Contact Us

TPS61163AYFFR

Brand: Texas Instruments
Texas Instruments TPS61163AYFFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS61163AYFFR — Power Management & Signal Chain | Superb Automation

TPS61163AYFFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS61163AYFFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS61163AYFFR: a dual channel white LED driver for a phone backlight that boosts from a single cell to 37.5 V, holds two strings to 1 per cent of each other and needs only 90 mV of headroom

TPS61163AYFFR is a boost converter with a 40 V switch on the die, two matched current sinks that set the string current from one resistor, and a one wire interface that writes a nine bit brightness code so the panel can dim without a PWM line in a DSBGA body of 9 pins. The YFF body is nine bumps on a 1.45 mm by 1.45 mm die, and the part exists so a phone backlight of ten LEDs in two strings runs from one cell with a single inductor.

Order code and package

Catalogue stringTPS61163AYFFR, where the A marks the 37.5 V overvoltage option and YFF is the nine bump die scale body
BodyDSBGA, YFF, nine bumps, 1.45 mm by 1.45 mm, 0.80 mm maximum height
Reel3000 pieces on a large tape and reel
Finish and moistureNIPDAU plating, level 1 at 260 C on the published row
Temperatureminus 40 to 85 C for the current accuracy specifications, with thermal shutdown at 160 C
Marking61162A on the body, the same marking as the 26.5 V member, so the reel label and not the package decides which one is on the line
DocumentSLVSC26B, November 2013, revised May 2024
StatusActive and in production on the addendum dated November 2025

Electrical parameters that decide the application

Input range2.7 V to 6.5 V, which covers a single lithium cell from full charge to cut off without a pre regulator
Switchan integrated 1.5 A, 40 V MOSFET with 0.25 Ohm of on resistance at 3.6 V in and a leakage of 1 uA at 35 V
Stringstwo current sinks of up to 30 mA each, which is ten LEDs in two parallel strings of five
Current accuracyplus or minus 2 per cent at full brightness and plus or minus 2.3 per cent at 25 per cent dimming, from minus 40 to 85 C
Matching1 per cent typical between the two strings, which is what keeps a white backlight from showing a colour shift across the panel
Headroom90 mV of voltage across the current sink, so the boost output sits just above the LED string rather than at a fixed high rail
Switching frequency1.0 to 1.5 MHz with 1.2 MHz typical, which allows a 4.7 uH inductor
Overvoltage37.5 V typical on this member, against 26.5 V on the 61162A, with the window 36 to 39 V
Protectionswitch current limit 1.0 to 2.0 A with a 0.7 A start up limit, a 5 ms half limit window, an open and short detection on each sink and a 4.2 to 5 V sink overvoltage point
DimmingPWM input to a 100 to 1 ratio and a one wire interface to nine bits of resolution, with the brightness set by the ISET pin voltage
Enable1.2 V high and 0.4 V low, with an 800 kOhm internal pull down, and 2.5 ms from the enable falling to shutdown
Thermal160 C shutdown with a 107 C per watt junction to ambient on a four layer board

How the two overvoltage options differ

TPS61163AYFFR37.5 V overvoltage, for a string of up to ten LEDs, marking 61162A, this page
TPS61162AYFFR26.5 V overvoltage in the same body and the same marking, for a shorter string where a lower clamp is safer
The ISET resistorsets the string current, with 1.229 V at full brightness and a 1030 current multiplier, so 20 uA through the resistor gives 20.6 mA per string
A single string driverone sink and one string halves the current and needs half the inductor, and cannot split a wide panel into two halves
A driver with a fixed outputa fixed boost rail wastes the difference between the rail and the string voltage in the sink, which at 90 mV of headroom is the whole efficiency argument
A charge pumpa switched capacitor doubler avoids the inductor and cannot reach 37 V from a single cell without several stages

Points to check before this part goes on a BOM

The 90 mV of headroom is the efficiency story. A boost converter that holds a fixed 20 V rail and feeds a string that needs 18.6 V burns 1.4 V in the current sink at 20 mA, which is 28 mW per string and 56 mW of pure loss. This part measures the sink voltage and adjusts the boost output so the sink sits at 90 mV, and the loss falls to 3.6 mW. On a phone backlight that runs at 40 mA total, that is the difference between 85 and 90 per cent efficiency, and it is also the difference between a warm patch at the bottom of the panel and none.

Two strings on one converter need matching, not just accuracy. The two sinks hold 1 per cent of each other, which at 20 mA is 200 uA, and the boost regulates on the lower of the two sink voltages so neither string is starved. A driver that regulates on the average leaves one string with insufficient headroom and the panel shows a vertical band. The matching figure is quoted separately from the accuracy figure for exactly this reason, and a datasheet that only quotes one of them is telling half the story.

The overvoltage clamp is a protection level and also a limit the string has to respect. This member clamps at 36 to 39 V, so a string of ten LEDs at 3.5 V each reaches 35 V and fits with 1 V to spare. A string of eleven LEDs needs 38.5 V and sits inside the clamp window, so an open string can trip the clamp before the string is fully driven. The 26.5 V member exists for the shorter strings, and choosing the higher clamp for a short string means an open circuit is protected at a voltage the switch does not need to reach.

The body marking is shared with the 26.5 V member, and that is a real line side hazard. Both parts print 61162A on the package, both come on the same 3000 piece reel, and the only difference is the reel label and the order code. A goods inwards process that decodes the marking instead of the label cannot tell a 37.5 V part from a 26.5 V part, and the mistake shows up as a backlight that clamps early and flickers. The check has to be on the label, and the reel has to stay with its label until the line takes it.

The one wire interface is what removes a trace from the flex. A PWM line needs a dedicated pin on the panel connector and a frequency that does not beat with the boost, and the one wire interface sends a nine bit code over the enable line instead. The cost is that the code has to be written at the right time, because the interface shares the enable pin and a glitch during a write changes the brightness. The data sheet gives the timing and the acknowledge behaviour, and a firmware that toggles the enable for a reset has to know it is also sending a command.

Thermal is not a small matter in a 1.45 mm body. The junction to ambient figure is 107 C per watt, and at 80 per cent efficiency with a 1.5 W backlight the part dissipates 375 mW, which is a 40 C rise. In a phone that is warm to the touch but inside the limit, and in a module with no airflow the same dissipation takes the junction to 125 C and the headroom control starts to lose accuracy. The boost diode and the inductor are outside the package and contribute their own heat to the same patch of board.

Setting the string current from one resistor

The ISET pin sits at 1.229 V at full brightness and the current through the resistor is multiplied by 1030 to give the string current. A 60 kOhm resistor passes about 20.5 uA and sets 21 mA per string, and a 41 kOhm resistor sets 30 mA, which is the ceiling of the sink. The multiplier has its own tolerance and the resistor has its own, so the current lands within a couple of per cent, which is what the accuracy specification describes.

Dimming works by scaling that reference rather than by chopping the current. The nine bit code scales the ISET voltage, so the sink stays in regulation at low brightness and the loop does not have to recover from a full off state. A PWM dimming line does chop the current, and at a 100 to 1 ratio the on time is short enough that the boost output sags between pulses unless the output capacitor is large enough to hold it.

Why the start up current limit is lower

At start up the output capacitor is discharged and the boost has to charge it to 35 V through the inductor. If the switch ran at its full 2 A limit the inrush would collapse the battery rail, so the part limits itself to about 0.7 A until the output is up and then switches to the full limit. The half limit window of 5 ms is the period during which a fault is allowed to hold the current at half the limit before the part shuts down.

A long string of LEDs also has a start up voltage above the battery, so the boost runs at a high duty cycle from the first cycle. A 4.7 uH inductor at 1.2 MHz carries the full string current with about 0.3 A of ripple at 3.6 V in, and the inductor has to hold its value at the 1.5 A switch limit rather than at the operating current.

Where this order code fits

This is the backlight driver in a smartphone, a handheld terminal, a GPS receiver or a small panel display, where two strings of up to five white LEDs run from one lithium cell and the panel dims over a 100 to 1 range Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

How many LEDs can it drive? Two strings of up to five, so ten LEDs in total, with each sink limited to 30 mA. The 37.5 V clamp on this member allows a string of ten in series at low current.

Does it need an external diode? No. The switch is on the die and the rectifier is external, which is the one component the data sheet shows outside the package alongside the inductor.

Why is the body marked 61162A? Because the two overvoltage options share a marking. The reel label and the order code are what separate a 37.5 V part from a 26.5 V part.

What sets the brightness? The ISET resistor sets the full brightness current and the one wire interface or the PWM pin scales it. Nine bits of resolution come from the one wire path.

Can the two strings be different lengths? They can, but the boost regulates on the lower sink voltage, so the longer string sets the rail and the shorter one burns the difference in its sink. Equal strings keep the loss at 90 mV per string.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.