TPS54336ADDAR
Product Specifications
TPS54336ADDAR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54336ADDAR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54336ADDAR fixed 340 kHz 3 A buck with an adjustable soft start pin
The TPS54336ADDAR is the fixed frequency member of the TPS5433xA family: 4.5 V to 28 V input, 3 A output, 128 milliohm high side and 84 milliohm low side switches inside an 8 pin SO PowerPAD body. Where its sibling sets the switching frequency with a resistor, this one runs at 340 kHz and puts the soft start ramp under the control of an external capacitor on the SS pin. That single change moves the part from a general purpose converter into a supply that has to come up in a defined time, either to limit inrush into a large output capacitance or to track another rail.
The SS pin is not a simple timer. The voltage on it overrides the internal reference, so the output follows whatever ramp is applied there. A capacitor to ground gives an exponential ramp set by the 2.3 microamp charge current; an external divider gives tracking and sequencing without extra parts. When the pin is left alone the internal reference takes over and the converter starts on its own schedule, which is why a board that behaves on the bench and misbehaves in a rack is often a board where that node was left floating through a via.
Everything else in the signal chain is shared with the adjustable member: the 0.8 V reference at 0.8 per cent initial accuracy, the pulse skipping at light load, the monotonic start into a pre-biased output, the cycle by cycle high side limit with a low side sourcing limit behind it, and hiccup mode after a persistent fault.
Key parameters from the SLVSCD5D document
| Input range | 4.5 V to 28 V operating, 30 V absolute maximum, with the UVLO rising between 4 V and 4.5 V and 180 mV to 400 mV of hysteresis |
| Output current | 3 A continuous across a 0.8 V to 24 V output window |
| Switching frequency | Fixed at 340 kHz internally, no external timing component needed |
| Soft start | External capacitor on SS charged at 2.3 microamp typical, with the pin voltage overriding the internal reference for tracking |
| Reference | 0.8 V, 0.7936 V to 0.8064 V at 25 degrees, 1.5 per cent over the full junction range |
| Quiescent current | 310 microamp typical and 800 microamp maximum non switching, 2 microamp typical in shutdown with EN low |
| Power switches | 128 milliohm high side and 84 milliohm low side at 12 V input |
| Orderable body | SO PowerPAD, 8 pins, 4.89 mm by 3.90 mm, 2500 pieces on a large reel for the R suffix |
Why 340 kHz is the right frequency for this body
A fixed 340 kHz sits in the band where a 3 A converter with 128 milliohm switches still runs above 90 per cent efficiency at 12 V to 5 V, while the inductor and the output capacitor stay small enough for a body this size. Pushing the same silicon to 1 MHz would shrink the inductor but the switching loss in the high side FET would take the efficiency down at full load, and the thermal pad on an SO package has less headroom than the VSON body does.
The trade is that 340 kHz puts the fundamental in a place an automotive or instrumentation EMC scan can see, and the loop crossover has to sit well below it. The compensation network on COMP is external, so an engineer who changes the output capacitor from a bulk electrolytic to ceramics has to move the compensation with it, otherwise the transient response rings even though the DC regulation is fine.
Protection and start up sequence
On enable the part holds the high side off until the internal reference reaches its regulation point, and the SS ramp then controls the rise of the output. If the output is already charged through a body diode, the monotonic start feature stops the converter from pulling it down before it ramps up, which avoids the negative dip that resets downstream logic. Cycle by cycle current limiting on the high side is enhanced by a low side sourcing limit and a low side sinking limit, and a fault that persists beyond the internal hiccup time shuts the switches off for 2 ms before retry.
Thermal shutdown is specified between 160 and 175 degrees with 10 degrees of hysteresis. Overvoltage transition protection holds the high side off when the output is driven above regulation, which is what happens when a second supply on the same rail wins the race at power up.
Where this part fits
Fixed frequency with an adjustable ramp suits a set top box or a digital TV main board where the 5 V rail has to come up after the 12 V rail and before the audio stage, an industrial panel where inrush into a large bulk capacitor trips the upstream fuse, and a carrier board where several rails are sequenced from one controller. The 8 pin SO PowerPAD body is also the easier of the two packages for hand rework during a pilot build, which matters when a customer is still changing the bill of materials between runs.
For a procurement team the family view is more useful than the single part number: both members share pads, and the difference is confined to pin 8 and the frequency. That is the kind of substitution that can be made in an afternoon rather than a re-spin, and the same logic is set out in pin to pin cross reference and in power management cross reference.
What to check before a purchase order
The first field is the family letter: TPS54336A is the fixed 340 kHz part, TPS54335A is the adjustable one, and the two share a document and often a distributor page. The second is the package code, since DDA is the SO PowerPAD and DRC is the 10 pin VSON with a different pad geometry. The third is the reel size, where the R suffix row carries 2500 pieces on a large reel.
Our desk confirms those three against the bill of materials and, when the fixed frequency part is short, offers the adjustable member with the RT resistor value that reproduces 340 kHz rather than an unrelated substitute. See component lead time solutions and BOM shortage recovery for how that is handled when a reel is not on the shelf.