Contact Us

DRV8263HQVAKRQ1

Brand: Texas Instruments
Texas Instruments DRV8263HQVAKRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8263HQVAKRQ1 — Power Management & Signal Chain | Superb Automation

DRV8263HQVAKRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8263HQVAKRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8263HQVAKRQ1: a 65 V, 28 A bridge for 24 V and 48 V automotive rails

The DRV8263HQVAKRQ1 is the wide voltage member of the automotive H bridge family, built for 24 V and 48 V systems. It runs from 4.5 V to 65 V with a 70 V absolute maximum, has 85 mOhm of combined on resistance, and drives up to 28 A. The H in the string is the hardware interface; the same die is offered with an SPI port for register level configuration and diagnostics.

The body is a 15-pin VQFN-HR at 3.5 mm by 6 mm, which is a small footprint for a bridge that has to hold 65 V. The thermal pad on the underside is the only path for the heat, so the copper under it is part of the current rating rather than a small detail of the board. The part is AEC-Q100 grade 1 and carries functional safety documentation.

Control modes cover the three ways a bridge is normally used: a single full bridge with PH/EN, a single full bridge with independent PWM inputs, and two independent half bridges. PWM runs to 100 kHz with automatic dead time insertion, which is the highest switching frequency in this family and the reason it is quoted for 48 V systems where the ripple current has to stay small.

Key data for the DRV8263HQVAKRQ1

Supply4.5 V to 65 V operating, 70 V absolute maximum on VM
On resistance85 mOhm high side plus low side
Current28 A maximum output, high-side mirror sense on IPROPI
InterfaceHardware pins, PH/EN, PWM or independent half-bridge mode
SwitchingPWM up to 100 kHz with automatic dead time, configurable slew rate and spread spectrum
DiagnosticsOn and off state load diagnostics, VM monitoring, overcurrent, overtemperature
QualificationAEC-Q100 grade 1, minus 40 C to plus 125 C ambient, functional safety compliant targeted

Body, packing and marking data

Body15-pin VQFN-HR with thermal pad, the VAK body, 3.5 mm by 6 mm
Carrier3000 pieces on a large tape and reel
FinishNickel palladium gold, moisture level quoted on the addendum row
Marking8263H plus the lot and date code on the reel label

Reading the code before you buy it

DRV8263HQVAKRQ1 reads as DRV8263, H, VAK and RQ1. The H is the hardware interface and the SPI variant of the same die carries a different letter in the same position, so the two are not interchangeable on a board that has already been wired for one of them.

The voltage is the reason to choose this part over the rest of the family. The DRV824x parts stop at 35 V operating, which covers 12 V and 24 V systems but not a 48 V rail with a load dump margin. This part covers 65 V, and the 70 V absolute maximum is what leaves room for the transient that a 48 V alternator or a contactor can produce.

One diagnostic detail is worth noting because it is easy to miss. Die temperature is reported on IPROPI on the SPI variant only. On the hardware variant in this string, the temperature information is limited to the thermal shutdown threshold and the fault pin, so a module that wants to derate before the shutdown needs the SPI version.

The independent half-bridge mode is worth a closer look because it changes what the part can drive. In that mode the two halves are no longer interlocked, so they can feed two separate loads that share a supply, such as a pump and a fan in the same housing. The current sense then reports whichever half is conducting, and the controller has to know which one it commanded, because the IPROPI pin carries one signal for both.

The 100 kHz switching ceiling is the other feature that separates this part from the 35 V family. At 48 V the ripple current in a small inductor is the limit on how much copper the mechanism can carry, so a higher switching frequency allows a smaller inductor or a lower ripple at the same inductance. The trade is switching loss, which at 65 V is a real number and not a footnote, so the frequency should be chosen against the total loss rather than against the ripple alone.

Where a 65 V bridge earns its place

48 V mild hybrid systems are the first case. An electric supercharger, a water pump or an active suspension actuator on a 48 V rail draws tens of amps, and the 100 kHz switching keeps the current ripple inside a small inductor. The 28 A maximum covers the transient and the derating curve sets the continuous figure.

24 V truck and bus loads are the second. A 24 V system with a load dump transient goes well above the nominal, and a 35 V part is too close to the edge. The 65 V window is the difference between a module that survives the test and one that has to be changed after it.

Industrial 48 V mechanisms are the third, where the automotive qualification is not needed but the voltage is. Buyers who need the qualification paper can check what the procurement route normally carries on the OEM procurement page, and a comparison against the 35 V family is on the power management cross reference page.

Questions we get on this code

The first question is whether 28 A is continuous. It is the die rating. At 85 mOhm the conduction loss at 28 A is 67 W, which no package can move, so the continuous current in a real module is set by the thermal path and typically lands between 8 A and 15 A depending on the copper and the airflow.

The second question is about the 100 kHz switching. It is available, but the switching loss at 65 V and 100 kHz in an 85 mOhm bridge is significant, so a build that needs the frequency should check the total loss rather than the conduction loss alone.

The third question is what happens with a 48 V rail during a load dump. The absolute maximum of 70 V is below a full load dump, so the module still needs a clamp. The part survives the inductive kick of its own load, which is a different event from a system level surge.

The fourth question is about the body. A 15-pin VQFN-HR at 3.5 mm by 6 mm is small for a bridge that has to hold 65 V, so the creepage between the high voltage pins and the logic pins is worth checking against the module clearance rules. The pad geometry assumes a reflow process with a controlled void rate, and a hand rework will not reproduce it.

The fifth question is about the half-bridge mode with two independent loads. Both halves work independently and the current sense reports the conducting half, but the interlock that prevents shoot-through no longer applies across the pair, so the loads have to be isolated from each other.