Contact Us

TPS612994YBHR

Brand: Texas Instruments
Texas Instruments TPS612994YBHR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS612994YBHR — Power Management & Signal Chain | Superb Automation

TPS612994YBHR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS612994YBHR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS612994YBHR a 95 nanoamp boost with a 100 mA input current limit

The TPS612994YBHR is a synchronous boost converter in a 6 ball chip scale package measuring 1.2 mm by 0.8 mm, with a quiescent current of 95 nanoamp, an input range of 0.5 V to 5.5 V, an output range of 1.8 V to 5.5 V and an average input current limit of 100 mA. It is one member of the TPS61299x family, where the last digit of the part number sets the input current limit and the A suffix changes the behaviour at shutdown.

The family exists for coin cell and alkaline products that have to run for years. A 95 nanoamp idle current is below the self discharge of most coin cells, so the converter stops being the limiting factor in the shelf life calculation. The input current limit then protects the cell from the voltage sag that a burst load would otherwise cause, which is what ends the life of a coin cell product long before its capacity is used.

Start up is guaranteed from 0.7 V on the non-A members, and operation continues down to 150 mV while the input stays above 0.7 V. The part switches between a normal mode and a snooze mode, and the output accuracy in snooze is quoted in millivolts rather than per cent, because the load in that state is a few microamps.

Key parameters from the SLVSGS9G document

Input range0.5 V to 5.5 V, start up from 0.7 V on this member
Output1.8 V to 5.5 V, set by an external divider
Input current limit80 mA minimum and 100 mA maximum, which is what the 4 digit identifies
Quiescent current95 nanoamp typical into the input pin, 4 nanoamp into the output pin
Shutdown60 nanoamp into the input pin with the enable low, true shutdown on this member
SwitchingNormal mode for load steps, snooze mode for microamp loads
ProtectionThermal shutdown at 150 degrees with 20 degrees of hysteresis
Package6 ball chip scale, 1.2 mm by 0.8 mm, YBH body, 6000 pieces on a large reel, moisture level 1

The current limit ladder is the family

The family covers 5 mA, 25 mA, 50 mA, 100 mA, 250 mA, 500 mA, 1.9 A and 1.2 A input limits in the same die and the same package, and the four digit in the part number is the only difference. That is a useful selection tool: the same board can be built for a coin cell product and for a lithium cell product by changing the order code, and the current limit protects the smaller cell without a software change.

The A suffix is a behavioural difference at shutdown rather than a current difference. The plain member has true shutdown, which isolates the output from the input, and the A member forces the output to pass through the input instead. A product that has to keep a rail alive when the converter is disabled needs the A member, and a product that has to guarantee no leakage needs the plain one.

The 4 nanoamp output pin quiescent current is the number that matters when the output is held by another source. With the converter in snooze and the output biased externally, the part draws almost nothing from that rail, so it does not discharge a backup battery.

Where this part fits

Coin cell sensors, energy harvesting nodes, medical patches and any product where the idle current has to be below a microamp. Our desk keeps the boost cross reference and the family ladder, see power management cross reference and one stop BOM sourcing.

What to check before a purchase order

The last four digits set the input current limit, and a wrong digit is a working board with the wrong protection. A 100 mA part on a coin cell lets a transmit burst pull the cell below its cut off, and a 5 mA part on a lithium cell limits a load that should have been allowed to draw more. Confirm the digit against the cell datasheet rather than against the previous board.

The 6000 piece reel is larger than the usual 3000, so a prototype order either takes a full reel or a cut tape, and the chip scale body at 1.2 mm by 0.8 mm cannot be reworked by hand. Plan the assembly and the inspection around that. See incoming inspection plan for the receipt check on a 6 ball body.

Questions that come up on this part

Can it start from a 0.5 V input, is the first question, and the answer is that 0.5 V is the operating floor while 0.7 V is the guaranteed start up. A cell that has discharged to 0.6 V will not start the converter even though the input range says 0.5 V. The second question is whether 95 nanoamp includes the feedback divider. It does not, and a divider that draws a microamp will dominate the budget, which is why the family is normally used with an internal or a very high impedance divider setting.

The third question is about the 100 mA limit and the output current. At 0.9 V in and 3.3 V out the input current is about four times the output, so a 100 mA input limit supports roughly 20 mA at the output, less the efficiency. The limit is on the input, not on the load.