CD4027BE
Product Specifications
CD4027BE
Texas Instruments — Power Management & Signal Chain
Product Overview
The CD4027BE from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
CD4027BE: two J-K master-slave flip-flops in a 16-lead plastic DIP
CD4027BE is the through-hole member of the CD4027B family, two independent J-K master-slave flip-flops in a 16-lead plastic DIP, 25 pieces to a tube. The vendor descriptor reads CMOS Dual J-K Master-Slave Flip-Flop, the document is the CD4027B data sheet revision D, and the parametric table gives two channels, balanced outputs, clear and preset inputs, positive edge triggering, a positive input clamp diode and standard speed with propagation above 50 ns. The feature line adds a 16 MHz typical clock toggle rate at 10 V and a static operation that retains state indefinitely with the clock at either level.
The addendum lists CD4027BE as Active in production, PDIP (N) with 16 leads, 25 pieces to a tube, RoHS yes with a nickel-palladium-gold finish, no moisture level for the through-hole body, minus 55 to plus 125 degrees, and the marking CD4027BE. The same document carries CD4027BF and CD4027BF3A in ceramic, CD4027BM as an obsolete SOIC row with a blank quantity, CD4027BM96 as the active reel at 2500 pieces and CD4027BMT as a second obsolete row, so the plastic DIP and the reel are the two formats a buyer can still order.
The CD4027BE row as the vendor addendum publishes it
| Part class | Dual J-K master-slave flip-flop with clear and preset |
| Vendor descriptor | CMOS Dual J-K Master-Slave Flip-Flop |
| Vendor document | CD4027B data sheet revision D |
| Channels | Two, each with J, K, clock, set and reset, and complementary outputs |
| Toggle rate, vendor feature line | 16 MHz typical at 10 V |
| Edge | Positive edge triggered |
| Static behaviour | Retains state indefinitely with the clock at either level |
| Output drive, parametric table | 1.5 mA sink and source |
| Input type, parametric table | TTL |
| Input type, data sheet description | B series CMOS levels |
| Supply range | 3 V to 18 V |
| Quiescent current | Tested to maximum at 20 V on every unit |
| Package for this code | PDIP (N), 16 leads |
| Packing | 25 pieces in a tube |
| Lead finish | NIPDAU |
| Moisture level | Not applicable for this package type |
| Operating range | Minus 55 to plus 125 degrees |
| Status | Active, production |
| Part marking | CD4027BE |
| SOIC rows | CD4027BM Obsolete, CD4027BM96 Active at 2500 pieces |
| Second obsolete SOIC row | CD4027BMT, quantity blank, Call TI |
| Ceramic rows | CD4027BF and CD4027BF3A, 25 piece tube |
The toggle state, and why a J-K saves gates
A J-K flip-flop defines the toggle condition internally: with both J and K high the output complements on every clock edge, with both low it holds, and with one high it sets or clears. A D flip-flop reaches the same toggle state only by connecting the Q bar output back to the data input, which costs a wire and, on a crowded board, a via. Where the toggle condition is a logic term rather than a constant, the J-K wins twice: the term drives one input and its inverse drives the other, and no feedback wire is needed.
The master-slave structure is what allows the part to be edge triggered rather than level sensitive. The master stage takes the input while the clock is low, the slave stage transfers on the rising edge, and the output therefore changes once per edge regardless of how long the clock stays high. That is the behaviour a counter needs, and it is the reason the 4027 appears in ripple counters, in divide by two stages and in the classic toggle latch that a single button drives.
The input type line that contradicts the data sheet
There is one inconsistency on this part that a buyer should know about before it reaches a board. The vendor parametric table lists the input type as TTL, while the data sheet describes the part as a B series CMOS device with the standard CMOS input structure and the noise margins that go with it. The two statements are not the same, and the practical difference is the input threshold: a TTL level input switches at about 1.4 V whatever the supply, while a CMOS input switches at a fraction of the supply and draws almost no current.
For a circuit driven from another CMOS gate at the same rail the distinction does not change the behaviour, because a CMOS output swings to both rails and satisfies either threshold. It matters when the driving source is a 5 V logic output feeding a 4027 that runs at 12 V: a CMOS input would not see a valid high, and a TTL input would. This page states both readings rather than choosing one, and a circuit that depends on the threshold should be checked against the direct current table of the document.
Set, reset and the outputs that must not fight
Set and reset on this part are asynchronous and act independently of the clock. Both high at once drives both outputs high, which is a state the data sheet defines but a circuit rarely wants, and the moment both are released the flip-flop settles into a state that depends on which input falls first. A circuit that can assert both at once, for example a reset line and a preset line driven from the same controller, should sequence them rather than rely on the part.
The outputs are complementary and both are brought out, which is convenient and also a hazard: wiring Q and Q bar together shorts a high output to a low one through the output stages, and the resulting current can damage the part. A 1 k resistor between the two will not prevent it, and the only safe rule is that the two outputs never meet.
Where the 4027 sits against the 4013 and the 4043
The CD4013B is the D-type sibling, also two flip-flops, also with independent set and reset, in a 14-lead body. The CD4027B takes 16 leads because it has two more input pins, and it wins wherever the toggle condition or the J-K steering table saves external gates. The CD4043B is the latch rather than the flip-flop: four NOR set-reset latches with three state outputs, which is the right part for holding a flag rather than for counting.
A board that divides a clock takes either, a board that implements a state machine in discrete logic usually takes the 4027 because the steering table is built in, and a board that needs to hold eight flags takes the 4043 for its four latches per package and three state outputs.
Incoming checks on a J-K part
The functional check has four states per flip-flop: hold, set, clear and toggle, driven through J and K rather than through a data input. A part that toggles correctly but fails to hold is a real failure mode on a J-K, and it shows up as a counter that runs faster than the clock. The asynchronous set and reset need their own check, and the body marking separates the plastic DIP from the SOIC rows, one of which is obsolete.
The reference pages are the incoming inspection plan, date code management, and the pin to pin cross reference when a legacy board needs a second source for the J-K function.
Questions that come up on the 4027
Whether the part can be used as a divide by two with no external parts. It can, with J and K tied high and the clock as the input, which is the reason it appears in so many older divider chains.
Whether the drive figure of 1.5 mA is enough for a load. It is enough for CMOS inputs and for a transistor base through 1 k, and it is not enough for a relay or a lamp.
Whether the part can run from a 5 V rail driven by TTL. That is exactly the case the TTL input line in the table describes, and it is worth confirming against the direct current table rather than assuming either way.
Whether the obsolete SOIC row can still be sourced. It appears with a blank quantity and a Call TI instruction, so any stock is broker stock, and the active route is the BM96 reel or this plastic DIP.