DRV777PWR
Product Specifications
DRV777PWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The DRV777PWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
DRV777PWR: seven low-side channels in a 16-pin TSSOP
The DRV777PWR is a seven-channel low-side driver in the 16-pin TSSOP body, built for relays, solenoids, unipolar stepper windings and lamps that a microcontroller cannot sink on its own. Each channel is an open drain output with an internal free-wheeling diode returned to the COM pin, so an inductive load is clamped inside the part instead of on the board. The inputs accept 1.8 V, 3.3 V and 5.0 V CMOS levels, which means a 1.8 V sensor hub and a 5 V logic board can both drive it without a level shifter in between.
Each channel sinks 140 mA with a 5.0 V logic input, and the typical output low at that current is 0.4 V. All seven channels can be tied in parallel to reach 1 A, which is the route for a single larger solenoid or a small DC motor. The COM pin carries the common cathode of the seven free-wheeling diodes and also sets the clamp rail, so the load supply has to stay inside the 20 V pull-up window.
The ESD cells are rated at 2 kV human body model and 500 V charged device model, and the input stage is built to survive a tri-state, which is the condition a micro leaves behind during a reset or a debug halt. That combination is why the part shows up on boards that get a connector to the outside world, where a cable can pick up noise while the controller is not driving anything.
This is the CMOS successor to the seven-channel Darlington arrays that have sat on relay boards for decades. Saturation voltage is far lower, the input current is far smaller, and every input carries an internal pull-down resistor, so a tri-stated micro leaves all seven outputs off rather than floating into a half-on state.
Key data for the DRV777PWR
| Channels | Seven low-side outputs, open drain, with the free-wheeling diodes commoned at COM |
| Sink per channel | 140 mA with a 5.0 V logic input, 0.4 V typical output low at that current |
| Paralleled output | 1 A with all seven channels tied together |
| Output pull-up | Up to 20 V at COM, which is the ceiling for the load supply |
| Logic interface | 1.8 V, 3.3 V and 5.0 V CMOS, internal pull-down on every input |
| Input filtering | RC snubber on each input to stop spurious switching on a noisy harness |
| Temperature | Minus 40 C to plus 125 C operating range |
Body, packing and marking data
| Body | 16-pin TSSOP, the PW body |
| Carrier | 2000 pieces on a large tape and reel |
| Finish | Tin plated leads, moisture level 1, 260 C unlimited floor life |
| Marking | DRV777 plus the date code and lot code printed on the reel label |
Reading the code before you buy it
DRV777PWR breaks into three pieces: DRV777 is the circuit, PW is the 16-pin TSSOP body, and R is the reel. There is no temperature suffix and no automotive suffix on this string, so the part is an industrial grade device with the minus 40 to plus 125 C range as its only grade.
One inconsistency is worth knowing before a purchase order goes out. The front page table of the vendor document pairs the DRV777PWR string with a 16-pin SOIC body and a 2500 piece reel, while the packaging addendum at the back prints TSSOP (PW) with 2000 pieces on a large tape and reel. The addendum is the page that the factory ships against, so 2000 on a reel is the figure to plan a line around, and the body on the reel label reads PW rather than D.
If a drawing or an approved vendor list still names a 16-pin SOIC, treat that as a separate line item and ask for the body to be confirmed in writing rather than assuming the two are interchangeable. The pin function order is the same seven inputs, seven outputs, ground and COM, but the footprint is not.
Where the seven channels earn their place
Relay banks are the classic case. A 12 V coil at 40 mA to 80 mA sits comfortably inside the 140 mA channel rating, the free-wheeling diode at COM removes the need for seven discrete diodes, and the internal pull-down keeps every relay released while the controller is in reset. Solenoid valves in water and gas meters follow the same pattern, with the caveat that the inrush of a solenoid is several times its hold current.
One detail that decides whether the board survives a field failure is the COM connection. The common cathode of the seven diodes has to reach the same supply that the loads pull from, and it has to be a short, wide trace, because every clamp current from seven relays returns through that one pin. A COM pin tied to a distant ground plane instead of the coil supply turns the internal diodes into a path that the die was not built for.
Unipolar stepper windings are the second case. Four of the seven channels drive the two centre-tapped windings, the remaining three stay free for a brake, a valve or an indicator, and the RC snubber on each input keeps a long ribbon cable from injecting false steps. Lamp and LED strings are the third, where the 0.4 V typical saturation at 140 mA keeps the dissipation low enough for a small board.
Paralleling is where an engineer has to do arithmetic rather than assume. Seven channels at 140 mA each add up to 980 mA, but the total is limited by junction temperature and by the absolute maximum current of the die, not by the sum of the channel ratings. A 1 A load on a single die in a TSSOP body at 85 C ambient needs the copper area checked before the number is put on a drawing. Buyers sourcing this class of part can start from the power management cross reference page, which maps the seven-channel driver families by channel count and current.
Questions we get on this code
The first question is always whether it drops into a board built for a seven-channel Darlington array. Electrically the function is the same, and the input pull-downs make the interface easier, but the body and the pin pitch have to be checked against the actual land pattern on the board rather than against the circuit symbol. The verification route we use is on the pin to pin cross reference page.
The second question is about a 24 V relay. The COM pin is rated to 20 V of output pull-up, so a 24 V coil is outside the window even though the channel current is small. A 24 V system needs a different device with a higher clamp rating, or a coil driver with an external diode.
The third question is why the channel is 140 mA when the older arrays are quoted at 500 mA. The Darlington array quotes a peak that it can only hold with a large voltage drop, and it dissipates most of the load power in the driver. The DRV777 quotes a saturation voltage at the rated current, which is the number that decides whether the part survives a warm enclosure.
The fourth question is about noise on the input harness. The RC snubber and the pull-down are both there for that reason, and the ESD cells are rated at 2 kV human body model and 500 V charged device model, which covers handling but not a lightning surge on a field cable. A relay board that leaves the building should still carry a TVS on the coil rail.
The fifth question is about the body on the reel label. Because the front page of the vendor document and the addendum disagree on SOIC against TSSOP, an incoming inspection plan that only reads the line item will pass a reel that does not fit the land pattern. The check is one photograph of the reel label against the drawing before the parts go to the line.