Contact Us

INA180B2QDBVRQ1

Brand: Texas Instruments
Texas Instruments INA180B2QDBVRQ1 is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA180B2QDBVRQ1 — Power Management & Signal Chain | Superb Automation

INA180B2QDBVRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA180B2QDBVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA180B2QDBVRQ1: 50 V/V current sense amplifier in the five pin SOT-23 on the alternate B pinout

INA180B2QDBVRQ1 is a fixed gain current shunt monitor from the INAx180 family, the member that carries the 50 V/V gain on pinout B in a SOT-23 body of 5 pins. It measures the drop across a shunt at common mode voltages from minus 0.2 V to plus 26 V independently of its own supply, runs from a single 2.7 V to 5.5 V rail, draws 260 uA maximum on the single channel, and holds a plus or minus 150 uV offset limit at zero common mode with a plus or minus 1 per cent gain error over the full temperature range. The B in the string is a pinout variant rather than an electrical grade, and that one letter is what decides whether the part drops into a board built for the A arrangement.

Order code and package

INA180B2IDBVRSOT-23 DBV body, 5 pins, 3000 pieces on a large reel, Active in the addendum dated 23 October 2026, NIPDAU finish, moisture level 1 with no floor life limit, marking 1ABD, minus 40 to plus 125 degrees
INA180B2QDBVRQ1the string printed in this catalogue entry carries a Q1 suffix, which is the automotive grade. The automotive grade is published as its own document, INA180-Q1 with the INA2180-Q1 and INA4180-Q1 siblings, and the packaging addendum inside this industrial file lists the industrial rows only, so the Q1 reel size and moisture rows have to be read from the automotive addendum
INA180B2IDBVTthe same DBV body on a 250 piece small reel, which is the column a prototype build or a repair order comes from
INA180B2IDBVR.Bthe .B revision row of this exact string is printed Obsolete in the same addendum that prints the plain row Active, so a quote issued against the .B suffix is quoting a status the vendor has already closed
INA180A2IDBVRthe same 50 V/V gain on pinout A, 3000 pieces on a large reel, marking 1A8D, which is the row to compare when the board footprint was drawn for the A arrangement and the reel has to match it

Electrical parameters that decide the application

Common mode rangeminus 0.2 V to plus 26 V, independent of the supply, so a 24 V rail sits inside the window with 2 V of headroom
Supply2.7 V to 5.5 V single rail, 260 uA maximum quiescent on the single channel, 500 uA on the dual and 900 uA on the quad
Offset voltageplus or minus 150 uV maximum at zero common mode and plus or minus 500 uV maximum at 12 V, both referred to the input
Offset drift1 uV per degree maximum, quoted in the features list across the minus 40 to plus 125 degree range
Gain50 V/V fixed on the B2 member, against 20 V/V on A1 and B1, 100 V/V on A3 and B3 and 200 V/V on A4 and B4
Gain errorplus or minus 1 per cent maximum over temperature, quoted against a 10 mV sense signal so the window widens at smaller drops
Common mode rejection84 dB minimum and 100 dB typical, measured with a 10 mV sense signal and a common mode swept from 0 V to 26 V
Bandwidth350 kHz on the 20 V/V member with a 10 mV sense signal, and the figure falls as the fixed gain rises
Slew rate2 V per microsecond on the output, which sets the response time of an overcurrent comparator built on this output
Input bias current50 uA typical at zero sense, drawn by the internal resistor network rather than by a transistor input
Outputvoltage output that drives an ADC input directly, ratioed to the sense voltage by the fixed gain with no external divider
Temperatureminus 40 to plus 125 degrees, the same range on the A and B devices and on all four gain grades

Family variants and how they differ

B2 against A2the two are the same silicon and the same 50 V/V gain on two different pin arrangements. The device comparison table states that A devices use pinout A and B devices use pinout B, so the choice is made by the existing footprint and never by the electrical table
INA2180 and INA4180the dual and quad members of the same family, eight pin VSSOP and WSON and fourteen pin TSSOP, with the same four gain options, which is how a three phase inverter gets three channels on one package
INA186 as the tighter alternative1.7 V to 5.5 V supply, zero drift, 50 uV offset and 25 to 500 V/V gains, but bandwidth drops to the tens of kilohertz at the high gain members against 350 kHz here
INA296A as the high voltage alternativeminus 5 V to 110 V common mode and 1.1 MHz at every gain, at 2.5 mA of supply current and a much higher price, which is the part for a 48 V bus
INA19x as the coarse alternativeminus 16 V to 80 V common mode, 20, 50 and 100 V/V, but a plus or minus 2 mV offset, which is thirteen times the offset of this device and rules it out below a 100 mV sense signal

Points to check before this part goes on a BOM

The offset limit moves with the common mode and that is the number to read first. At zero common mode the limit is 150 uV, at 12 V it is 500 uV, so a 24 V rail measurement carries 3.3 times the offset error of a ground referenced one. On a 10 milliohm shunt the 500 uV figure is 50 mA of apparent current before any gain error is counted, so a part chosen for a 5 A rail is fine and the same part on a 200 mA rail is not.

Gain error and offset trade places as the dominant term with signal size. At full scale the plus or minus 1 per cent gain error is the whole error budget, and at a tenth of full scale the fixed offset is larger than one per cent of the reading. A circuit that needs one per cent of reading across a ten to one range therefore needs a zero drift part, not this one, and the INA186 with its 50 uV offset and 10 ppm per degree gain drift is the member that covers that range.

The 50 uA of input bias current is a resistor network current and it flows in the shunt. On a 10 milliohm shunt that is half a microvolt and it disappears under the offset. On a 1 ohm shunt used to measure a small current it is 50 uV, which is a third of the offset limit on its own, so a high resistance shunt is the case where this current has to be added to the error budget rather than ignored.

The 84 dB common mode rejection is a DC figure. Above a few kilohertz the rejection falls, and the ripple of a switching supply sits on the bus as common mode at the switching frequency. Two 100 ohm resistors and a 100 nF capacitor at the two inputs are the usual addition, and the datasheet note on board arrangement asks for the capacitor to sit close to the device with the two input traces matched, because an unmatched pair converts common mode ripple into a differential signal that no amount of CMRR removes.

The 350 kHz bandwidth belongs to the 20 V/V member. At 50 V/V the same stage has less, and the output slew rate of 2 V per microsecond limits a 3.3 V output swing to about 1.6 us regardless of the small signal bandwidth. An overcurrent comparator that has to act inside 10 us is comfortable, and one that has to act inside 1 us is not, at which point the INA296A with its 8 V per microsecond slew and 1.1 MHz at every gain is the part to look at.

The Q1 suffix in this catalogue string is not covered by the document this page was written from. The vendor publishes the automotive grade as a separate file and lists only the industrial rows in this addendum, so the reel size, moisture level and part marking for INA180B2QDBVRQ1 have to be confirmed from that file or from the reel label. An offer that substitutes the industrial row for a Q1 order without saying so is the kind of substitution that fails an incoming inspection months later.

What the 26 V common mode window covers

Twelve, twenty four and twenty six volt rails sit inside the window with margin, and the minus 0.2 V at the bottom is there for the small negative excursion of a low side shunt during a switching event. A 48 V telecom or server rail does not fit, and neither does the 60 V spike on a 48 V bus, so a board with a 48 V input needs the INA296A with its 110 V operational and 120 V survival rating. Choosing this part for a 48 V rail because the gain and the package suit is the mistake that shows up as a dead input stage after the first hot plug event.

The supply is independent of the common mode, which is the point of the architecture: a 3.3 V logic rail can measure a 24 V bus without a divider. What the part does not do is survive a reversed bus, and the absolute maximum on the inputs is the supply plus 0.3 V, so a transient that drives the input above 26 V needs an external clamp rather than reliance on the amplifier.

Reading the order code

The string decomposes as INA180 for the single channel, B for pinout B, 2 for the 50 V/V gain, I for the industrial temperature grade, DBV for the five pin SOT-23, R for a large reel and Q1 for the automotive qualification. Each letter is a decision, and two of them, the B and the 2, are the ones a replacement order most often gets wrong: pinout A and pinout B are not interchangeable on a populated board, and gain 20 against gain 50 changes every reading by a factor of two and a half.

Where this order code fits

Motor control, battery monitoring, power management, lighting control, overcurrent detection and solar inverters are the applications the vendor names, and each of them presents the amplifier with a bus that moves while the sense signal stays small. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can INA180B2QDBVRQ1 replace INA180A2IDBVR on a populated board? No. The A devices use pinout A and the B devices use pinout B, so the inputs and the supply land on different pins and the part will not work in the other footprint.

Does it measure a 48 V rail? No. The common mode window stops at 26 V and the survival rating is only a fraction above that, so a 48 V bus needs a part rated for 110 V.

Is the Q1 automotive grade described by this document? No. This is the industrial document, and the automotive grade is published separately, so the Q1 reel and moisture rows must be confirmed from the automotive addendum.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.