TPS62085RLTT
Product Specifications
TPS62085RLTT
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62085RLTT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62085RLTT: a 3 A step down converter in a 2 mm by 2 mm body, ordered on a 250 piece small reel
TPS62085RLTT is a synchronous step down converter with the DCS-Control loop, both switches and a hiccup short circuit protection inside the package in a VSON-HR (RLT) body of 7 pins. It takes 2.5 V to 6.0 V in, holds an adjustable output from 0.8 V up to the input voltage, and delivers 3 A with 31 milliohm high side and 23 milliohm low side switches. The switching frequency is 2.4 MHz, which is what keeps a 0.47 microhenry inductor and a 22 microfarad output capacitor enough for a full 3 A rail. Quiescent current is 17 microamp, the internal loop is stable with output capacitors from 10 microfarad to 150 microfarad, and a hiccup counter turns a shorted output into a retry rather than a hot switch.
Order code and package
| TPS62085RLTT | VSON-HR body of 7 pins measuring 2.00 mm by 2.00 mm, 250 pieces on a small reel, moisture level 1 at 260 C with unlimited floor life, marking PD5Q, active status in the addendum dated 8 November 2025 |
| TPS62085RLTR | the same die on a 3000 piece large reel, which is the string a production line orders once the pilot quantity has passed |
| TPS62085RLTT.B | the .B row of the small reel string prints 3000 pieces on a large reel, which contradicts the plain row, so the reel size has to be confirmed on the packing list rather than read from the suffix alone |
| TPS62086 and TPS62087 | the fixed 1.8 V and 3.3 V members in the same body, with the same current rating and the same pinout, so a board can move between them without a copper change |
| Pin count | 7 pins with the thermal pad, and the pad is the ground return as well as the heat path |
| Body height | the VSON-HR body is 1 mm high, which is why the part is used on the back of a board behind a connector or a shield can |
Electrical parameters that decide the application
| Input voltage | 2.5 V to 6.0 V, which covers a single cell lithium rail, a 3.3 V intermediate bus and a 5 V adapter without a pre-regulator |
| Output voltage | 0.8 V to the input voltage on this adjustable member, with the fixed members covering 1.8 V and 3.3 V from the same die |
| Output current | 3 A continuous, with the thermal pad and the copper under it deciding how much of that current survives at the ambient inside the enclosure |
| Switch resistance | 31 milliohm typical and 56 milliohm maximum on the high side, 23 milliohm typical and 45 milliohm maximum on the low side, both at 500 mA |
| Current limit | 3.7 A minimum, 4.6 A typical and 5.5 A maximum on the high side switch, which is the peak figure that starts the hiccup counter |
| Switching frequency | 2.4 MHz in PWM mode at 1 A, which is the frequency that makes a 0.47 microhenry inductor practical |
| Quiescent current | 17 microamp typical and 25 microamp maximum into the input with the part enabled and not switching, over minus 40 C to 85 C |
| Shutdown current | 0.7 microamp typical and 5 microamp maximum with the enable pin low, which is the figure a standby budget uses |
| Undervoltage lockout | 2.1 V minimum, 2.2 V typical and 2.3 V maximum on a falling input, with 200 mV of hysteresis on the way back up |
| Soft start | 0.8 ms from the enable pin going high to 95 per cent of the nominal output, fixed inside the part |
| Power good | an open drain output that releases between 93 and 98 per cent of the nominal output and drops near 88 per cent on the way down, which is a window rather than a single point |
| Output accuracy | plus or minus 1 per cent in PWM mode at 1 A with at least 1 V of headroom, and the feedback pin sits at 800 mV with a 792 mV to 808 mV window at 25 C |
| Output discharge | a 260 ohm resistor from the output to ground when the enable goes low, which stops a rail from sitting at a level that keeps a downstream device half alive |
| Thermal shutdown | 150 C on the rising edge with 20 C of hysteresis, as the last protection rather than as an operating point |
Tape and reel rows of this converter
| TPS62085 | this member, adjustable from 0.8 V to the input voltage, 3 A, 2 mm by 2 mm VSON-HR |
| TPS62086 | the fixed 1.8 V member of the same family, same body, same pinout, same current and the same 2.4 MHz loop |
| TPS62087 | the fixed 3.3 V member, same body and pinout, which is the string a 3.3 V rail orders instead of fitting a divider |
| Light load behaviour | power save mode is entered automatically, so the quiescent current falls at light load and the ripple changes with the load |
| Hiccup | after repeated high side current limit events the part stops, discharges and restarts, which separates a short from a heavy load |
| Output capacitor window | 10 microfarad to 150 microfarad, stated as stable, so a rail with a moderate bulk capacitor behind it is inside the specified range |
| Packing | 250 pieces on a small reel for the T suffix and 3000 on a large reel for the R suffix, with one .B row printing a different reel size |
Points to check before this part goes on a BOM
3 A is a thermal rating as much as an electrical one. The 31 and 23 milliohm switches put the conduction loss inside a 2 mm body, and the data sheet has a thermal section that says so. A board that asks for 3 A at 85 C ambient needs the copper area the vendor shows, not the copper a 1 A part got away with.
The hiccup counter separates a short from a heavy load. After the high side limit trips repeatedly the part stops switching, discharges the output and restarts. A rail that restarts every few milliseconds is telling the board that the load is a short, not that the converter is weak.
Power save mode is not a mode pin on this member. The converter enters power save automatically at light load, which is what brings the quiescent current down. A rail that must stay at a fixed frequency at light load needs the forced PWM member of the family rather than a resistor change.
The output capacitor window is wide but not unlimited. The internal loop is stated to be stable from 10 microfarad to 150 microfarad, so a rail with a 470 microfarad bulk capacitor behind it needs the loop checked rather than assumed.
The .B row of this string prints a different reel size. The plain T row says 250 pieces on a small reel and the .B row of the same string says 3000 on a large reel. That is a printing inconsistency in the addendum, and the packing column on the offer is what settles it.
The enable pin has a 400 kilohm pulldown. An unconnected enable therefore turns the part off rather than leaving it in an undefined state, which matters on a board where the enable comes from a connector that may not be fitted.
Where a 2 mm converter with a 250 piece reel is the right buy
Pilot builds and repair lines order the T suffix because a full reel is more parts than the build will consume before the reel ages out. The same die on a small reel costs more per part and saves the carrying cost of a reel that sits half used, which is why the T string exists at all.
The trade is real on a line that runs the same board every month: at that point the large reel is cheaper per part and the 250 piece reel becomes the exception. The important thing is that both strings carry the same die and the same marking, so a board qualified on one is qualified on the other.
What the 2.4 MHz frequency changes for the board
A 2.4 MHz converter puts its switching harmonics well above the audio band and above the AM band, which is why it turns up on audio boards and on radios. The cost is switching loss and a tighter limit on how much copper the board can add before the emissions scan notices.
The inductor is small but it is still the part that sets the ripple current. A 0.47 microhenry part at 2.4 MHz gives a ripple that the output capacitor absorbs, and a larger inductor lowers the ripple at the cost of transient response.
Where this order code fits
a point of load rail behind a 3.3 V or 5 V bus on a drive card, a set top box or an industrial controller Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Reduce Component Cost page.
Questions buyers ask
Is this part fixed or adjustable? The plain TPS62085 is adjustable from 0.8 V to the input voltage. The 1.8 V and 3.3 V fixed options are the TPS62086 and TPS62087 members of the same family, in the same body and on the same pinout.
Why is this string on a 250 piece reel? The T suffix is the small reel. The same die on a 3000 piece large reel is the R suffix, and the .B row of the T string prints the large reel quantity, so the packing column on the offer is the figure to trust.
What happens on a shorted output? The high side current limit trips at 3.7 A minimum, and after repeated trips the part enters hiccup, discharges the output and restarts. The rail therefore pulses rather than staying dead or cooking the switch.
How much output capacitance can it drive? The internal loop is specified as stable with 10 microfarad to 150 microfarad of output capacitance, so a small ceramic rail and a rail with a moderate bulk capacitor are both inside the stated window.
Does the part discharge the output when disabled? Yes, through a 260 ohm resistor, which empties a 22 microfarad rail in well under a millisecond and a much larger rail in proportion to its size.
Can SUPERB supply the small reel and the large reel on one order? SUPERB quotes each ordering string separately with date codes, packing and country of origin, so a build that needs both quantities gets two lines on one offer rather than a substitution.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.