Contact Us

TPS1HTC100QPWPRQ1

Brand: Texas Instruments
Texas Instruments TPS1HTC100QPWPRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS1HTC100QPWPRQ1 — Power Management & Signal Chain | Superb Automation

TPS1HTC100QPWPRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS1HTC100QPWPRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS1HTC100QPWPRQ1 83 milliohm 4 A automotive high side switch in the 14 pin HTSSOP body

The TPS1HTC100QPWPRQ1 is a single channel smart high side switch for 24 V automotive systems, with an integrated N channel FET and charge pump in a 14 pin HTSSOP package. It works from 6 to 60 V, carries 4 A of direct current, and specifies 83 milliohms typical on resistance with accurate current sensing at plus or minus five per cent at 1 A. The part is AEC-Q100 qualified at temperature grade 1, which is minus 40 to plus 125 C ambient.

The reason a 60 V part exists in a 24 V system is load dump and jump start. A 24 V battery system in a truck or a bus sees transients well above its nominal rail, and a switch rated only to 36 V survives on the bench and fails in the field. The 60 V rating also allows the same part to be used on a 48 V rail in industrial equipment, which is why the part appears outside automotive as well. The diagnostics are the second reason: open load and short to battery detection in both the on and off states, plus a sense output that can feed an ADC.

Key parameters taken from the TPS1HTC100QPWPRQ1 document

Input range6 to 60 V operating, with reverse battery protection using external components
On resistance83 milliohms typical and 180 milliohms maximum over the junction range
Load current4 A direct current, with an adjustable current limit from 1 A to 5 A or 7.3 A
Current sensePlus or minus 5 per cent accuracy at 1 A, with a sense output scaled for an ADC input
Standby currentBelow 0.5 microamps, with a quiescent current below 2 mA
Undervoltage lockoutRising threshold 5.0 to 5.75 V, falling threshold 4.1 to 4.85 V
ProtectionOverload and short circuit protection, integrated inductive discharge clamp, loss of ground and loss of supply protection, absolute and relative thermal shutdown
DiagnosticsOn and off state open load and short to battery detection, overload and short to ground detection, fault reported on a dedicated pin
Logic interface1.8 V, 3.3 V and 5 V compatible inputs
Functional safetyFunctional safety capable, with documentation available to support a safety case
ThermalThermally enhanced HTSSOP body with an exposed pad, 5 by 6.4 mm, 0.65 mm pitch
TemperatureMinus 40 to plus 125 C ambient, AEC-Q100 grade 1
BodyHTSSOP 14 pins, 5 by 6.4 mm
Order code factsTPS1HTC100QPWPRQ1, HTSSOP PWP 14 pins, 3000 pieces on a large reel, NIPDAU finish, moisture level 3 with a 168 hour floor life, marking TPSHT00

The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.

Where the numbers matter in a real build

The 83 milliohm typical figure becomes 180 milliohms maximum, and that maximum is what the thermal calculation has to use. At 4 A the dissipation is 1.3 W typical and 2.9 W worst case, which on an HTSSOP with an exposed pad needs a copper area and, on a sealed module, a thermal path to the housing. Customers who run the part at 4 A continuously in a hot environment usually find that the current has to be derated, and the derating curve in the document is the place to find the number rather than a rule of thumb.

The current limit range is wide and it is set by a resistor, which means the same part can protect a 1 A actuator or a 5 A lamp. The limit has three published thresholds, and the lowest one is for loads that need a tight bound. On an inductive load, the limit has to be above the inrush but below the damage threshold of the wiring, and the inductive discharge clamp is what absorbs the energy when the switch opens. Without that clamp the switch would see a voltage spike limited only by the load inductance and the wiring.

The current sense output is what turns the part into a diagnostic device rather than a relay. At plus or minus five per cent at 1 A, a controller can measure the load current, detect a failing actuator before it fails, and distinguish an open load from a short. That accuracy is specified at 1 A and degrades at low currents, so a product that wants to detect a 100 mA open load condition should check the sense behaviour at that current rather than assume the headline figure applies.

The undervoltage lockout window sits between 5.0 and 5.75 V rising, which matters in a 24 V system during a cold crank. The rail can fall well below the nominal during starting, and the switch will drop out and come back, which is normally acceptable for a lamp but not for a controller that has to hold its state. The part reports the condition through the fault pin if the diagnostics are enabled, so the controller can tell a crank from a genuine fault.

  • Dissipation at the maximum on resistance and the maximum load current, with the copper area the board actually has.
  • Current limit setting against the measured inrush of the real load, including the temperature coefficient of the limit.
  • Sense output accuracy at the current the diagnostics depend on, not only at 1 A.
  • Behaviour during a supply dip below the lockout threshold, since the switch will drop out and recover.
  • Thermal shutdown behaviour on a stalled load, to confirm the part cycles rather than latching.
  • Reverse battery condition with the external components fitted, because the protection is external to the part.

Which projects this part fits

This part fits 24 V automotive body control, lamp and actuator drive, seat and window modules, HVAC blowers, and any load that has to be switched with diagnostics at a battery level rail. It also fits 48 V industrial equipment, telecom rectifier outputs and battery backed systems where a 60 V switch with current sense is useful. Customers building a module that has to report load health use the sense output with an ADC, and customers who need two channels use the dual member of the family, which shares the diagnostics but has a different thermal profile.

Questions that come up before a purchase order is released

Why a 60 V part in a 24 V system?

Because the rail is not 24 V all the time. Load dump, jump start and inductive transients push it far above nominal, and a switch rated at 36 V will survive the bench and fail in a truck. The 60 V rating also gives margin for the clamp energy when an inductive load is switched off, which is a repetitive stress rather than a one off event.

How is the current limit set?

With a resistor to ground on the limit pin, choosing one of three published thresholds. The limit is a window rather than a single value, and the window has to sit above the load inrush and below the wiring rating. On a load with a large inrush the blanking or a higher threshold is needed, and the choice is made against the measured inrush rather than from the load specification.

What does the sense output connect to?

An ADC input through a resistor, normally with a filter capacitor for the switching noise. The scaling is set in the document and is referenced to the supply, so the reading is a ratio rather than an absolute voltage. A controller that uses the sense for protection should also have the fault pin, because the sense alone cannot tell a short from a heavy load at the top of the range.

Can the part drive a lamp?

Yes, and lamps are one of the harder loads because the cold filament draws ten times its steady current. The current limit has to be set high enough for that inrush, the thermal path has to survive the repetitive peak, and the diagnostics may report an overload during the first tens of milliseconds. A product that switches lamps should have the limit and the thermal path checked on the real lamp rather than on a resistive load.

How is the part checked at incoming inspection?

Reel and moisture bag check, marking check, and a functional test on a board that switches a load, exercises the current limit and reads the fault pin. On resistance can be measured on a sample with a four wire setup at a known current, which catches a mixed lot. Because the part is automotive qualified, the lot and date code record is kept with the test result for traceability.

How SUPERB handles this line

We supply the TPS1HTC100QPWPRQ1 from original reels with lot and date code traceability, and we check the marking on a sample because the HTSSOP body is easy to confuse with the non automotive members of the family. The power management cross reference page lists the high side switch and protection families we carry, CAN bus transceiver selection covers the interface parts that sit on the same 24 V module, and incoming inspection plan is the page to read when a part has to be screened before it reaches a line.