UCC27301ADR
Product Specifications
UCC27301ADR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC27301ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC27301ADR: half bridge gate driver with an input interlock and an integrated bootstrap diode
UCC27301ADR is a half bridge gate driver for two N channel MOSFETs in a SOIC body of 8 pins. It drives the high side and the low side of a synchronous buck or a half bridge from two independent TTL compatible inputs, carries a 120 V bootstrap diode inside the package, and pulls both outputs low when the two inputs overlap. The D body is the plain eight pin SOIC, the DDA body adds a thermal pad, and the DRC body is the ten pin VSON that is the only one with the enable pin.
Order code and package
| UCC27301ADR | D body, eight pin SOIC, 3000 pieces on a large reel, active in the packing addendum dated November 2025 |
| UCC27301ADRCR | the same body and the same 3000 piece reel, a second row of the addendum |
| UCC27301A Q1 DRC | ten pin VSON, 3 mm by 3 mm, the automotive row with the enable pin |
| DDA body | eight pin SOIC with the exposed pad, no enable pin |
Electrical parameters that decide the application
| Peak output current | 3.7 A source and 4.5 A sink |
| Propagation delay | 19 ns typical on the falling edge, 20 ns typical on the rising edge, 30 ns and 42 ns maximum |
| Delay matching between the two channels | 4 ns typical, 9.5 ns maximum at 25 C, 17 ns maximum over minus 40 to 150 C |
| Rise and fall time | 7.2 ns and 5.5 ns into a 1000 pF load |
| Output supply | 8 V to 17 V recommended, 20 V absolute maximum, lockout on both the supply and the bootstrap rail |
| Bootstrap and switch node | 120 V absolute maximum on HB and HS, 115 V recommended floating supply above VSS |
| Input pins | minus 10 V to plus 20 V absolute independent of the supply, thresholds 1.2 to 1.9 V low and 1.7 to 2.55 V high, 68 kOhm pull down |
| Bootstrap diode | 0.65 V typical at 100 uA, 0.9 V at 100 mA, 0.3 to 0.85 Ohm dynamic resistance |
| Junction temperature | minus 40 to plus 150 C |
| ESD | 2000 V human body model, 1500 V charged device model |
Family variants and how they differ
| D body | eight pin SOIC without the enable pin, 3000 piece reel, no exposed pad |
| DDA body | eight pin SOIC with the PowerPAD, still no enable pin, the pad is the thermal path |
| DRC body | ten pin VSON with the enable pin, 1.3 uA typical and 3 uA maximum supply current while disabled, 0.1 us to enable and 0.7 us to disable |
| Automotive row | the Q1 string has its own qualification document even though it shares the DRC body |
Points to check before this part goes on a BOM
The interlock is the feature that protects the bridge. Both outputs go low whenever LI and HI are high at the same time, so a controller that can issue overlapping commands cannot turn both MOSFETs on together.
The bootstrap diode is inside the package and rated to 120 V. Its forward drop is 0.65 V typical at 100 uA but 0.9 V at 100 mA, and the dynamic resistance is 0.3 to 0.85 Ohm, so the charging path is stiffer at the start of the on time than a discrete silicon diode would be.
The switch node is rated to minus 1 V DC and to a repetitive pulse of minus 28 V minus VDD below 100 ns. That window covers the undershoot from the parasitic inductance of the low side source and the board loop, which is the usual reason a driver dies on a bridge that looks correct on paper.
The lockout acts on both rails but not in the same way. A supply below the VDD threshold holds both outputs low, while a bootstrap capacitor that has not charged disables only the high side output, so the fault shows up as a missing high side pulse rather than a dead driver.
The enable pin belongs to the DRC body alone. With the pin low the supply current falls to 1.3 uA typical and 3 uA maximum, the enable threshold is 2.3 V typical with 0.7 V of hysteresis, and the pin carries an 80 kOhm internal pull down so a floating pin keeps the driver off.
The DDA body has a thermal pad and the D body does not. On a bridge switching at 20 kHz with 60 nC of gate charge the difference is the difference between an auxiliary supply that survives a sealed enclosure and one that does not, and the pad is the only path to the copper that carries the heat away.
The 20 ns propagation delay and the 30 to 42 ns maximum are not the same promise. A loop that closes through the driver has to work with the maximum, while a bridge that only needs dead time has to work with the 4 ns matching figure, which is why the document prints both instead of one headline number.
What the two current figures mean on a real board
The 3.7 A and 4.5 A are peak currents at the output pin, not continuous ratings. What limits a board is the gate charge that has to be moved at the switching frequency and the thermal path out of the package, so a 60 nC gate at 200 kHz draws 12 mA of average current from the supply but still asks for the full peak current on every edge. The thermal section of the document is where the junction temperature is checked once peak current and frequency are known.
The 4 ns delay matching matters when the two channels drive the same bridge. A mismatch becomes a small dead time error on every cycle, and on a synchronous buck that error shows up as body diode conduction on one side and extra loss on the other. The over temperature figure of 17 ns is the number to work to, not the 9.5 ns measured at 25 C.
Reading the absolute maximum table correctly
The 120 V on HB and HS is an absolute maximum, not a working voltage. The description gives 115 V as the highest floating supply above VSS, and the five volt gap is the margin for the overshoot that appears when the high side switch turns off into a parasitic inductance. A board that runs the bootstrap at 118 V looks legal in the table and fails in the field.
The input pins are rated minus 10 V to plus 20 V independent of the supply, which is wider than most controllers allow. That rating is what lets the driver sit behind a gate drive transformer or a level shifter that swings below ground, and it is also why the input thresholds are specified as fixed windows rather than as fractions of VDD.
Where this order code fits
Solar micro inverters, telecom rectifiers, online and offline UPS and battery test equipment are the four applications the vendor lists, and all four want the same thing from a driver: a hard gate edge and no shoot through. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Can the driver run from a 12 V auxiliary rail? Yes. The recommended supply window is 8 V to 17 V, so 12 V sits in the middle of it, and the absolute maximum is 20 V, which leaves room for the spike on a poorly damped auxiliary winding.
Is an external bootstrap diode needed? No. The diode is inside the package and rated to 120 V, so only the bootstrap capacitor and its series resistor are external.
What happens if the controller drives both inputs high? The interlock pulls both outputs low. The device does not latch, so normal operation resumes once one input goes low again.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.