Contact Us

TPS564242DRLR

Brand: Texas Instruments
Texas Instruments TPS564242DRLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS564242DRLR — Power Management & Signal Chain | Superb Automation

TPS564242DRLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS564242DRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS564242DRLR: 4 A synchronous buck, 3 V to 16 V input, 1.2 MHz, Eco-mode, SOT-563

TPS564242DRLR is a 4 A synchronous step down converter in a 1.6 mm by 1.6 mm six pin body, running at 1.2 MHz from a 3 V to 16 V input in a SOT-563 body of 6 pins. The switches measure 28.8 milliohm on the high side and 15.4 milliohm on the low side at 25 degrees, which is what allows 4 A in this footprint. The reference is 0.6 V with one per cent accuracy at 25 degrees, the quiescent current is 120 microamp in Eco-mode, and the fixed soft start is 1.39 ms. Control is D-CAP3, so the loop needs no external compensation, and the part supports up to 95 per cent duty cycle.

Order code and package

TPS564242DRLRActive, SOT-5X3 (DRL) body, 6 pins, 4000 pieces on a 180 mm reel, marking 4242
TPS564247DRLRthe forced continuous member, same body and same reel, higher quiescent current
TPS564242DRLR.AActive, same body and same 4000 piece reel with a different material row
Temperature rangeminus 40 to 125 degrees junction
Pin outsix pins, with separate analog and power grounds brought out

Electrical parameters that decide the application

Input voltage3 V to 16 V
Output voltage0.6 V to 7 V, set by a divider into the FB pin
Output current4 A continuous
Switch resistance28.8 milliohm high side, 15.4 milliohm low side at 25 degrees
Switching frequency1.2 MHz fixed
Reference0.6 V, one per cent at 25 degrees, 1.5 per cent over temperature
Quiescent current120 microamp in Eco-mode, 400 microamp in the forced continuous member
Current limit and timingvalley current setpoint around 7.5 A, 50 ns minimum on time, 1.39 ms soft start

Family variants and how they differ

TPS564242Eco-mode at light load, the string on this page
TPS564247forced continuous at light load, same rating and same body
Family4 A, 5 A and 6 A members share the pin out, so a rail can grow without a board change
Duty cycleup to 95 per cent, which is what allows a 5 V to 4.5 V rail
GroundsGND and AGND are separate pins and are joined at one point on the board

Points to check before this part goes on a BOM

Fifteen milliohm on the low side at 4 A is the number that carries this part. The low side conducts for most of the cycle at a low duty ratio, so its resistance dominates the conduction loss in a 12 V to 1.2 V rail. At 4 A it dissipates about 0.25 W while the high side dissipates about 0.13 W at a 10 per cent duty cycle. In a 1.6 mm body that is the difference between a working rail and a thermal foldback.

A 1.2 MHz switching frequency keeps the inductor small and the loss real. At 4 A and 1.2 MHz the ripple current in a 1 microhenry inductor is about 1 A, which is manageable for a small shielded part. Raising the frequency to shrink the inductor further increases the switching loss, and lowering it increases the ripple and the output capacitance needed. The fixed frequency is a compromise chosen for a dense board.

Three volts input is the lowest in this family and it changes what the part can do. A 3.3 V bus with a 10 per cent tolerance reaches 2.97 V, which is below the floor, so a 3.3 V rail cannot be used as the input for a 3.3 V input part at its tolerance limit. A 5 V bus is comfortable and a 12 V bus is the intended case. A 16 V ceiling excludes a 24 V bus.

Separate analog and power grounds are a feature that requires discipline. The two pins have to be joined at a single point, usually under the part, and the feedback divider has to return to the analog pin. A board that joins them at the input capacitor instead puts the switching current through the reference return and the output shows switching noise on a DC measurement.

Eco-mode at light load is the right choice for a standby rail and the wrong one for an analog load. Below about 300 mA the converter skips pulses and the ripple becomes a low frequency wave. A processor rail does not care, and a rail feeding an ADC does. The forced continuous member draws 400 microamp instead of 120 and holds the ripple at 1.2 MHz, which is what an analog load needs.

The valley current limit sits at about 7.5 A, well above the 4 A rating. That is deliberate: a load step to 6 A for a few milliseconds does not trip the limit, which keeps a processor from resetting during a burst. It also means the part does not protect a downstream short quickly, and the hiccup behaviour takes over once the output collapses.

A 4000 piece reel is the packing for this body. That is a full reel for a part used once or twice per board, so a prototype build leaves most of a reel in stock with a moisture clock running. The part is Level-1-260C-UNLIM on the base row, which means no floor life limit, and that is worth checking on any alternative source.

The 1.39 ms soft start is fixed and it is short for a large output bank. A 470 microfarad output charges to 1.2 V in that time only if the current limit allows it, and the part will run at the valley limit for part of the ramp. The output arrives, but the input supply sees a current step. A board with a large bank has to check the upstream converter against that step.

Wettable flanks are absent on this body, and that is normal for SOT-563. Inspection is by X-ray or by a visual check of the fillet, and a customer with an automotive process control plan may need the larger body with wettable flanks. That is a packaging question rather than an electrical one, and it is decided before the board is released.

What to confirm before this part goes on a purchase order

State the input bus and the output voltage. The 95 per cent duty cycle allows a 5 V to 4.5 V rail and the 3 V floor excludes a 3.3 V bus at the bottom of its tolerance, so the bus decides whether the part works at all.

Say whether the rail sleeps. Eco-mode and forced continuous conduction are different strings with different quiescent current, and the choice depends on the load rather than on preference.

Where this order code fits

It makes a 1.8 V or 3.3 V rail at 4 A from a 12 V or 5 V rail in a router, a set top box or an industrial controller, in a body small enough for a dense board. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it produce 1.2 V at 4 A from a 12 V input? Yes, and that is the intended operating point. The duty cycle is 10 per cent, the minimum on time of 50 ns is not reached at 1.2 MHz, and the low side switch carries most of the current. The thermal calculation, not the duty cycle, is the limit in the small body.

Does it need an external compensation network? No. D-CAP3 is compensated internally and there is no COMP pin. The output capacitor is part of the loop, so its value after bias derating has to stay within the range the application section gives, and a much larger capacitor changes the transient response.

What is the difference between this part and the 247 suffix? Light load behaviour. The 242 skips pulses and draws 120 microamp at light load, and the 247 keeps switching and draws 400 microamp. The full load behaviour and the current limit are the same, and the two are interchangeable only if the light load ripple does not matter.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.