutdown current120 nA typical, 250 nA maximum
Soft start400 us on this member, against 125 us on the 4 MHz parts
Output dischargeintegrated, and it pulls the rail down through 7 to 11 ohm when the enable goes low
Undervoltage lockout1.65 V to 1.75 V rising, 1.56 V to 1.70 V falling
Enable thresholds0.8 V high and 0.4 V low, with a 500 kOhm internal pull down
Thermal shutdown160 C junction with 20 C of hysteresis
Duty cycle100 per cent, so the part passes the input through when the input falls to the output

The six members and how they separate

TPS628004 MHz, 1 A, 0.4 V to 0.775 V, 25 mV steps
TPS628014 MHz, 1 A, 0.8 V to 1.55 V, 50 mV steps
TPS628024 MHz, 1 A, 1.8 V to 3.3 V, 100 mV steps
TPS628061.5 MHz, 0.6 A, 0.4 V to 0.775 V, 25 mV steps
TPS628071.5 MHz, 0.6 A, 0.8 V to 1.55 V, 50 mV steps
TPS628081.5 MHz, 1 A, 1.8 V to 3.3 V, 100 mV steps, the part on this page
Reel splitthe 0.6 A strings are printed at 3000 pieces and the 1 A string at 250, so a prototype and a production order for the same rail can need two different order codes
Mode pin levelsa high level selects forced continuous operation and a resistor to ground selects one of the sixteen voltages at start-up
Package heightthe six ball body and a 0201 passive set keep the assembly under 0.6 mm

Points to check before this part goes on a BOM

The resistor to digital converter is a start-up function, not a continuous one. The value is read once when the enable goes high and then frozen, so a resistor that drifts after start-up does not move the rail, and a resistor that is wrong for the chosen value latches a wrong output until the next enable cycle.

Sixteen steps of 100 mV across 1.8 V to 3.3 V means the nearest step to a 2.5 V rail is exact and the nearest step to a 2.85 V rail is not. A rail that needs 2.85 V should be checked against the step list rather than assumed, because the part will pick the closest value it can and will not report the choice.

The 400 us soft start on this member is more than three times the 125 us of the 4 MHz parts. On a rail feeding a large ceramic bank that difference is the whole inrush problem, and it is the reason to stay at 1.5 MHz even when board area would allow the faster part.

A 147.7 C per watt junction to ambient figure in a 1.05 mm by 0.70 mm body is the number that limits the 1 A rating. At 1 A from 3.3 V to 1.8 V the dissipation is roughly 0.3 W, which puts the junction 45 C above the board temperature on a good copper land and more on a poor one.

Moisture level 1 with unlimited floor life matters at this body size, because the part is normally placed on a panel with many others and a reel that has to be baked interrupts the line. The same applies to the 250 piece reel: it is a prototype quantity, not a production one.

Undervoltage at 1.75 V rising is above the 1.75 V bottom of the input range, which is deliberate. A cell falling through that point turns the converter off before the internal circuits run out of headroom, so the output falls cleanly instead of drifting.

What the resistor actually selects

Inside the part there is a sixteen entry table of output voltages and a resistor to digital converter that measures the resistor from the mode pin to ground at start-up. The measurement is compared with the table and the nearest entry is loaded into the feedback loop.

Because the feedback divider is internal, the accuracy of the rail does not depend on the tolerance of an external divider. The 1 per cent figure in the features list is therefore the whole output accuracy rather than a reference accuracy that has to be combined with two resistors.

The other side of the trade is that the rail is one of sixteen values. A board that needs 1.15 V, between the 0.8 V to 1.55 V member steps of 50 mV, has to use that member rather than the 1.8 V to 3.3 V one.

One order code, several rails

The same string can appear on a board three times at 1.8 V, 2.5 V and 3.3 V, differing only in the resistor. That reduces the number of lines on the BOM and the number of reels on the line, and it means a rail change is a resistor change rather than a part change.

It also means a build error in the resistor is invisible. A 3.3 V rail with a resistor set for 2.5 V is electrically valid, powers up, and fails only in the functional test, so the resistor value belongs in the first article check.

Where this order code fits

This is the converter behind a camera module, a wearable or a battery powered sensor, where board area is the constraint and the rail is one of a small number of standard voltages. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Consolidation page.

Questions buyers ask

Can the output be set to 2.85 V? No. The steps are 100 mV from 1.8 V, so 2.8 V is the nearest value and the part will regulate there. A rail that needs 2.85 V needs the 0.8 V to 1.55 V member with 50 mV steps and a different divider ratio.

Why is the reel only 250 pieces? That is the quantity the vendor addendum prints for this string. The 0.6 A members of the same body are printed at 3000, so a production order at 250 would be a prototype quantity and the reel size is worth confirming before a schedule is set.

What is the quiescent current in forced PWM? Higher than the 2.3 uA of power save mode, because the part keeps switching. The 2.3 uA figure applies with the device not switching, and that is the mode to use on a battery product.

Does it work down to 1.75 V in? It starts and runs from 1.75 V, and 100 per cent duty cycle lets it follow the input down as long as the input stays above the output plus the drop across the high side switch.

Is an external divider needed? No, and fitting one defeats the purpose. The mode pin takes a single resistor to ground, or a direct connection to ground for the fixed 1.8 V setting.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.