Contact Us

TPS62097RWKR

Brand: Texas Instruments
Texas Instruments TPS62097RWKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62097RWKR — Power Management & Signal Chain | Superb Automation

TPS62097RWKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62097RWKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62097RWKR: a 2 A step down converter with a selectable 1.5 MHz to 2.5 MHz switching frequency in a 2 mm by 2 mm body

TPS62097RWKR is a current mode step down converter with the iDCS-Control loop and both switches integrated in a VQFN-HR (RWK) body of 11 pins. It takes 2.5 V to 6.0 V in, sets the output anywhere from 0.8 V to the input voltage with a divider, holds 1 per cent accuracy over temperature, and runs either in power save mode or in forced PWM for a low noise rail. The switching frequency is set by one external resistor between 1.5 MHz and 2.5 MHz, and the soft start ramp is set by a capacitor on the same pin that carries the tracking function.

Order code and package

TPS62097RWKRVQFN-HR body of 11 pins measuring 2.0 mm by 2.0 mm, 3000 pieces on a large reel, finish shown as call TI or tin, moisture level 1 at 260 C with unlimited floor life, marking ZFZ5, active status in the addendum dated 9 November 2025
TPS6209718RWKRthe 1.8 V fixed output member in the same body, 3000 pieces on a large reel, marking ZGB5
TPS6209733RWKRthe 3.3 V fixed output member, same body and reel, marking ZGC5
T suffix250 pieces on a small reel for the same die, which is the string a repair line uses for a handful of boards
Rows with an .A or .B suffixthe addendum repeats the strings with these suffixes because a second assembly site is listed, and the packing and marking have to be read on the row rather than inferred from the suffix
Pin count11 pins with the thermal pad, and the pad is the ground return as well as the heat path

Electrical parameters that decide the application

Input voltage2.5 V to 6.0 V in the recommended table, which fits a single cell lithium rail, a 3.3 V intermediate bus or a 5 V adapter
Output voltage0.8 V to the input voltage with a divider, or 1.8 V and 3.3 V fixed on the two numbered members, both with 1 per cent accuracy over temperature
Output current2 A continuous, with the inductor and the thermal path setting what the rail can hold at a given ambient
Switch resistance40 milliohm typical and 73 milliohm maximum on the high side, 50 milliohm typical and 96 milliohm maximum on the low side, both measured at 500 mA
Current limit3.1 A minimum, 3.6 A typical and 4.2 A maximum on the high side switch, which is a forward limit, and the low side negative limit is specified separately for forced PWM operation
Switching frequency1.5 MHz to 2.5 MHz set by an external resistor, with a fixed frequency in forced PWM and the same frequency held in power save mode once the load is above the threshold
Quiescent current40 microamp typical and 57 microamp maximum into the analog and power inputs with the enable high and the part not switching, over minus 40 C to 85 C
Soft start current5.5 microamp minimum, 7.5 microamp typical and 9.5 microamp maximum out of the SS/TR pin, which sets the ramp against the capacitor on that pin
Output dischargea 165 ohm resistor from the output to ground when the enable goes low, which is what stops a rail from floating at a level that keeps a downstream device half alive
Hiccup behaviourafter the high side limit is hit 32 times the part stops switching, discharges the output and restarts, which separates a short from a heavy but valid load
Duty cycle100 per cent, so the part passes the input through with the high side switch held on when the input falls toward the output voltage
Loopthe loop is internal and is stable with output capacitors above 150 microfarad as well as with small ceramic parts, which is why there is no compensation pin
Power goodan open drain output with the release and the assertion points set inside the part, used to hold a downstream converter off until the rail is valid
Junction rangeminus 40 C to 125 C, with thermal shutdown as the last protection

Fixed and adjustable members of the family

TPS6209718the 1.8 V fixed output member, same 11 pin body, 3000 pieces on a large reel, marking ZGB5
TPS6209733the 3.3 V fixed output member, same body and reel, marking ZGC5
TPS62097this string, adjustable from 0.8 V to the input voltage, marking ZFZ5
Mode pinselects power save or forced PWM, and the forced PWM setting keeps a fixed frequency at light load so a data converter or a radio does not see a low frequency component
Newer alternativethe data sheet points at the TPS62851x family as a lower cost, smaller solution for the same 6 V input class, which is the part to compare against on a new board
Trackingthe SS/TR pin accepts a voltage to make the output follow another rail, so the same pin serves either a soft start capacitor or a tracking input
Output capacitancethe internal loop is stated to be stable with output capacitors above 150 microfarad, which is what allows the part to sit behind an existing bulk capacitor

Points to check before this part goes on a BOM

The frequency resistor is part of the BOM, not an option. The switching frequency is set by one external resistor in the 1.5 MHz to 2.5 MHz band, so a substitute board that copies the reference value instead of the value from the specific data sheet curve lands on a different frequency and a different ripple.

Forced PWM and power save mode are not the same part number. The mode is chosen on the MODE pin and the forced PWM setting keeps a fixed frequency at light load, which costs efficiency but removes the low frequency ripple that a data converter or a radio can hear.

The SS/TR pin does two jobs. A capacitor on it sets the ramp, and a voltage applied to it makes the output track another rail. A board that needs tracking loses the simple capacitor ramp, and a board that needs the ramp has to leave the pin free of an external drive.

2 A in a 2 mm body is a thermal statement. The 40 and 50 milliohm switches put the conduction loss inside an 11 pin package, so the thermal pad has to reach enough copper for the junction to stay inside 125 C at the ambient of the enclosure, not at the ambient of the bench.

The 0.8 V floor is a real limit. Rails below 0.8 V need a different part, and a 0.9 V core rail sits only 0.1 V above the floor, so the divider tolerance and the 1 per cent accuracy have to be checked against the load tolerance rather than assumed.

The discharge resistor is 165 ohm, which is a slow bleed. A 22 microfarad output discharges in a few milliseconds, and a 220 microfarad rail takes much longer, so a specification that asks for a fast collapse needs an external switch.

What a selectable frequency changes around the part

The inductor is chosen against the frequency the board actually runs. Moving from 1.5 MHz to 2.5 MHz shrinks the inductor for the same ripple, and it also moves the switching harmonics, which is often the reason a board changes the resistor late in a project when a scan fails.

The loop is internal, so the output capacitor is chosen for stability rather than for size alone. The data sheet states that the compensation covers a wide range of output capacitance, and that range is what makes the part usable on a rail that already has a large bulk capacitor behind it.

Where the 11 pin body is used

Point of load rails on a solid state drive, a programmable logic controller or a motor drive card are the usual place, because the input is 3.3 V or 5 V and the load is a 1 A to 2 A digital rail. The 2 mm by 2 mm footprint is often the reason it is chosen over a larger part with the same current.

Where this order code fits

a point of load rail behind a 3.3 V or 5 V intermediate bus in a drive card, a solid state drive or a controller Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Is this part fixed at 1.8 V or adjustable? The plain TPS62097 string is adjustable from 0.8 V to the input voltage. The 1.8 V and 3.3 V fixed options carry the 18 and 33 digits in the string, TPS6209718 and TPS6209733, so a BOM that asks for a fixed rail has to quote those strings and not this one.

How is the switching frequency set? By one external resistor, over a 1.5 MHz to 2.5 MHz range. There is no default frequency inside the part, so the resistor value comes from the curve in the data sheet for the chosen output voltage.

What happens on a shorted output? The high side limit trips, and after 32 consecutive trips the part stops switching, discharges the output and restarts. A short therefore shows as a hiccup rather than as a hot switch.

Can two of these share a rail? No. There is no current sharing or clock synchronisation between parts, so a rail above 2 A needs a single larger converter or two rails split at the load.

What floor life does the reel have? Moisture level 1 at 260 C with unlimited floor life, so unlike a level 3 part the reel does not need baking after it has been open, which matters on a line that opens and closes reels through a week.

Does SUPERB hold this string for repair demand? SUPERB quotes against the exact ordering string with date codes, packing and country of origin on the offer, and confirms the reel size before the order is placed.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.