Contact Us

OPA627AU

Brand: Texas Instruments
Texas Instruments OPA627AU is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA627AU — Power Management & Signal Chain | Superb Automation

OPA627AU

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA627AU from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA627AU: precision JFET-input operational amplifier with 500 microvolt maximum offset in an 8-pin SOIC

OPA627AU is a precision operational amplifier with a dielectric isolated JFET input, 280 microvolts typical offset and a 45 MHz gain bandwidth into a 30 picofarad load in a SOIC body of 8 pins. The AU suffix is the A grade in the 8-pin SOIC, which the datasheet lists as active production while the metal can AM grade is on last time buy. Offset on this grade is 280 microvolts typical and 500 microvolts maximum, bias current is 2 picoamps typical at 25 C, and the revision history records two changes that matter more than the headline: gain bandwidth moved from 16 MHz to 45 MHz with a 30 picofarad load, and slew rate moved from 55 to 150 volts per microsecond.

Order code and package

Order codeOPA627AU
Functionprecision operational amplifier with dielectric isolated JFET input
PackageSOIC, 8 pins, body code D
Supply rangeplus or minus 4.5 V to plus or minus 18 V
Supply current7 milliamps typical, 7.5 milliamps maximum
Gain bandwidth45 MHz with a 30 picofarad load, 16 MHz in the family headline
Slew rate150 volts per microsecond typical, revised from 55
Offset280 microvolts typical, 500 microvolts maximum on the A grade
Input bias current2 picoamps typical at 25 C, nanoamp class over temperature
Settling120 nanoseconds to 0.01 percent, revised from 550
Output current30 milliamps, short circuit 45 milliamps
DatasheetOPA627, OPA637 family document with the 2023 revision history

Electrical parameters that decide the application

Offset trimpins 1 and 5, floating when unused
Grade comparisonthe B grade is 25 microvolts typical and 125 microvolts maximum with 0.3 microvolts per degree of drift
Common-mode rejection106 dB minimum, 116 dB typical on the B grade
Open-loop gain106 dB minimum, 116 dB typical into 1 kilohm
Input common modeplus or minus 10.5 V on a plus or minus 15 V supply
Input impedanceJFET input with a 9 picofarad common-mode capacitance
BodiesSOIC for the AU and BU, TO-99 for the AM and BM, the AM on last time buy
Operating rangeminus 25 to plus 85 C for the A and B grades

Points to check before this part goes on a BOM

The revision history is the most useful page in this datasheet. Gain bandwidth on the AU moved from 16 MHz to 45 MHz once a 30 picofarad load condition was added, slew rate moved from 55 to 150 volts per microsecond, settling moved from 550 to 120 nanoseconds, and output current was cut from 45 to 30 milliamps. A quotation or a benchmark written before that revision therefore describes a different part, and a board that oscillates with a capacitive load is outside the condition under which the 45 MHz figure was taken.

The A grade offset window is 280 microvolts typical and 500 microvolts maximum, and the B grade is 25 microvolts typical, 125 microvolts maximum with 0.3 microvolts per degree of drift. The two grades are the same silicon sorted, so a board that needs 500 microvolts should buy the A and a board that needs 125 should buy the B. Ordering the A and hoping for a B is what happens when a BOM is copied from a competitor's board.

Two picoamps of bias current through a 10 megohm feedback resistor is 20 microvolts, which is a sixteenth of the offset. That is the reason a JFET input is chosen for a charge amplifier: a bipolar part at 40 nanoamps would put 400 millivolts across the same resistor. Over temperature the leakage rises to the nanoamp class, so the same resistor then contributes 10 millivolts, and the room temperature bias figure is not the one to size the DC loop around.

30 milliamps of output current into a 1 kilohm load is 30 V, which the supply cannot deliver, so the real limit is the output swing of about plus or minus 10.5 V at the input and slightly more at the output. Into 600 ohms the current rating and the swing both apply, and into 100 ohms the part is current limited at 30 milliamps, which is 0.3 V of swing. The revised 30 milliamp figure is lower than the older 45, and a load that was marginal before the revision is now outside the rating.

150 volts per microsecond at a 20 V peak to peak signal gives a full power bandwidth of about 1.2 MHz, and 45 MHz of gain bandwidth gives 4.5 MHz at a gain of 10. For a charge amplifier with a 1 megohm transimpedance and 10 picofarads of source capacitance the noise gain rises with frequency and the closed loop bandwidth collapses anyway, so the 45 MHz figure describes the amplifier and not the circuit. Calculating the actual bandwidth from the source capacitance is the only number that matters.

The metal can AM grade is on last time buy while the AU and BU SOIC codes are active production. For a board that is being re-qualified, that difference decides whether the existing footprint can stay: the SOIC is a different thermal path and a different board mounting, and a hermetic can cannot be replaced by an SOIC without a substrate change. This is the sort of status line that belongs on a BOM review rather than being discovered at the last buy notice.

Where this order code fits

Charge amplifier and photodiode front ends, high impedance transducer conditioning, precision attenuators and any stage where bias current has to be in the picoamps while bandwidth runs to megahertz use this part. The JFET input and the 500 microvolt offset window are the two specifications that keep it in sockets that were built twenty years ago. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Is the OPA627AU the same as the OPA627AM? Same die, different grade and body. The AU is the A grade in SOIC, the AM is the military grade in a TO-99 can and is on last time buy, so the can is not a long term supply route.

Why does the gain bandwidth differ between documents? Because the figure was revised from 16 MHz to 45 MHz once a 30 picofarad load condition was added. Any older quotation or benchmark that says 16 MHz is describing the earlier revision.

What load capacitance does the 45 MHz figure assume? 30 picofarads. Above that the part needs either an isolation resistor or a different compensation, because the output impedance and the load capacitance form a pole inside the loop.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Obsolete RF Part Replacement page sets out the checks that keep a substitute from failing on the bench.