Contact Us

DRV8213DSGR

Brand: Texas Instruments
Texas Instruments DRV8213DSGR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

DRV8213DSGR — Power Management & Signal Chain | Superb Automation

DRV8213DSGR

Texas Instruments — Power Management & Signal Chain

Product Overview

The DRV8213DSGR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

DRV8213DSGR: a 4 A brushed driver in a 2 mm body with the current sense on a pin

The DRV8213DSGR is an H-bridge for brushed DC motors, solenoids and relays that runs from 1.65 V to 11 V and delivers 4 A peak. The combined high-side and low-side on resistance is 240 mOhm, and the tripler charge pump keeps the gate drive alive down to 1.65 V, which is what makes the part usable on a single lithium cell or on a 1.8 V rail that sags under load.

Current is measured internally by a mirror that feeds the IPROPI pin as an analogue voltage, so there is no shunt resistor and no sense amplifier to add. The GAINSEL pin picks between two gain ranges, which is how the part keeps accuracy down to 10 mA of average motor current without losing resolution at 2 A. A resistor from IPROPI to ground sets the voltage that the controller reads, and the VREF pin lets the part regulate current on its own during start-up and stall.

The sense output is a current, not a voltage, so a resistor from IPROPI to ground both converts it and sets the scale. That single resistor therefore decides the voltage the controller reads at 1 A and the current at which the internal regulation starts to fold the bridge back, which is why a value copied from a reference board without checking the intended limit gives a driver that limits at the wrong current.

The switching interface is a plain PWM pair with no register map, so a controller that has no spare serial port can still run the part. Up to 100 kHz of PWM is inside the range where the bridge current stays continuous at typical motor inductances, and the charge pump keeps the high side on at 100 per cent duty, which is what allows a locked rotor to hold full torque without a bootstrap refresh gap.

The 8-pin WSON body is 2.00 mm by 2.00 mm with a thermal pad, and the whole driver plus its charge pump fits under a motor connector. Sleep current is below 60 nA maximum, which matters in a meter or a lock that has to sit for years on a coin cell.

Key data for the DRV8213DSGR

Supply1.65 V to 11 V on VM, logic from 1.8 V, 3.3 V or 5 V
On resistance240 mOhm high side plus low side
Current4 A peak output, internal mirror sense, no external shunt
Sense outputIPROPI analogue voltage, GAINSEL chooses the range, usable down to 10 mA
RegulationVREF pin sets a current limit that works without the controller
SwitchingPWM interface up to 100 kHz, 100 per cent duty through the charge pump
ProtectionVM undervoltage lockout, auto-retry overcurrent, thermal shutdown

Body, packing and marking data

Body8-pin WSON, the DSG body, 2.00 mm by 2.00 mm with thermal pad
Carrier3000 pieces on a large tape and reel
FinishNickel palladium gold, moisture level 1, 260 C unlimited floor life
Sleep currentBelow 60 nA maximum, which is the figure a battery life calculation needs

Reading the code before you buy it

DRV8213DSGR is DRV8213, DSG and R. The DSG body is the 8-pin WSON and the RTE body is the 16-pin WQFN, and the difference is not only size. Stall detection and the configurable inrush time belong to the 16-pin RTE body, because both need the IMODE and the extra control pins that the 8-pin body does not have.

So a board that buys the DSG string gets current sense and current regulation, and does not get sensorless stall reporting. A board that needs the controller to be told the motor has jammed has to move to the RTE string and give up 1 mm of board space in each direction. That is the single most common order code mistake on this family.

The second thing to fix in writing is the sense gain. GAINSEL is a pin, not a register, so the two ranges are chosen by a level at the pin and the resistor at IPROPI has to be picked for the range that the controller software expects. A board built for one range and populated as if it were the other reads a current that is off by the gain ratio, and nothing in the register map shows it.

Where the 4 A driver earns its place

Battery powered instruments are the first case. A water or gas meter valve draws a short pulse of 200 mA to 400 mA, the driver sits in sleep at 60 nA for the rest of the month, and the IPROPI output tells the controller whether the valve actually reached its stop. A smart lock is the same pattern with a higher stall current.

Portable medical equipment is the second case. An infusion pump needs a current limit that holds the motor at a known torque rather than a known speed, because the tubing pressure decides the load. The VREF pin sets that limit without controller involvement, so a watchdog reset does not leave the motor running at full current. Component selection for that class of build is covered on the medical device component page.

The protection set is modest on purpose. There is no reverse battery protection on the supply pin, no charge pump fault flag and no separate overvoltage comparator on this member, so a product that can see a reversed battery, such as a tool with a removable pack, needs the reverse path handled outside the driver. A product on a fixed internal rail does not.

Small appliances, toys and point of sale printers are the third case. All three want the lowest part count, the 2 mm body and the 100 kHz PWM that keeps the audible whine above the range of the customer, and none of them want an external shunt.

Questions we get on this code

The first question is whether the 4 A figure is a continuous rating. It is a peak rating. Continuous current is set by the thermal pad, the copper under it and the ambient, and at 240 mOhm the part dissipates 0.24 W per amp squared, so 1.5 A continuous already asks for a solid ground plane.

The second question is how accurate the sense is at low current. The mirror is trimmed and the gain select extends the usable range down to 10 mA average, but the absolute error grows as a fraction of the reading below that. A stall threshold set at 20 mA is workable; a torque reading at 5 mA is not.

The third question is what happens on a short. The overcurrent protection is auto-retry, so the driver folds back and tries again rather than latching off. A machine that must not restart by itself needs a controller that counts the nFAULT edges and decides.

The fourth question is about second sources and cross references. The pinout is shared across the DRV821x family but not across every 8-pin brushed driver on the market, so the check belongs on the power management cross reference page before a substitution is written into a drawing.

The fifth question is whether the part can drive a relay coil rather than a motor. It can, and the internal bridge diodes clamp the coil on turn-off, but a relay that chatters needs the current regulation to hold the coil rather than the PWM to hold it, otherwise the armature buzzes at the switching frequency and the contact wears out early. A coil held by a regulated current also runs cooler than one held at full supply, which matters in a sealed enclosure.