Contact Us

INA149AMDREP

Brand: Texas Instruments
Texas Instruments INA149AMDREP is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA149AMDREP — Power Management & Signal Chain | Superb Automation

INA149AMDREP

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA149AMDREP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA149AMDREP: the enhanced product suffix on the 275 volt amplifier

INA149AMDREP carries an REP suffix, which in this vendor's convention marks an enhanced product released against a defined flow rather than a new silicon. The device is the INA149: plus or minus 275 volts of common mode, unity gain, 90 dB of rejection over minus 40 to plus 125 degrees, 500 kHz and 900 microamps.

The page states the suffix as the catalogue carries it and does not claim a qualification the vendor document does not print. What the document does support is the electrical behaviour and the temperature range, and on a 275 volt front end those are the rows that decide whether the part can be used at all. The suffix question is a paperwork question and belongs on the purchase order.

INA149AMDREP as the vendor document publishes it

Gain1 V/V fixed
Gain error0.005 per cent typical, 0.02 maximum
Gain drift1.5 ppm per degree typical, 10 maximum
Nonlinearity0.0005 per cent typical, 0.001 maximum of full scale range
Offset350 microvolts typical, 1100 maximum
Offset drift3 microvolts per degree typical, 15 maximum
Supply rejection90 dB minimum, 120 typical
Common mode rangeplus or minus 275 volts
Overload withstand500 volts momentary, common mode or differential
Common mode rejection at dc90 dB minimum, 100 typical
Common mode rejection at 1 kHz90 dB minimum with 500 volts peak to peak
Input impedance800 kohm differential, 200 kohm common mode
Voltage noise20 microvolts peak to peak, 550 nanovolts per root hertz at 10 kHz
Bandwidth500 kHz small signal, 32 kHz full power at 20 volts peak to peak
Slew rate1.7 volts per microsecond minimum, 5 typical
Settling to 0.01 per cent7 microseconds on a 10 V step
Output swingplus or minus 13.5 volts on plus or minus 15 volt supplies
Quiescent current810 microamps typical, 900 maximum, 1.1 milliamps over temperature
Supply rangeplus or minus 2 to plus or minus 18 volts
Stable load capacitance10 nanofarads
Bodyeight pin SOIC, pin compatible with the INA117 and INA148
Temperature rangeminus 40 to plus 125 degrees
Catalogue codeINA149AMDREP
Suffix noteREP is an enhanced product flow, not an automotive Q1
GradeA grade in the D body

1100 microvolts of offset and 0.02 per cent of gain error

Offset on INA149AMDREP is 350 microvolts typical and 1100 maximum, with 3 microvolts per degree typical and 15 maximum of drift over minus 40 to plus 125 degrees. Gain error is 0.005 per cent typical and 0.02 maximum, gain drift 1.5 ppm per degree typical and 10 maximum, and nonlinearity 0.0005 per cent typical and 0.001 maximum of full scale range. Supply rejection is 90 dB minimum.

On a 275 volt common mode the offset is the small term and the rejection is the large one, which is the opposite of a low voltage instrumentation amplifier where the offset usually dominates. Eleven hundred microvolts on a plus or minus 10 volt range is 0.0055 per cent of full scale, a twentieth of what a 16 bit converter can resolve, so the offset does not need trimming and the drift over 125 degrees, 15 microvolts per degree or 2.5 millivolts, still does not. What does need attention is the 0.02 per cent gain error, which is 4 millivolts on a 20 V span and is a ratio error that no single point trim removes.

900 microamps from plus or minus 2 to plus or minus 18 volts

INA149AMDREP draws 810 microamps typical and 900 maximum at plus or minus 18 volts, rising to 1.1 milliamps over temperature, from a supply between plus or minus 2 and plus or minus 18 volts. The output swings to plus or minus 13.5 volts on a plus or minus 15 volt supply, limits short circuit current at 25 milliamps and drives 10 nanofarads without sustained oscillation.

The 2 volt floor is unusual for a part with a 275 volt input window and it matters on a 3.3 V rail, where the part still works with the window scaled to twice the supply. The output window of plus or minus 13.5 volts on plus or minus 15 volts is also wider than most instrumentation amplifiers manage, which is what allows the part to drive a plus or minus 10 volt converter directly without a second stage and without giving up the headroom that the converter needs.

Pin compatible with the INA117 and the INA148

The vendor states that INA149AMDREP is pin compatible with the INA117 and the INA148 family, in the eight pin SOIC, and that it improves on both. On a board that already carries one of those parts, INA149AMDREP is therefore a candidate for a straight swap, and the figures that make it attractive are the 500 kHz bandwidth against 100 to 155 kHz on the INA148, the 90 dB minimum rejection held over temperature, and the 0.02 per cent gain error.

Three rows have to be checked before a swap is signed off. The supply window differs: plus or minus 2 to plus or minus 18 volts here against plus or minus 1.35 to plus or minus 18 on the INA148. The reference arrangement differs on the two reference pins, and a board that ties one of them to a divider will not behave the same way. And the output swing, plus or minus 13.5 volts here, is wider than the part it replaces, so a circuit that relied on clipping at a lower level will now deliver a larger signal to whatever follows.

90 dB minimum rejection from minus 40 to plus 125 degrees

Common mode rejection on INA149AMDREP is 90 dB minimum and 100 typical at dc with the common mode at plus or minus 275 volts, and 90 dB minimum at 500 Hz and at 1 kHz with a 500 volt peak to peak common mode. The temperature row is the unusual one: the minimum holds from minus 40 to plus 125 degrees, not just at 25, so the rejection does not have to be derated across the operating range.

Ninety dB is a factor of thirty thousand, so 275 volts of common mode becomes 8.7 millivolts referred to the input, and 500 volts of transient becomes 16 millivolts. That is the number that decides whether the part can be used ahead of a 12 bit converter on a plus or minus 10 volt range: 8.7 millivolts is 0.09 per cent of full scale, below the converter's own linearity, and at 16 bits it is not and the common mode has to be reduced or the measurement taken differentially.

500 kHz, 5 volts per microsecond, 7 microseconds to settle

The small signal bandwidth of INA149AMDREP is 500 kHz, the slew rate is 1.7 volts per microsecond minimum and 5 typical, the full power bandwidth is 32 kHz at 20 volts peak to peak, and the settling time to 0.01 per cent on a 10 V step is 7 microseconds. Output noise is 20 microvolts peak to peak from 0.01 to 10 Hz and 550 nanovolts per root hertz at 10 kHz.

The ratio between 500 kHz of small signal bandwidth and 32 kHz of full power bandwidth is the practical limit: a 20 volt swing at 1.7 volts per microsecond cannot complete faster than about 12 microseconds, so anything above 32 kHz comes out as a triangle. For a line frequency measurement that is irrelevant; for a switching waveform it is the reason to use a different part. The 7 microsecond settling figure is the one a multiplexed channel budgets, and it is fast enough for 16 channels at 9 kilohertz per channel.

Plus or minus 275 volts of common mode and 500 volts of overload

INA149AMDREP is a unity gain difference amplifier whose input common mode range is plus or minus 275 volts, and whose inputs survive a momentary common mode or differential overload of 500 volts. That combination is what allows the part to sit directly on a three phase line or a battery stack without a divider, and it is why the vendor positions it as a replacement for an isolation amplifier where galvanic isolation is not required.

The economic argument is in the paragraph that follows the first one in the vendor document: an isolation amplifier needs an isolated supply on the input side, and that supply brings ripple, noise, quiescent current and a transformer. Removing it removes the isolated dc to dc converter, its creepage distance and its cost, and leaves a part that measures small differentials on a large common mode with 90 dB of rejection. What is given up is the isolation itself, which matters for safety and not for measurement.

Where a programme needs a defined flow, ask for the flow document with the quote rather than after the goods arrive. Our incoming inspection plan covers the paperwork check, and the obsolete part cross reference hub covers the route if the enhanced row is withdrawn.

Is REP the same as an automotive Q1? No. They are different flows with different documents, and this family does not publish a Q1 row in the document read for this page.

Does the suffix change the input window? No. The window is plus or minus 275 volts on every row of the family, and the momentary overload rating of 500 volts is unchanged.