INA141UA
Product Specifications
INA141UA
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA141UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA141UA: the UA grade in a tube, gain of 10 or 100
INA141UA is the UA grade in a 75 piece tube, which is the carrier a prototype or a low volume build actually wants. The U in the code is not the grade here: the suffix after the U is the grade, so UA is the wider offset bin, 250 microvolts at a gain of 10 and 125 at a gain of 100, and the plain U is the tighter one.
Reading that code backwards is the most common ordering error on this family, and it is worth stating plainly: INA141U is tighter than INA141UA, on this part and across the Burr-Brown line. What the UA grade buys is availability in small quantity and a lower price, and what it costs is 150 microvolts of offset and half the common mode rejection at a gain of 100.
INA141UA as the vendor document publishes it
| Gain | 10 V/V with pin 1 open, 100 V/V with pin 1 shorted |
| Gain error, G = 10 | 0.05 per cent maximum |
| Gain error, G = 100 | 0.075 per cent maximum |
| Gain drift | 2 ppm per degree typical, 10 maximum |
| Offset, G = 10 | 100 microvolts maximum |
| Offset, G = 100 | 50 microvolts maximum |
| Offset drift | 2 microvolts per degree maximum |
| Common mode rejection, G = 100 | 117 dB minimum, 125 typical |
| Input bias current | 2 nanoamps typical, 5 maximum |
| Input impedance | 100 Gohm in parallel with 2 pF, differential |
| Bandwidth, G = 10 | 994 kHz on SHE, 610 kHz on TID |
| Bandwidth, G = 100 | 200 kHz |
| Slew rate, G = 10 | 4 volts per microsecond on SHE, 2 on TID |
| Settling to 0.01 per cent | 7 microseconds at G = 10, 9 at G = 100 |
| Overload recovery | 4 microseconds from a 50 per cent overdrive |
| Output swing | within 1.4 volts of each rail on SHE, 0.15 on TID |
| Quiescent current | 750 microamps typical, 800 maximum on SHE; 590 typical on TID |
| Supply range | plus or minus 2.25 to plus or minus 18 volts, 4.5 to 36 volts single |
| Stable load capacitance | 1000 picofarads |
| Short circuit current | 20 milliamps |
| Body | eight pin SOIC, D package |
| Temperature range | minus 40 to plus 85 degrees |
| Catalogue code | INA141UA |
| Carrier | 75 piece tube |
| Grade | UA, 250 microvolts at a gain of 10 |
100 microvolts at a gain of 10, 50 at a gain of 100
Offset on INA141UA is quoted per gain and per grade, and the pairs are the whole selection story. At a gain of 10 the U grade is 100 microvolts maximum and the UA grade 250; at a gain of 100 the same two grades read 50 and 125 microvolts. Drift runs 2 microvolts per degree maximum on the U grade and 2.5 on the UA, and the drift window is specified over minus 40 to plus 85 degrees.
The counterintuitive part is that the offset improves as the gain rises, because the input stage dominates the error and its contribution is referred back through the first stage. A 250 microvolt UA part at a gain of 10 is 2.5 millivolts at the output, which on a 4 V span is 0.06 per cent and can be trimmed once. Its 2.5 microvolts per degree is 100 microvolts over a 40 degree swing at the input, 1 millivolt at the output, which cannot be trimmed once and has to be budgeted.
A gain of 10 or 100 from a strap on pin 1
INA141UA has no gain resistor and no gain equation. The three op amp network and its resistors are trimmed on the die to a gain of 10 V/V, and a single pin decides whether the second stage is in or out: with the pin left open the gain is 10, with the pin shorted to the common point the gain is 100. Nothing else about the circuit changes, which is why the same board can serve a bridge channel at 10 and a thermocouple channel at 100 without a resistor change.
Two numbers decide whether that strap is a convenience or a trap. The vendor states that 0.5 ohm of series resistance in the strap reduces the gain by 0.1 per cent, so a mechanical jumper with a tired contact is already a gain error, and the strap should be a solder link or a zero ohm part rather than a header. The vendor also states that the internal resistors carry about 25 per cent of value spread, so gains between 10 and 100 set with an external resistor are uncertain and are not the intended use of INA141UA.
The reference pin has to see 8 ohms or better
The output of INA141UA is referred to the Ref pin, and the vendor is unusually specific about what that pin tolerates: 8 ohms in series with Ref drops common mode rejection to about 80 dB at a gain of 10. That is the pin a divider, a buffer or a ground return lands on, and a 1 kohm divider feeding it directly is three orders of magnitude outside the window. The reference has to come from an amplifier or from a solid ground, never from a resistor network.
The same rule applies to the strap in the previous section and to the input returns. On a single supply the reference sits at mid rail and the rejection figure now depends on that node holding still while the common mode moves, so the buffer that sets mid rail is part of the amplifier, not part of the power supply. On a dual supply the pin is grounded at the star point, and a separate analog ground that carries the reference current back is worth more than any capacitor on the pin.
SHE and TID: one part number, two different chips
The electrical table for INA141UA is split by chip site origin, SHE and TID, and the two columns are not interchangeable. At a gain of 10 the SHE reading is 100 microvolts maximum offset against 80 microvolts on TID, and the bandwidth is 994 kHz against 610 kHz. At a gain of 100 the SHE part settles in 9 microseconds against 7, and the quiescent current is 750 microamps against 590.
What the split really changes is the output stage. The SHE chip swings to within 1.4 V of each rail, the TID chip to within 0.15 V, so a channel that has to reach 4.5 V on a 5 V rail works on one origin and clips on the other. Because the body marking is the only visible difference, INA141UA on a purchase order pins the body but not the origin. A build that needs the wider output swing should say so on the order or screen the incoming lot; a build that only needs the offset does not care.
800 microamps, plus or minus 2.25 to 18 volts and the D body
INA141UA draws 800 microamps maximum, 750 typical on the SHE chip and 590 on TID, from a supply anywhere between plus or minus 2.25 and plus or minus 18 volts, or 4.5 to 36 volts single. That window is wide enough to run from an unregulated 24 V rail with margin and narrow enough at the bottom to run from a 5 V rail with the reference at mid supply. The part is stable into 1000 picofarads and limits short circuit current at 20 milliamps.
The body is the eight pin SOIC, the D package, which on INA141UA is the only body offered in this catalogue entry. Thermal resistance is 150 degrees per watt in still air, so 800 microamps at 30 volts total, 24 milliwatts, raises the junction 4 degrees, and the package is not the limit at any supply in the window. What the small body does limit is the copper available to the reference pin, which is why that pin wants a short trace to the buffer rather than a long one to the ground plane.
7 microseconds to settle and 4 to recover
Settling on INA141UA is 7 microseconds to 0.01 per cent at a gain of 10 and 9 microseconds at a gain of 100, measured on a 5 V step. Overload recovery from a 50 per cent overdrive is 4 microseconds. The bandwidth is 994 kHz on the SHE chip and 610 on TID at a gain of 10, falling to 200 kHz at a gain of 100 on both.
For a multiplexed front end the sum of those numbers is the scan budget. Sixteen channels at 9 microseconds of settling plus the acquisition window of the converter is a few hundred microseconds per scan, which suits pressure, temperature and strain logging and does not suit a vibration channel above a few kilohertz. The recovery figure matters more than the settling figure in that calculation, because a multiplexer that switches from an open channel to a live one presents exactly the overdrive the recovery row describes.
Seventy five pieces is two or three prototype builds and a first article, which is the right quantity for a channel that has not been calibrated yet. If the build settles on the UA grade, the next purchase should be the reel, because the tube is the carrier that disappears first in a shortage. Our safety stock planning page covers the arithmetic of holding a reel against buying cut stock, and the pin to pin cross reference page covers what to check before a second source is qualified.
Is the UA grade good enough for a bridge channel at a gain of 100? At 125 microvolts of offset, referred to the input, a 2 millivolt per volt bridge output sees 0.06 per cent of error, which is inside a 12 bit budget and outside a 16 bit one without a trim. The drift, 2.5 microvolts per degree, is the term that a trim cannot remove.
The second question is whether the tube can be reflowed. It cannot: the tube is a through hole part in this body, and a board built for the reel needs the reel. Confirm the carrier on the order before the assembly is released.