Contact Us

DRV8428PPWPR

Brand: Texas Instruments
Texas Instruments DRV8428PPWPR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8428PPWPR — Power Management & Signal Chain | Superb Automation

DRV8428PPWPR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8428PPWPR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8428PPWPR: a 33 V stepper driver that needs no sense resistors

The DRV8428PPWPR is the HTSSOP body of the DRV8428, a bipolar stepper driver that carries two N-channel H-bridges, a microstepping indexer and the current sense circuit on one die. The sense resistors that normally sit under each bridge are gone: the driver measures the winding current internally, so the two power resistors and the two sense traces they need disappear from the board. The vendor quotes plus or minus 6 percent full scale current accuracy for that internal arrangement, which is the number to compare against a resistor based driver before swapping one for the other.

The supply window is the point that decides most of its use. The operating range is 4.2 V to 33 V with an absolute maximum of 35 V, so a 24 V rail sits comfortably inside it and a 36 V rail does not. The parametric row on the vendor page lists the minimum as 4.5 V rather than 4.2 V, and the two figures describe the same part, so a system that has to run at the bottom of the window should be checked against the addendum row for the exact order code rather than against the headline.

Current is quoted three ways and all three matter: 1.7 A peak per bridge, 1 A full scale, 0.7 A rms. The on resistance is 1500 mOhm high side plus low side at 24 V and 25 C, which is the highest figure in the 1/256 microstepping family and the reason the part sits at the low current end of it. At 0.7 A rms the conduction loss per bridge is roughly 0.7 squared times 1.5, about 0.74 W for both phases together on a full step, and that is the number that sets the copper area under the pad.

Microstepping runs to 1/256 with a plain STEP and DIR interface, so no serial bus is needed and no register map has to be loaded at power up. Off time is selectable at 7, 16 or 32 microseconds, sleep current is 2 microamps, and spread spectrum clocking is included to move switching energy away from a single frequency. The fault pin is combined with the enable pin on this part, which is one pin fewer than the SPI versions of the same family and one behaviour more to check in software.

Key data for the DRV8428PPWPR

Operating supply4.2 V to 33 V, absolute maximum 35 V
OutputsTwo H-bridges, 1/256 microstepping indexer, STEP and DIR interface
Current1.7 A peak, 1 A full scale, 0.7 A rms per bridge
On resistance1500 mOhm high side plus low side at 24 V and 25 C
Current senseInternal, no external sense resistors, plus or minus 6 percent full scale
Decay modesSmart tune and mixed decay
Off time7, 16 or 32 microseconds, set by pin
Sleep current2 microamps typical
ProtectionUndervoltage lockout, overcurrent, thermal shutdown, combined enable and fault pin

Body, packing and marking data

Body in this code16-pin HTSSOP, the PWP outline, 5.00 mm by 6.40 mm, 32 mm squared with a PowerPAD
Other body16-pin WQFN, the RTE outline, 3.00 mm by 3.00 mm, 9 mm squared
TemperatureMinus 40 C to plus 125 C operating
CarrierTape and reel; the count per reel is fixed per order code and is read from the vendor addendum row

Reading the code before you buy it

DRV8428 is the circuit, PWP is the 16-pin HTSSOP and the trailing R is the large reel. The same circuit in the 3 mm square QFN carries RTE instead, and the two are not interchangeable on the board: one has a 5 by 6.4 mm footprint with leads and the other is a 3 mm square with a thermal pad. Ordering the wrong letter is a re-spin of the copper, not a substitute part.

The 16-pin footprint is shared with a long list of TI stepper drivers, and the vendor publishes the ladder in its pin to pin table: DRV8428 at 1500 mOhm and 1 A full scale, DRV8436 at 900 mOhm and 1.5 A, DRV8424 and DRV8426 above that, then the 24 and 28 pin versions for higher current. That ladder is what makes this order code useful in a family of products: one board can carry the 1 A part in a small actuator and the 1.5 A part in a larger one without new tooling. Our pin to pin cross reference page lists the same check in the order we run it.

The letters after PWP do not encode a temperature grade on this part, because the whole family is published at minus 40 C to plus 125 C. What they encode is packing: bare PWP is the tube or tray form, and the R suffix is the reel. A line that runs a pick and place machine needs the R, and a prototype order often does not, which is the difference between two prices for what looks like the same part number.

Where the DRV8428PPWPR fits

Small steppers in laboratory instruments, valve actuators, peristaltic pumps and optical stages run between 0.3 A and 1 A per phase at 12 V or 24 V, and this is the band the part was built for. The internal sense is the practical advantage there: the two sense resistors are usually 0.1 to 0.2 Ohm power parts in a 1206 or larger body, they take board area next to the driver, and on a four layer board they are often the parts that force the thermal relief to be cut back.

Printers, card readers and vending mechanisms use the same driver for paper feed and for the shutter, and there the STEP and DIR interface is enough because the mechanism never needs to read back a register. Medical dosing pumps and laboratory sample handlers use it for the same reason, with the added requirement that the current accuracy of the internal sense is documented; plus or minus 6 percent full scale is the figure that goes into the tolerance stack for the dose.

Where the part does not fit is any rail above 33 V. A 36 V or 48 V stepper system has to move to the 48 V or 65 V members of the family, and that move also changes the pin count from 16 to 24 or 28, so the board is different. Our BOM shortage recovery page covers how we handle that when the 16-pin part is the one on shortage and the only alternative is a different body.

Questions we get on this code

Does the internal sense mean the current is fixed? No. The full scale current is set by the indexer and by the torque DAC bits where the part has them, and the internal sense only replaces the two external resistors. The accuracy figure of plus or minus 6 percent applies to that internal arrangement, and a board that needs tighter phase current has to accept the trim in software or move to a part that publishes a tighter number.

Can it run from a 12 V battery directly? The window starts at 4.2 V, so a 12 V lead acid pack that falls to 10.5 V under load stays inside it, and the 2 microamp sleep current makes it practical to leave the driver powered when the instrument is idle. What has to be watched is the inductive kick at the connector when the pack is unplugged, because 35 V absolute maximum is not a large margin over a 24 V rail with a long lead.

What is the difference against the SPI versions? The SPI versions add register access, stall detection, more decay options and a separate fault pin. This part gives STEP, DIR, three off time choices and the combined enable and fault pin. A mechanism that only needs to move and stop does not need the bus, and not loading a register map at power up removes a failure mode from the start sequence.

How is the reel count confirmed? We read the addendum row for the exact order code before quoting, because the count differs between the PWP and RTE bodies and between reel sizes. A quote that names a reel count without the addendum row behind it is a guess, and the guess usually surfaces at the pick and place machine.