TPS61081DRCR
Product Specifications
TPS61081DRCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS61081DRCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS61081DRCR: 27 V boost converter with a 1.3 A integrated switch for instrumentation and display rails
TPS61081DRCR is a fixed frequency boost converter that integrates the power switch, the rectifier diode and an input to output isolation FET in a VSON body of 10 pins. It runs from 2.5 V to 6 V and boosts to as much as 27 V, and the vendor quotes 12 V at 400 mA and 24 V at 170 mA from a 5 V input as typical operating points. The FSW pin picks the switching frequency, a logic high gives 1.2 MHz and a logic low gives 600 kHz, and the feedback reference sits at 1.229 V typical.
Order code and package
| TPS61081DRCR | 10-pin VSON (DRC), 3.00 mm by 3.00 mm with thermal pad, large reel |
| TPS61080DRCR | same body and pinout, 0.5 A switch, the lower current member of the family |
| Switch current limit, TPS61081 | 1.3 A minimum, 1.6 A typical, 2.0 A maximum |
| Feedback reference | 1.204 V minimum, 1.229 V typical |
| Operating ambient temperature | -40 C to 85 C |
Electrical parameters that decide the application
| Input voltage range | 2.5 V to 6.0 V |
| Output voltage | up to 27 V, set by the feedback divider |
| Switching frequency | 1.2 MHz with FSW high, 600 kHz with FSW low |
| Switch current limit, TPS61081 | 1.3 A minimum, 1.6 A typical, 2.0 A maximum |
| Feedback regulation voltage | 1.204 V minimum, 1.229 V typical |
| Soft start bias current | 5 uA typical out of the SS pin, ramp time set by the capacitor to ground |
| Undervoltage lockout | 1.65 V typical, with 50 mV of hysteresis |
| Peak efficiency | up to 87 per cent at the vendor operating points |
| Output capacitor, recommended | up to 30 uF, a ceiling added in the third revision of the document |
What separates the two members of the family
| TPS61080 | 0.5 A switch, for loads up to roughly 100 mA at 12 V from a 3.6 V cell |
| TPS61081 | 1.3 A switch, the row on this page, for the 250 mA class 5 V to 12 V rail |
| FSW pin high | 1.2 MHz, the smaller inductor of the two options, 4.7 uH in the vendor example |
| FSW pin low | 600 kHz, the larger inductor, 10 uH, and lower switching loss at heavy load |
| Isolation FET | opens to separate output from input on a short circuit and while the part is shut down |
| FB pin as current source | the same pin can sit on a low side sense resistor to regulate output current |
| Protection set | cycle by cycle current limit, output overvoltage, thermal shutdown, undervoltage lockout |
Points to check before this part goes on a BOM
The 27 V output ceiling is a switch and diode rating, not a free choice of rail. The isolation FET, the internal diode and the 1.3 A switch all sit between the input and that ceiling, and the useful output power falls as the ratio climbs because the switch has to carry the inductor current for a longer part of each cycle. A 24 V rail from a 3.6 V cell is close to the practical limit of the 1.3 A member and needs the current budget worked out before the inductor is chosen.
The rectifier is inside the package, which is the reason the parts count is low, but it also means the forward drop is fixed and cannot be traded for a synchronous switch. At 24 V and 170 mA the diode carries the full output current during the off time, and that loss is part of the 87 per cent figure the vendor quotes. A program that needs more than that from a 3.6 V input is looking at a different family, not a different setting.
The isolation FET is the feature that separates this part from a plain boost regulator. On a short circuit the switch opens and disconnects the output from the input, so a failed load does not drag the battery or the upstream rail down with it. The same FET opens in shutdown, which is why the shutdown current stays low, and it is also why the output falls to zero rather than to one diode drop when the enable pin is pulled low.
After a short circuit clears, the part does not simply resume. The document describes a restart sequence in which the regulator starts up, reaches regulation, and then goes back into shutdown if the short circuit limit is reached again. A load that draws a hard fault intermittently will therefore show a hiccup pattern on the rail, and a controller monitoring that rail has to treat the pattern as a fault rather than as a slow start.
Soft start is a capacitor on the SS pin with a 5 uA typical bias current, and the ramp is a straight line from that current and the capacitor value. Without the capacitor the part starts into whatever inrush the output capacitors present, and on a 27 V rail with 30 uF of output capacitance that inrush can trip the current limit before the output reaches regulation. The capacitor is a 0402 part on most boards and there is no reason to leave it out.
The output capacitor has a stated ceiling of 30 uF. That ceiling is not a stability limit in the usual sense, it is the point at which the inrush at start up exceeds what the current limit allows, so a larger capacitor does not buy a quieter rail, it buys a part that fails to start. Where a large output capacitor is unavoidable, the soft start capacitor has to be scaled with it and the start up then measured on the bench.
The feedback node also accepts a current sense resistor on the low side. In that configuration the part regulates current instead of voltage, which is how it drives a string of white LEDs for a flash or a backlight without a separate driver. The same order code covers both jobs, and the difference is only where the feedback divider or the sense resistor sits, so a single part number can serve two lines in the same factory.
The 1.2 MHz setting allows a 4.7 uH inductor and the 600 kHz setting wants about 10 uH. That is the whole trade: the higher frequency gives a smaller inductor and a faster loop but more switching loss, the lower frequency gives better efficiency and a larger part. On a 12 V rail at 250 mA the difference in efficiency is a few points, and on a thermally tight board those points decide whether the part needs a copper pour.
The undervoltage lockout sits at 1.65 V typical, well below the 2.5 V minimum operating voltage. That gap is deliberate: a transient dip on the input during a load step does not reset the converter, the part simply keeps switching with reduced headroom. A board that sits close to 2.5 V on a two cell alkaline pack will see the output sag before the lockout acts, and the sag is a function of the cell impedance, not of the part.
Thermal performance depends on the exposed pad. The package is 3 mm by 3 mm and the switch dissipates most of its heat through the pad into the copper underneath, so a pad that is not soldered, or a pad connected to a plane through a single via, turns a part that runs at 60 C into one that reaches thermal shutdown at half its rated output. The vendor drawing shows the pad geometry and the via pattern to copy.
Package marking does not carry the switch rating. The TPS61080 and the TPS61081 share the body, the pinout and the document, and the difference is inside. A line that buys both for different rails has to keep them apart by reel label and by the incoming inspection record, because a mixed reel will not show up until a 250 mA load fails to start on a board built with the 0.5 A member.
The vendor product folder for this device no longer resolves on ti.com, and the document is now reached as SLVS644E through distribution mirrors. That is the usual pattern for a part that has moved out of active production, so a program with a long build plan should ask for a last time buy or a forward position rather than assume the reel will be there next year. The part is still available and still orderable, but the supply is finite.
How the isolation FET changes a fault
A plain boost converter has a DC path from input to output through the inductor and the rectifier, so a shorted load pulls the input down to the short and the upstream regulator folds back with it. The isolation FET in this part breaks that path on a fault and in shutdown, which keeps the input rail alive for the rest of the product and lets a controller report a load fault instead of a supply collapse.
Where this order code fits
It sits between a battery or a 5 V rail and a rail that has to be higher than the input, on instrument front ends, TFT bias supplies and xDSL line cards, where the load is a few hundred milliamps and the input can be as low as two alkaline cells near the end of their life. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
Can the output be set to 24 V from a single cell? The vendor quotes 24 V at 170 mA from a 5 V input as a typical operating point, not from a single cell. From a 3.6 V cell the switch current for the same output power is much higher and the 1.3 A limit is reached earlier, so a 24 V rail from one cell is a low current rail, and the exact current has to be taken from the efficiency and current limit curves rather than from the headline number.
What happens when the load is shorted? The isolation FET opens and separates the output from the input, which protects both the part and the upstream source. The output stays down until the fault is removed, and on a repeated fault the part goes through a start up and shutdown cycle rather than holding a limited current into the short.
Does the frequency setting change the order code? No. The FSW pin sets the frequency on the board, so one order code covers both 1.2 MHz and 600 kHz operation. Only the inductor and the compensation of the surrounding circuit change, and the pin is a logic input that can be tied high or low.
Why is there a maximum output capacitor value? Because the part has a fixed current limit and no separate inrush control. A capacitor above the stated ceiling draws more than the limit current while it charges, so the output never reaches regulation and the part keeps restarting. The ceiling is a start up limit rather than a stability limit.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.