Contact Us

INA821IDGKR

Brand: Texas Instruments
Texas Instruments INA821IDGKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA821IDGKR — Power Management & Signal Chain | Superb Automation

INA821IDGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA821IDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA821IDGKR: 35 uV offset, 7 nV per root hertz instrumentation amplifier in the eight pin VSSOP

INA821IDGKR is a precision instrumentation amplifier that sets any gain from 1 to 10000 with one external resistor in a VSSOP body of 8 pins. It runs from a single 4.5 V to 36 V rail or a split plus or minus 2.25 V to plus or minus 18 V supply, draws 600 uA typical and 650 uA maximum, and holds a 35 uV input offset limit with 0.4 uV per degree of drift. The gain term is 49.4 kOhm, so gain is 1 plus 49.4 kOhm divided by RG across the whole 1 to 10000 range.

Order code and package

INA821IDGKRVSSOP DGK body, 8 pins, 2500 pieces on a large reel, Active in the addendum dated 18 August 2026, NIPDAU finish, moisture level 2 with a one year floor life, part marking 1X4Q, minus 40 to plus 125 degrees
INA821IDGKTthe same DGK body on a 250 piece small reel at the same moisture level and the same 1X4Q marking, which is the route for a prototype build
INA821IDRSOIC D body, 8 pins, 2500 pieces on a large reel, same moisture level, marking INA821
INA821IDRGRSON DRG body, 8 pins, 3000 pieces on a large reel at moisture level 1 unlimited floor life, marking INA821, and this is the only body in the family with the unlimited floor life
INA821IDSOIC D body in a 75 piece tube, which is the column a repair order usually comes from

Electrical parameters that decide the application

Input stage offset10 uV typical, 35 uV maximum in the D and DRG bodies, 40 uV maximum in the DGK body, over minus 40 to plus 125 degrees
Offset drift0.1 uV per degree typical, 0.4 uV per degree maximum, uncorrelated between the two stages
Output stage offset50 uV typical and 400 uV maximum, referred to the input only after division by the gain
Gain equation1 plus 49.4 kOhm divided by RG, gain range 1 to 10000, gain error 0.005 per cent typical and 0.025 per cent maximum at unity gain
Gain drift5 ppm per degree at unity gain, 35 ppm per degree above unity gain, both excluding the external resistor
Common mode rejection92 dB minimum and 105 dB typical at G equal to 1, rising to 140 dB minimum and 150 dB typical at G equal to 1000
Power supply rejection110 dB minimum at G equal to 1, measured from the 4.5 V to 36 V range
Input bias current0.15 nA typical and 0.5 nA maximum at 25 degrees, 2 nA maximum across the full temperature range
Voltage noise7 nV per root hertz at 1 kHz, 0.14 uV peak to peak from 0.1 Hz to 10 Hz
Bandwidth4.7 MHz at G equal to 1, 970 kHz at G equal to 10, 290 kHz at G equal to 100 and 30 kHz at G equal to 1000
Slew rate and settling2.0 V per microsecond, 6 us to 0.01 per cent at gains up to 100 and 40 us at G equal to 1000
Input and output rangeinputs from 2 V above the negative rail to 2 V below the positive rail, output to within 0.15 V of either rail, stable into 1000 pF
Supply and current4.5 V to 36 V single or plus or minus 2.25 V to plus or minus 18 V split, 600 uA typical and 650 uA maximum, 870 uA maximum over temperature
Protectioninputs survive plus or minus 40 V, output short circuit current is plus or minus 20 mA continuous, RFI filter corner at 45 MHz

Family variants and how they differ

INA821 against INA828the INA828 is the related part with a 0.6 nA bias current maximum and 7 nV per root hertz of noise at the same 700 uA of supply current, so the two differ mainly in bias current and offset grade rather than in bandwidth
Offset limit by body35 uV in D and DRG, 40 uV in DGK, which matters because a 5 uV difference is 14 per cent of the limit and the body is chosen by reel size on most orders
Reference pin10 kOhm input impedance, accepts any voltage from the negative rail to 1 V below the positive rail, gain to the output of 0.01 per cent, which is what allows a bipolar signal to sit on a 2.5 V reference from a single 5 V rail
Supply floor4.5 V single supply is the minimum for the published offset and rejection figures, and the input window of 2 V from each rail leaves 0.5 V to 3.5 V of usable common mode on a 5 V rail
Package coolingthe DRG body is the smallest and the addendum prints moisture level 1 for it, so a board that reflows twice without a dry pack cycle is the case that body exists for

Points to check before this part goes on a BOM

The offset figure in the headline belongs to the input stage. Total offset referred to the input is the input stage offset plus the output stage offset divided by the gain, so at unity gain the 400 uV output stage limit adds to the 35 uV input limit for a 435 uV worst case, and the precision people buy this part for only appears from a gain of 10 upwards. A unity gain buffer built from this device is a 435 uV part, not a 35 uV part.

The 0.15 nA typical bias current is the number that decides the source impedance. At the 0.5 nA maximum and a 10 kOhm source, the bias current contributes 5 uV of offset, which is still below the 10 uV typical input offset. At 100 kOhm the same current contributes 50 uV and the amplifier's own offset stops being the limiting error, so a bridge with a high impedance arm is a source impedance question before it is an amplifier question.

The input window is 2 V from each rail regardless of gain. On a single 5 V supply that means the common mode has to sit between 2 V and 3 V, which is why a 0.5 V shunt or a ground referenced bridge is not workable on 5 V single supply even though the part is specified from 4.5 V. Either the supply goes up or the input sits on a reference, and the 10 kOhm reference pin is there for the second route.

Bandwidth does not follow a constant gain bandwidth product. The 4.7 MHz at unity gain and 290 kHz at a gain of 100 are a 29 MHz product at the high gain end, which is the current feedback input stage at work, so a gain of 100 still leaves 290 kHz of small signal bandwidth and a 10 V step still settles in 6 us. A stage that needs 1 MHz at a gain of 100 needs a different part, not a different resistor.

The output stage noise is 65 nV per root hertz, which is larger than the 7 nV input stage figure. At unity gain the two add to about 65 nV per root hertz at the output and the input stage noise is invisible; the 7 nV figure only becomes the dominant term once the gain is high enough to divide the output stage noise down, which is the same reason the offset behaves the way it does.

The DGK body carries moisture level 2 with a one year floor life while the DRG body carries level 1 with no floor life limit. Both are the same silicon, so the choice between them is a reflow and storage question rather than an electrical one, and a line that opens a reel, reflows half of it and stores the rest for a year should be on the DRG body.

Gain resistor values and the error they add

With a 49.4 kOhm term, the resistor for a gain of 10 is 5.489 kOhm, for a gain of 100 it is 499 Ohm and for a gain of 1000 it is 49.45 Ohm. The nearest E96 values are 5.49 kOhm, 499 Ohm and 49.9 Ohm, and the last one is a 0.9 per cent gain error on its own, so a gain of 1000 needs a 0.1 per cent resistor or a trim.

The 35 ppm per degree of gain drift above unity gain excludes the external resistor. A 25 ppm per degree resistor in series with that term doubles the drift of the stage, so the resistor temperature coefficient, not the amplifier, sets the drift budget at high gain, and a 5 ppm per degree resistor is the cheap way to keep the published figure.

Driving a converter from the output

The output sits within 0.15 V of either rail and is stable into 1000 pF, so a short trace to a sampling converter is inside the load the part was specified for. What the datasheet does not promise is recovery from the charge injection of a switched input capacitor, so a 50 to 100 Ohm series resistor between the amplifier and the converter is the usual addition, and the 20 mA short circuit limit is what protects the stage if that resistor is left out.

Where this order code fits

Bridge sensors, flow and pressure transmitters, battery test equipment, ECG front ends and precision data acquisition are the applications the vendor names, and every one of them presents a small differential signal on a common mode that may sit well away from the middle of the supply. Teams comparing it with a neighbouring part start from our Amplifier Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

Is the 35 uV offset the figure I get at unity gain? No. At unity gain the output stage offset adds directly, so the limit is 435 uV. The 35 uV figure applies to the input stage alone and only becomes the total at high gain.

Can it run from a 3.3 V rail? No. The minimum single supply is 4.5 V, and the input window needs 2 V of headroom from each rail, so a 3.3 V rail leaves no usable common mode range.

Does the DGK body have the same offset as the SOIC? No. The DGK limit is 40 uV against 35 uV in the D and DRG bodies, so the body on the order changes the guaranteed number.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.