Contact Us

TPS563249DDCR

Brand: Texas Instruments
Texas Instruments TPS563249DDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS563249DDCR — Power Management & Signal Chain | Superb Automation

TPS563249DDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS563249DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS563249DDCR 3 A synchronous buck held at a constant 1.4 MHz

The TPS563249DDCR is a 4.5 V to 17 V, 3 A synchronous buck in a 6 pin SOT-23-THIN body measuring 1.6 mm by 2.9 mm. It integrates a 70 milliohm high side and a 30 milliohm low side FET and runs at a constant 1.4 MHz, with the switching pattern fixed by the part rather than by the load. That last point is what separates this device from most of the 3 A class, where a light load drops the converter into pulse skipping and the ripple changes shape.

Control is D-CAP3, so there is no external compensation network to compute. The feedback reference is 600 mV, and the output range runs from 0.6 V to 7 V, which covers the 0.9 V to 3.3 V rails that sit behind most processors and DDR supplies. Soft start is fixed at 1.7 ms and works into a prebiased output, and the part is aimed at boards where the bill has to stay at five components per rail.

The device is an always-on-conduction part. It will not enter a skip mode at a milliamp of load, so the inductor current stays continuous and the output ripple keeps the same amplitude and the same frequency from no load to full load. For a rail that feeds an analog front end, a comparator threshold or a small signal chain, that is worth more than the extra quiescent current it costs.

Key parameters from the SLVSE54A document

Input range4.5 V to 17 V, with UVLO waking at 4.2 V to 4.4 V and shutting down at 3.6 V to 3.8 V
Output current3 A from a 70 milliohm high side and a 30 milliohm low side FET
Output voltage0.6 V to 7 V against a 600 mV reference, 594 mV to 606 mV at 25 degrees
Switching frequencyConstant 1.4 MHz, 1250 kHz to 1550 kHz over the production spread
Current limitHigh side source 5.5 A to 7.1 A, low side source 3.1 A to 4.7 A, low side sink 1.1 A to 1.7 A
Shutdown current2.5 microamp typical and 10 microamp maximum at 25 degrees with the enable pin low
Soft startFixed 1.7 ms, starts into a prebiased output
Timing limitsMinimum on time 50 ns, minimum off time 250 ns
Package6 pin SOT-23-THIN, 1.6 mm by 2.9 mm, DDC body, 3000 pieces on a large reel

What 1.4 MHz buys and what it costs

At 1.4 MHz the inductor for a 3 A rail lands near 1 microhenry to 1.5 microhenry, which is a 3 mm by 3 mm part rather than the 5 mm by 5 mm that a 500 kHz part needs. The output capacitor bank also shrinks because the ripple frequency is higher, so the whole rail fits in a corner of a dense board. The cost is switching loss: the two FETs are turned every 714 ns, and the gate charge and the drain node capacitance are paid at that rate whether the load is 3 A or 30 mA.

The conduction loss is set by the two resistances. At 3 A from 12 V to 1.8 V the high side conducts for about 15 per cent of the period and the low side for the rest, which puts roughly 0.09 W in the high side and 0.23 W in the low side before any switching term. A SOT-23-THIN body with a 1.6 mm by 2.9 mm footprint has to pass that heat into a small copper island, so 3 A at 25 degrees ambient is realistic and 3 A at 85 degrees in a closed box is not.

The constant frequency also fixes where the switching noise lands. A 1.4 MHz carrier with its harmonics is easy to keep out of a 455 kHz intermediate frequency or an audio band as long as the board does not couple the switch node into a high impedance trace. That predictability is the reason to pick this part over a cheaper pulse skipping device when the rail feeds something that listens.

Where this part fits

Set top boxes, industrial controllers, instrumentation and any board where a 3 A rail has to stay quiet at light load. The constant frequency makes it a natural choice for a rail that powers an ADC reference buffer or a low noise amplifier bias. Our desk keeps the family comparison and the substitution notes for this class, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

The DDC suffix is the 6 pin SOT-23-THIN, which is thinner than the SOT-23-6 used by older 3 A devices, so a board that was laid out for the older body needs a pad check rather than a guess. The reel is 3000 pieces in the DDCR row and 250 in the DDCT row, and the DDCR.A row of the same string carries an added suffix with the same 3000 piece quantity, so the order line has to name the exact row.

Confirm the inductor against the 7.1 A top of the high side limit rather than against the 3 A rating, because a short circuit will drive the inductor to the limit before the hiccup counter trips. Confirm the 1.7 ms soft start against the upstream supply, since a 100 microfarad output bank charged in 1.7 ms draws about 60 mA of average inrush on top of the load. See incoming inspection plan for the receipt check on a six pin thin body.

Questions that come up on this part

Does the part skip pulses at light load, is the first question, and the answer is no. It stays in continuous conduction, which is why the standby current is higher than a pulse skipping sibling and why the ripple is flat. A product that has to meet a 1 mA standby budget should look at a different member of the family, and a product that has to meet an emissions or noise limit should stay with this one.

The second question is whether 17 V is enough for a 12 V rail with transients. The absolute maximum is above the operating range, but the recommended operating ceiling is 17 V, and a 12 V bus with a hot plug event can ring well past that. A TVS at the input and a check of the actual transient on the bench is cheaper than a field return.