UCC21540DWR
Product Specifications
UCC21540DWR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC21540DWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC21540DWR: a reinforced isolated dual channel gate driver with 5.7 kVRMS of isolation, 4 A of source and 6 A of sink current, programmable dead time and an 8000 V peak surge rating, in the sixteen pin wide SOIC on a 2000 piece reel
UCC21540DWR is a dual channel driver that provides a reinforced barrier between a low voltage controller and two power switches, and that can be configured as a half bridge, two high side drivers or two low side drivers without an external isolator in a SOIC body of 16 pins. The DW body is the sixteen pin wide SOIC and it is pin to pin with the UCC21520, so a board qualified on that part takes this one without a change. The DWK fourteen pin body is the variant with 3.3 mm of channel to channel spacing.
Order code and package
| Catalogue string | UCC21540DWR, where 21540 is the dual channel driver, DW is the sixteen pin wide SOIC and R is the large reel |
| Body | SOIC, DW outline, sixteen pins, pin to pin with the UCC21520, with a DWK fourteen pin body offered for the wider channel to channel spacing |
| Reel | 2000 pieces on a large reel for this body, the same quantity as the DWK body, so the body change does not change the packing |
| Status | Active in production, with the plain row and the .A row both listed at the same quantity |
| Finish and moisture | NIPDAU at moisture level 2 for 260 C with a one year floor life |
| Isolation | 5.7 kVRMS for one minute per UL 1577, 8000 V peak reinforced per VDE 0884-17, and CQC certification to GB4943.1-2022 |
| Temperature | minus 40 to 125 C on the addendum rows for this body |
| Document | SLUSDE1E, September 2018, revised November 2024 |
Electrical parameters that decide the application
| Output supply | up to 18 V on VDD, with a 9.2 V minimum recommended supply for the DW member and 6.0 V for the A member in the DWK body |
| Lockout options | 5 V and 8 V output lockout versions in the family, so a logic level MOSFET rail and an IGBT gate rail are covered by the same die with a different suffix |
| Propagation delay | 33 ns typical in both directions, which is short enough that the driver is not the dominant term in the dead time budget |
| Pulse width distortion | 6 ns maximum between the two edges, which is the number that produces a DC offset in a transformer coupled stage |
| Power up delay | 10 microseconds maximum from the output supply crossing its lockout to the output being enabled, the window in which both inputs have to be held low |
| Dead time | set by a resistor from the DT pin, applied between the two channels, so the interval does not depend on the controller |
| Common mode immunity | above 125 V per nanosecond, which keeps a fast switching node from producing a false command through the barrier |
| Input levels | TTL and CMOS compatible, with negative voltage handling to minus 5 V for 50 ns on the input pins, so the ringing on an input trace does not damage the part |
| Drive strength | 4 A peak source and 6 A peak sink per channel, with the two channels independent and each with its own output supply |
| Disable | a disable pin turns both outputs off together, which is the fast shutdown path for a bridge fault |
| Channel spacing | the DWK body provides 3.3 mm minimum between channels, which allows a higher bus voltage between the high side and the low side of the same package |
| Pinout | pin to pin with the UCC21520, so a board already qualified on that part does not need a change to accept this one |
Family variants and how they differ
| UCC21540 | the 4 A and 6 A member in the sixteen pin wide SOIC, with a 9.2 V minimum recommended output supply |
| UCC21540A | the A member, offered in the fourteen pin DWK body with a 6.0 V minimum recommended supply and the 3.3 mm channel spacing |
| UCC21541 and 21542 | other members of the same family with the same barrier and pinout, differing in drive strength and lockout |
| UCC21520 | the predecessor with the same pinout in the wide SOIC, which is why an upgrade does not change the board |
| Isolation families | the same 5.7 kVRMS reinforced barrier appears in the single channel drivers, so a mixed bridge can use one document for the isolation rules |
| Packages | DW sixteen pin and DWK fourteen pin, both at 2000 pieces on a large reel, with the DWK obsolete row on the plain string and the .A row active |
Points to check before this part goes on a BOM
Reinforced isolation is the difference between this part and the lower cost dual drivers. A 5.7 kVRMS barrier with an 8000 V peak surge and a CQC certificate is what a medical or a grid connected product needs, and a 3 kVRMS functional barrier cannot be substituted on the same board without changing the safety case.
The 9.2 V minimum recommended supply for this member is a working limit, not a lockout. Below it the output stage does not guarantee the gate voltage that turns a standard MOSFET fully on, and a board that runs the output supply at 8 V from a bootstrap rail sits inside that margin on every cycle.
Six nanoseconds of pulse width distortion is the figure that decides whether a half bridge needs a blocking capacitor. At 100 kHz that is 0.06 per cent of the period, and a transformer coupled gate drive with that asymmetry produces a small DC bias that grows over temperature if the coupling capacitor is undersized.
The minus 5 V input spike handling for 50 ns is a real requirement on a bridge board. The input traces run next to the switching node, and a negative spike on an input pin is the common cause of a driver that fails after a few hundred hours rather than at first power up.
The DWK body with 3.3 mm of channel spacing exists for a reason: at 800 V between the high side and the low side, the creepage inside the package becomes part of the isolation coordination, and the sixteen pin body may not provide it. A substitution between the two bodies is a change to the safety case, not just to the footprint.
Choosing between the two bodies
The sixteen pin DW body is pin to pin with the part it replaces and carries the higher recommended output supply. The fourteen pin DWK body gives 3.3 mm between channels and a 6.0 V minimum supply, which suits a lower gate voltage and a higher bus voltage at the same time.
The choice is made by the bus voltage and the gate drive rail, not by availability. Where the bus is above 400 V and the two channels share a package, the channel spacing has to be checked against the creepage requirement of the standard the product is certified to.
Where this order code fits
Reinforced isolated gate drive in solar and storage inverters, motor drives, server and telecom power, medical power supplies, and any bridge stage where the barrier has to be certified rather than functional Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Consolidation page.
Questions buyers ask
Is the isolation reinforced? Yes. 5.7 kVRMS for one minute per UL 1577, 8000 V peak reinforced per VDE 0884-17 and CQC certification, which is the level a medical or grid connected product needs.
Can it replace a UCC21520 directly? Yes, the DW body is pin to pin with the UCC21520, so the board does not change. The output supply range and the lockout version still have to be checked.
What sets the dead time? A resistor from the DT pin, applied between the two channels, so the interval is fixed by the driver rather than by the controller.
Why two package options? The fourteen pin DWK body provides 3.3 mm of channel to channel spacing for a higher bus voltage, while the sixteen pin DW body matches the earlier pinout. The body choice is part of the isolation coordination.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.