Contact Us

THS6042ID

Brand: Texas Instruments
Texas Instruments THS6042ID is a power management component designed for general electronics and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

THS6042ID — Power Management & Signal Chain | Superb Automation

THS6042ID

Texas Instruments — Power Management & Signal Chain

Product Overview

The THS6042ID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

THS6042ID: dual ADSL line driver specified for plus or minus 12 V rails into a 25 ohm line

THS6042ID is a dual current feedback driver with the distortion table written for a 16 V peak to peak multicarrier output, which is the working condition of a central office line card in a SOIC body of 8 pins. The D suffix is the 8 pin SOIC, and the specifications are taken at plus or minus 12 V with a 750 ohm feedback resistor and a 100 ohm load, which is closer to a real line transformer than a 50 ohm bench load. Small signal bandwidth is 95 MHz at a gain of 2 into 25 ohms and 75 MHz at a gain of 4, slew rate is 1000 V per microsecond at plus or minus 15 V, and third order distortion is minus 75 dBc with a 16 V peak to peak output at 250 kHz.

Order code and package

Order codeTHS6042ID
Functiondual differential line driver, current feedback
PackageSOIC, 8 pins, body code D
Supply rangeplus or minus 6 V to plus or minus 15 V, 10 to 30 V single supply
Output current400 mA short circuit
Bandwidth95 MHz at a gain of 2 into 25 ohms, 75 MHz at a gain of 4
Slew rate1000 volts per microsecond, 1200 at 12 V peak to peak on 12 V rails
Quiescent current7.4 mA typical, 9.5 mA maximum per driver at 12 V
Output swingplus or minus 10.3 to plus or minus 10.8 V into 100 ohms
Shutdown pinnone on this order code
Junction rangeminus 40 to plus 85 C, I suffix
DatasheetSLOS229, revision with the 6043 shutdown table

Electrical parameters that decide the application

Offset voltage9.5 mV typical, 16 mV maximum
Differential offset1 mV typical, 5 mV maximum
Offset drift20 microvolts per degree, differential 10 microvolts per degree
Bias current3.5 microamps typical, 10 microamps maximum, 6 microamps over temperature
Voltage noise2.2 nanovolts per root hertz at 10 kHz
Common-mode rejection55 dB minimum, 59 to 68 dB typical
Input common modeplus or minus 9.6 to plus or minus 10.1 V at 12 V rails
Third order distortionminus 75 dBc at 16 V peak to peak, minus 79 dBc at 2 V peak to peak
Output swing into 25 ohmsplus or minus 7.5 to plus or minus 9.1 V
Full power bandwidth1 MHz at 12 V peak to peak on 12 V rails
Channel separationmeasured with the two feedback networks at 390 and 500 ohms
Package dissipation8 pin SOIC, thermal limit set by the lead frame

Points to check before this part goes on a BOM

The distortion table is written at the amplitude a line actually runs. Minus 75 dBc belongs to a 16 V peak to peak output at 250 kHz on 12 V rails, and the same part gives minus 72 dBc at 2 V peak to peak into 25 ohms. A bench measurement at 1 V peak to peak will look better than the line condition and is not a qualification.

Offset is an order of magnitude worse than a precision amplifier, and that is by intent. The 16 mV maximum offset of the driver as a whole becomes 1 mV to 5 mV when measured differentially, which is the number that matters for a transformer coupled pair, because the common mode offset is absorbed by the transformer and the differential part is not.

Bias current of 10 microamps maximum limits the feedback network. Through a 750 ohm feedback resistor that is 7.5 mV of offset at the output, and through a 1 kilohm resistor it is 10 mV. Raising the feedback resistor to save supply current therefore buys noise and costs offset, and the data sheet's 390 to 750 ohm range is the region where both stay acceptable.

Slew rate falls with the rail. The same output stage gives 1200 V per microsecond at 12 V peak to peak on 12 V rails, 1000 V per microsecond at 15 V and 600 V per microsecond at 6 V. A board that keeps the 1000 V figure in its timing budget while running 6 V rails will find the full power bandwidth halved.

Quiescent current is specified per driver and at 12 V, not at the absolute maximum rail. At 7.4 mA typical and 9.5 mA maximum per driver, a line card with eight ports spends about 180 mW per port before any signal, and that heat is inside the same small package that has to deliver the drive current.

There is no shutdown pin on this order code. The identical die with shutdown is the THS6043, and a board that needs per port power down has to order that part number; adding an external switch in the supply of a 7.4 mA device costs more board area than the suffix change.

Where this order code fits

Central office ADSL line cards, HDSL repeaters and any transformer coupled driver that has to hold linearity at 16 V peak to peak use this part. It also turns up in high voltage arbitrary waveform outputs where a plus or minus 12 V rail is already available and the load is a few tens of ohms. Boards comparing it with a neighbouring part start from our How to Verify a Drop in Replacement page, and boards replacing a part that has gone end of life start from the Amplifier Cross Reference page.

Questions buyers ask

What is the difference between the THS6042 and the THS6043? Same amplifier and same distortion table. The 6043 adds a shutdown pin with 0.3 mA typical standby current, 0.5 microsecond disable and 0.2 microsecond enable, which is what a line card needs for per port power management.

Can this run from a single 12 V supply? The data sheet covers 10 to 30 V single supply operation, and the input common mode then sits around half the rail. The distortion figures quoted here are for split rails, so a single supply board has to re-qualify them.

Why is the quiescent current quoted per driver? Because each half has its own supply pins and its own bias network. Two drivers at 9.5 mA maximum is 19 mA per package at 12 V rails, roughly a quarter of a watt before any output current.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Obsolete Part Cross Reference Hub page sets out the checks that keep a substitute from failing on the bench.