Contact Us

TPS7A1901DRBR

Brand: Texas Instruments
Texas Instruments TPS7A1901DRBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A1901DRBR — Power Management & Signal Chain | Superb Automation

TPS7A1901DRBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A1901DRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A1901DRBR: 40 V input, 450 mA low dropout regulator with power good and 15 uA quiescent current

TPS7A1901DRBR is an adjustable low dropout regulator that takes up to 40 V in, delivers 450 mA and draws 15 uA at light load in a SON body of 8 pins. The output is set between 1.5 V and 18 V by an external divider against a 1.208 V reference, and the dropout is 450 mV maximum at 400 mA. It also carries a power good output with a programmable delay and is stable with ceramic output capacitors from 10 uF to 500 uF.

Order code and package

TPS7A1901DRBR8-pin SON (DRB), 3.00 mm by 3.00 mm with thermal pad, large reel, adjustable output
Order code patternTPS7A19XXYYYZ, where 01 in the voltage position means adjustable
Fixed voltage optionsthe same document covers fixed rows between 1.5 V and 18 V
Operating junction temperature-40 C to 125 C
Output capacitor range10 uF to 500 uF above 2.5 V out, 22 uF to 500 uF below 2.5 V out

Electrical parameters that decide the application

Input voltage4 V to 40 V when the output is at or below 3.5 V, otherwise output plus 0.5 V
Output voltage, adjustable1.5 V to 18 V set by the divider
Output current450 mA
Feedback reference1.208 V typical
Quiescent current15 uA typical, 25 uA maximum at 18 V in
Dropout at 400 mA240 mV typical, 450 mV maximum
Dropout at 200 mA160 mV typical, 300 mV maximum
Ripple rejection60 dB at 100 Hz with a 22 uF output capacitor at 100 mA
Power good thresholdprogrammable delay, output in regulation flag

Behaviour that matters on a wide input rail

Surge ride throughthe regulator holds regulation through a transient on the input rather than passing it on
Undervoltage lockoutthe output turns off below the lockout and comes back when the input recovers
Thermal shutdownthe pass element turns off when the junction limit is reached
Overcurrent protectionthe output current is limited rather than latched
Power good delaya capacitor on the delay pin holds the flag off until the output has settled
Enable pinthe part can be sequenced from a controller instead of following the input rail

Points to check before this part goes on a BOM

The input range above 3.5 V out is not 4 V to 40 V, it is output plus 0.5 V to 40 V. A 12 V rail from a 12 V battery therefore needs headroom that a discharged battery does not have, and the regulator drops out with the output following the input down. That behaviour is graceful on an instrument that only needs the rail while the battery is above 11 V, and it is a fault on a product that has to hold 12 V to the last amp hour.

The 15 uA quiescent current is what makes the part usable on an always on rail. It is also the number that gets wasted by the feedback divider. A divider that draws 100 uA to keep the reference noise low costs more than six times what the regulator itself draws, so the divider belongs at the highest value the feedback bias current allows, and the 1.208 V reference with a 25 uA maximum ground current sets the ceiling.

The dropout is quoted at two currents for a reason: at 400 mA it is 450 mV maximum and at 200 mA it is 300 mV. A product that needs 3.3 V from a 4 V rail has 700 mV of headroom at full load and is fine, while the same product asked to deliver 3.3 V from a 3.8 V rail is inside the dropout window at half load and outside it at full load. The current at which the rail falls out of regulation is the number to find on the curve.

The output capacitor range is not a suggestion. Below 2.5 V out the minimum is 22 uF because the loop gain falls with the output voltage and a smaller capacitor leaves the loop underdamped. Above 2.5 V the minimum drops to 10 uF. A board that uses one 10 uF capacitor across both a 1.8 V and a 3.3 V rail has one rail that is stable and one that rings on a load step.

Ceramic capacitors lose capacitance with bias voltage, and a 10 uF 25 V part at 20 V can be half its nominal value. On a 40 V input rail the derating is severe enough that the effective capacitance falls below the minimum the loop needs. The number to work against is the capacitance at the actual bias, taken from the capacitor vendor curve, not the value printed on the reel.

The power good output with a programmable delay is there for sequencing. A processor that is released before its rail has settled reads a wrong value out of flash, and the failure looks like a software bug. A capacitor on the delay pin holds the flag off for a time set by the board, which is the cheapest way to order two rails without a supervisor.

The part behaves as a simple surge limiter on a wide input rail because it holds regulation while the input moves. That is useful on a meter or a power tool that sees a inductive kick on the supply, and it is not the same as a transient suppressor. The pass element sees the full input to output difference as heat during the event, so the duration of the transient and the thermal mass of the board are part of the calculation.

The 3 mm by 3 mm SON has an exposed pad and the thermal resistance from junction to pad is what sets the dissipation limit. At 40 V in and 3.3 V out at 100 mA the part dissipates 3.7 W, which no 3 mm package survives. A wide input rail with a low output voltage is the wrong application for a linear regulator, and the arithmetic has to be done before the part is chosen rather than after the first board overheats.

The enable pin allows the rail to be sequenced, and it also allows the regulator to be shut down while the input stays alive. In shutdown the output is discharged through the internal path, so a rail that is turned off does not hold a capacitor charge into a load. That matters on a product that powers a sensor from the rail and expects the sensor to be off when the rail is commanded off.

The reference is 1.208 V, which sets the lowest adjustable output at 1.5 V because the divider cannot be taken below unity gain with the recommended values. A rail below 1.5 V needs a different part from the same family, not a different resistor pair, and the fixed voltage rows in the same document stop at the same place.

The part has no output discharge resistor beyond the path that is active in shutdown, so a rail that is switched off by pulling the enable pin falls at a rate set by the load. A load that is itself off draws nothing and the rail can sit at a residual voltage for seconds. A product that requires the rail to be at zero before the next power up needs a discharge path on the board.

The 40 V rating is an operating rating, and the absolute maximum is higher, but a supply that rings above 40 V during a load dump will still damage the part. The input capacitor placement and the series impedance of the harness decide how much of that ring reaches the pin. On a 24 V industrial rail the input capacitor is not optional and its voltage rating should carry the ring, not the nominal rail.

Where this order code fits

It sits between a 12 V or 24 V rail and the low voltage logic on a meter, a motor drive or an access control unit, where the input moves over a wide range and the logic rail has to stay quiet. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.

Questions buyers ask

What sets the output voltage? An external divider against the 1.208 V reference, so any voltage between 1.5 V and 18 V is available from the one adjustable order code. The fixed voltage rows in the same document cover the common rails without a divider.

How much current can it deliver at 3.3 V from 4 V? 450 mA is the rated current and the dropout at 400 mA is 450 mV maximum, so a 4 V input leaves 700 mV of headroom at full load. Anything closer than that puts the part in dropout and the output follows the input down.

Does it need a minimum load? No. The part is stable with ceramic output capacitors and holds regulation at no load, which is what the 15 uA quiescent current is for. The feedback divider is the only standing load the rail has to supply.

What is the power good output for? It flags that the output is in regulation, with a delay set by a capacitor, so a processor can be held in reset until the rail has settled. It is a sequencing signal, not a precision monitor.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.