TPS65150PWPR
Product Specifications
TPS65150PWPR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS65150PWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS65150PWPR: compact LCD bias supply with three rails and a VCOM buffer
TPS65150PWPR is a single chip bias supply that generates the positive, negative and common voltages a TFT panel needs in a HTSSOP body of 24 pins. One boost converter makes the main positive rail up to 15 V at better than 1 per cent accuracy, two charge pump drivers make the gate positive and gate negative rails, and a buffer drives the panel common voltage. The input takes 1.8 V to 6 V, and power on sequencing for the two gate rails is set by external components rather than by firmware.
Order code and package
| TPS65150PWPR | 24-pin HTSSOP (PWP), 2000-piece large reel, marking TPS65150, -40 C to 85 C |
| TPS65150PWP | 24-pin HTSSOP (PWP), 60-piece tube |
| TPS65150PWPG4 | 24-pin HTSSOP (PWP), 60-piece tube, green row |
| Second body | 24-pin VQFN, 4.00 mm by 4.00 mm, for the footprint limited case |
| Moisture sensitivity | Level-2-260C-1 YEAR, NIPDAU finish |
Electrical parameters that decide the application
| Input voltage range | 1.8 V to 6 V, absolute maximum 15.5 V on the input pin |
| Main boost output | up to 15 V, accuracy better than 1 per cent |
| Boost switch | 2 A internal MOSFET switch, 2.5 A current limit |
| Supply current, not switching | 1500 uA |
| UVLO on the input | 1.6 V falling, 1.7 V rising |
| Logic thresholds on the control pin | 1.6 V high, 0.4 V low |
| Thermal shutdown | 155 C |
| Operating junction temperature | -40 C to 125 C |
| Package thermal | 24-pin HTSSOP, 7.80 mm by 4.40 mm, exposed pad |
The four outputs and what sets them
| V(VS), main rail | boost converter, up to 15 V, set by the feedback divider |
| V(VGH), gate positive | regulated positive charge pump driver, set by its own divider |
| V(VGL), gate negative | regulated negative charge pump driver, set by its own divider |
| V(VCPI), second positive | positive charge pump driver for the extra gate level |
| V(COM), common | integrated buffer, no external op amp needed |
| Sequencing | adjustable power on order for the two gate rails, set by external parts |
Points to check before this part goes on a BOM
The input range of 1.8 V to 6 V is what makes this part interesting for notebook and monitor panels, where the only rail available before the panel comes up is a 2.5 V or 3.3 V logic rail. The whole bias supply therefore runs from the rail that is already there, and no separate boost stage is needed ahead of it.
The main boost is quoted at better than 1 per cent accuracy up to 15 V. For a panel, that accuracy is what keeps the source driver linear range centred, and a rail that drifts shows up as a shift in the grey scale rather than as a visible fault, which is why the tolerance is tighter here than on a general purpose converter.
The 2 A internal switch and the 2.5 A current limit set how large a panel the part can feed. A small notebook panel draws tens of milliamps on the source rail, a monitor panel draws more, and the switch rating together with the inductor decides where the boundary sits. The limit is a current limit, not a foldback, so a short on the source rail holds 2.5 A until the thermal path gives up.
The two gate rails come from charge pump drivers with external diodes and capacitors, and their levels are set by dividers. That is deliberate: the positive gate rail for a panel is often 15 V to 20 V above the source rail and the negative rail is several volts below ground, and no single inductor converter can make both without extra windings.
Sequencing is adjustable with external parts, and the order matters. If the gate positive rail comes up before the source rail, the panel transistors are stressed; if the negative rail comes up last, the panel shows a flash. The part handles the order itself once the external components are chosen, so the sequence is fixed by hardware and not by a firmware delay that can change.
The shutdown latch monitors all three outputs and latches the whole supply off when one of them falls below its power good threshold. That protects the panel from a half powered state, and it also means a single marginal output takes the whole display dark rather than producing a degraded picture.
Supply current with the device not switching is 1500 uA, which is high for a bias supply and is the price of the four output stages and the buffer. On a product that must meet a standby budget, the bias supply has to be disabled rather than idled, and the enable pin has to be driven from the system controller.
The undervoltage lockout sits at 1.6 V falling and 1.7 V rising, low enough to work from a 1.8 V rail with almost no margin. A rail that sags below 1.7 V during a load step will drop the whole bias supply, so the 1.8 V rail feeding it needs its own stability margin rather than the lockout's.
The 24 pin HTSSOP body is 7.80 mm by 4.40 mm with an exposed pad, and it carries four switching or charge pump stages plus a buffer. The pad has to be soldered to a copper area, and the input capacitor has to be close to the input pin, because the boost switch current and the charge pump currents share that pin.
One addendum detail is worth checking on receipt: the PWP rows for the PWPR order code appear twice in the vendor table, once with a 60-piece tube quantity and once with a 2000-piece large reel quantity. The part is the same, but a purchase order that names only the code without the reel size can be shipped either way, and the line has to know which it is receiving.
The common voltage buffer drives the panel backplane, which looks like tens of nanofarads of capacitance, and the two things to check against the panel are the buffer's drive current and its stability into that load rather than the converter ratings. A buffer that is stable into a resistor but rings into a panel shows up as a vertical band on the picture, which is usually blamed on the panel and is actually the bias supply.
Where this order code fits
It makes all the bias rails for a TFT panel in a notebook, a monitor, a car navigation display or an industrial terminal, from the 3.3 V or 5 V rail that is already on the board, without a second inductor for the gate rails. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
Can it drive a 15 inch panel? It depends on the panel current on the source rail. The boost switch is 2 A and the current limit is 2.5 A, which covers notebook and monitor panels; the panel current at the highest brightness is the number to check against the switch rating and the inductor.
Does it need an external op amp for VCOM? No. The common voltage buffer is inside the part, which is one of the reasons the solution stays compact. The buffer's output current and its load range are in the electrical table and should be checked against the panel input.
How is the power on order set? By external components on the sequencing pins, not by firmware. Once those parts are chosen the order is fixed, so a change of order means a change of components and a re qualification of the panel bring up.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.