Contact Us

TPS62065DSGR

Brand: Texas Instruments
Texas Instruments TPS62065DSGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62065DSGR — Power Management & Signal Chain | Superb Automation

TPS62065DSGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62065DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62065DSGR: 2.9 V to 6 V input 2 A step down converter at 3 MHz in a 2 mm by 2 mm SON

TPS62065DSGR is a 3 MHz synchronous buck with both FETs inside and a 600 mV reference, small enough that the inductor and two ceramic capacitors are the whole power stage in a WSON (DSG) body of 8 pins. It runs from 2.9 V to 6 V, delivers 2 A and holds the output adjustable from 0.8 V up to the input voltage. The high side FET is 120 milliohm at 3.6 V and the low side 90 milliohm, the forward current limit is 2.75 A typical, and the quiescent current is 18 microamp in power save mode.

Order code and package

Order code read outTPS62065 DSG R: converter TPS62065, DSG eight pin WSON, R large tape and reel
PackageWSON (DSG), 8 pins, 2 mm by 2 mm by 0.75 mm, part marking OFA, exposed pad on the underside
Carrier in the vendor addendumTPS62065DSGR at 3000 pieces on a large reel; TPS62065DSGT is the same part on a 250 piece small reel
Moisture levelLevel 2, 260 degrees peak reflow, one year floor life
Lead finishNickel palladium gold, quoted as NIPDAUAG
Temperature rangeJunction minus 40 to plus 125 degrees, storage minus 65 to plus 150
Absolute maximum7 V on the input pins, 150 degrees junction, with the switch node and the bootstrap capacitor rated for the swing of the switching waveform

Electrical parameters that decide the application

Input range2.9 V to 6 V, with the undervoltage lockout releasing at 1.95 V and dropping out at 1.78 V, so a 3.3 V or 5 V bus has a wide margin and a lithium cell can run down to the lockout
Output rangeAdjustable from the 600 mV reference up to the input voltage, with 100 percent duty cycle operation for the lowest dropout
Output current2 A continuous with a forward current limit of 2.3 A minimum, 2.75 A typical and 3.3 A maximum
Reference600 mV with plus or minus 1.5 percent feedback accuracy in forced PWM mode, and a deliberate 1 percent offset in power save mode that gives the voltage positioning behaviour
Switching frequency3 MHz nominal with a 2.6 to 3.4 MHz window, which is what allows a 1 microhenry inductor and a 10 microfarad output capacitor
High side FET120 milliohm typical and 180 maximum at 3.6 V, 95 typical and 150 maximum at 5 V
Low side FET90 milliohm typical and 130 maximum at 3.6 V, 75 typical and 100 maximum at 5 V
Quiescent current18 microamp typical in power save mode with no load and the part not switching, which is how a light load keeps its efficiency
Shutdown current0.1 microamp typical and 1 microamp maximum with the enable pin low
Power goodOpen drain output that releases at 95 percent of the reference and pulls low below 90 percent, so the window is 5 percent wide on each side and the delay is 5 microsecond
Mode pinSelects power save mode with automatic transition at light load, or forced fixed frequency PWM held by tying the pin to the input
Output dischargeAn internal resistor discharges the output when the enable pin is pulled low, so a rail does not float down after shutdown
Thermal150 degrees junction thermal shutdown with 10 degrees of hysteresis, and clock dithering to spread the switching noise rather than concentrate it at 3 MHz

Family members and the pins that change behaviour

TPS62065DSGRthe part on this page, adjustable output, 3000 pieces on a large reel, 2 mm by 2 mm WSON, marking OFA
TPS62065DSGTthe same part on a 250 piece small reel, which is what a prototype build normally needs
TPS62067the same family with a fixed 1.8 V output, a separate order code rather than a divider change
MODE pinpower save mode with automatic transition, or forced PWM at 3 MHz with a constant ripple, chosen by the state of one pin
AVIN and PVINseparate control and power input pins that must be connected together on the board, with the input capacitor placed at the power pin

Points to check before this part goes on a BOM

Running at 3 MHz is what makes a 2 mm by 2 mm converter possible, and it also moves the switching noise. A 1 microhenry inductor and a 10 microfarad output capacitor are enough at that frequency, so the whole power stage fits in the area of the package plus a couple of millimetres. The cost is switching loss, which is why the part is efficient at 2 A and merely acceptable at 20 mA unless power save mode is enabled.

Power save mode and forced PWM are two different products sharing one die. In power save mode the part skips pulses at light load, the quiescent current is 18 microamp and the feedback reference is deliberately offset by 1 percent, which lets the output sit slightly high at no load and gives the voltage positioning that improves a load step. In forced PWM the part switches at 3 MHz at every load, the ripple is constant and the accuracy is plus or minus 1.5 percent, which is what an RF or converter rail wants.

The 100 percent duty cycle capability is worth knowing about because it changes the usable input range. When the input falls close to the output the part stops switching and passes the input through, so a 3.3 V rail stays in regulation until the input is only the dropout above it. That is the reason the part is specified from 2.9 V in and is often used on a lithium cell that discharges to 3.0 V with a 2.5 V rail on the other side.

The current limit of 2.75 A typical against a 2 A rating is a narrower margin than a 3 A converter usually shows, and it is intentional for a part aimed at point of load rails with modest output capacitance. A rail with 100 microfarad of output capacitance at 1.2 V draws about 1.2 A of charging current at start up on top of the load, so the two together can approach the limit. That is worth checking before a board adds capacitance for a load step.

The VSON body at 2 mm square has almost no thermal mass, and the exposed pad is the only path. At 2 A and a 1.8 V output from 5 V the part dissipates roughly 0.35 W, most of it switching loss at 3 MHz, and the copper under the pad has to carry it. A board that runs 2 A continuously in a sealed enclosure at 70 degrees ambient needs the pad connected to a ground plane with several vias, not a single trace.

Clock dithering is a small feature with an EMC consequence. Instead of holding exactly 3 MHz, the oscillator moves slightly, which spreads the switching energy over a band and lowers the peak of the fundamental at the expense of a slightly wider noise floor. For a product that has to pass a conducted emissions limit this usually helps; for a receiver tuned near a harmonic of 3 MHz it can put noise where a clean clock would have put a null, so the receiver plan should be checked against the dither band.

Where this order code fits

Used on point of load rails in notebooks and handhelds, portable media players, DSP and FPGA supplies, and any board that needs 2 A from a 3.3 V or 5 V bus in a 2 mm square with a 1 mm height limit. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

What is the difference between power save mode and forced PWM? Power save mode skips pulses at light load, draws 18 microamp and offsets the reference by 1 percent for voltage positioning. Forced PWM holds 3 MHz at every load with a constant ripple and plus or minus 1.5 percent accuracy, selected by the MODE pin.

Can the output be set above 3.3 V? Yes, the output is adjustable up to the input voltage, and the part supports 100 percent duty cycle so a 3.3 V rail stays in regulation as the input falls to the dropout above it.

What inductor does it need? A 1 microhenry part is the usual choice at 3 MHz, paired with a 10 microfarad ceramic output capacitor. The high frequency is what keeps both small.

What is the current limit? 2.3 A minimum, 2.75 A typical and 3.3 A maximum, which is a narrow margin over the 2 A rating. A board with a large output capacitance should include the start-up charging current in that budget.

Does the output discharge after shutdown? Yes. An internal resistor discharges the output when the enable pin is pulled low, so the rail does not float down slowly.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop BOM Sourcing page sets out the checks that keep a substitute from failing on the bench.