TPS562207DRLR
Product Specifications
TPS562207DRLR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS562207DRLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS562207DRLR: 4.3 V to 17 V, 2 A synchronous buck in a six pin SOT563
TPS562207DRLR is a synchronous buck converter with both switches inside the package and a fixed frequency control loop in a SOT563 body of 6 pins. It takes a 12 V or 5 V rail down to a point of load in one stage, with no external compensation, no diode and no current sense resistor.
Order code and package
| Order code | TPS562207DRLR, DRL package, 3000 pieces on a large reel |
| Body | SOT563, 1.6 mm by 1.6 mm, six pins, no exposed pad |
| Conduction mode | Forced continuous only, the inductor current is allowed to reverse at light load |
| Control | D-CAP2 adaptive on time, internally compensated, ceramic output capacitors only |
| Reference | 0.804 V typical at 25 C, 788 mV to 820 mV across the window |
| Output range | 0.804 V to 7 V set by two external resistors |
Electrical parameters that decide the application
| Input range | 4.3 V to 17 V operating, 19 V absolute maximum on VIN, 21 V for a 10 ns transient |
| Output current | 2 A continuous, 3.1 A typical valley limit, 2.24 A minimum over the full range |
| High side switch | 140 mOhm typical at 25 C, gate driven from the bootstrap capacitor |
| Low side switch | 84 mOhm typical at 25 C |
| Switching frequency | 580 kHz nominal, pseudo fixed, moves with input and output voltage |
| Minimum off time | 220 ns typical, 310 ns maximum, which is what limits the maximum duty cycle |
| Soft start | 1.2 ms internal, monotonic into a pre-biased output |
| Quiescent current | 590 uA typical and 750 uA maximum while switching, 1 uA to 3 uA in shutdown |
| Enable threshold | 1.35 V to 1.6 V high, 0.8 V to 1.05 V low, 225 kOhm to 900 kOhm from EN to ground |
| Protection | Valley current limit each cycle, hiccup after 2.2 ms with an 18 ms retry, thermal shutdown at 160 C |
Family variants and how they differ
| TPS562212 | 2 A from 18 V in an eight pin SOT-5X3 body, selectable Eco-mode, so lower standby current in a different footprint |
| TPS563201 | 3 A in a six pin SOT-23 with pulse skip and a 768 mV reference, one body size larger |
| TPS56C230 | 12 A in a 20 pin QFN with the same 600 mV class reference, a completely different thermal path |
| TPS62130 | 3 A from 17 V in a 16 pin QFN with DCS control and a selectable 2.5 MHz or 1.25 MHz frequency |
| TPS61252 | a boost for the case where the rail sits below the load voltage, so it is not a substitute here |
Points to check before this part goes on a BOM
This part runs in forced continuous conduction at every load, which means it never skips pulses. At zero load it still switches at 580 kHz and draws 590 uA from the rail, and the inductor current reverses into the low side switch until the 1.1 A sink limit stops it. That behaviour is what keeps the output from floating up when a second source back feeds the rail, and it is also why the part is a poor choice for a battery node that spends most of its life idle.
Loss at 2 A from 12 V to 5 V is arithmetic. The low side switch conducts 58 per cent of the period at 84 mOhm, which is 0.20 W, and the high side conducts 42 per cent at 140 mOhm, which is 0.23 W, so the package sheds about 0.43 W before switching loss. The SOT563 has no exposed pad, so that heat leaves through six pins and the copper under them, and the 2 A figure assumes the board gives it somewhere to go.
The reference is specified at 25 C only, 788 mV to 820 mV, a four per cent window. A 3.3 V output needs a divider ratio of 3.105 to 1, and the reference window alone moves the output by 130 mV before the resistors contribute anything. A board that needs 3.3 V within two per cent has to use one per cent resistors and accept that the reference spread is the larger term, and it should not expect the same accuracy at 85 C where the table gives no window at all.
The 310 ns maximum off time caps the duty cycle at about 82 per cent at 580 kHz. That puts a floor under the input voltage for any given output: 3.3 V needs at least 4.0 V in, 2.5 V needs 3.05 V in, and a 5 V to 5 V pass through is impossible. Boards that want to run from a 5 V rail at minus ten per cent and hold 4.5 V out will find the part in dropout for part of the cycle, not regulating.
Current limit is measured as a valley on the low side switch, so it acts on the bottom of the ripple rather than the average. With 2.24 A minimum and 0.6 A of peak to peak ripple, the average load can reach 2.5 A before the limit is reached, which is above the 2 A rating. The other direction is the trap: a board with 1.5 A of ripple, which is what a small inductor gives, reaches the limit at 1.5 A of average current and the part looks weak for no obvious reason.
The retry behaviour shapes the failure signature. On a short the part holds the low side on, waits 2.2 ms, then waits 18 ms before trying again, so the rail pulses at roughly 50 Hz at five per cent duty. That keeps the dissipation in a hard short low enough to survive, and it also means a voltmeter reads a few hundred millivolts rather than zero, which is often read as a partial short rather than a protection event.
The enable pin is not a high impedance input. It presents 225 kOhm to 900 kOhm to ground at 12 V, so a divider built for a 10 uA budget will have its threshold moved by the pin current, and a 1 MOhm top resistor carries enough current into the pin to shift the turn on point by more than a volt. Any under voltage lockout built from the EN pin has to be checked against that resistance, and the internal pull down is what allows the pin to be left floating on a board that wants the converter always on.
The bootstrap capacitor is the only part the loop needs besides the inductor and the output bank, 0.1 uF between BST and SW. Because BST sits 5.5 V above SW and never above VIN plus 5.5 V, a 10 V rated part is adequate, and the failure mode of a missing or open bootstrap capacitor is a converter that starts and then stops switching after the first cycle. On a board where the part looks dead but the enable and input are correct, that capacitor and its solder joint are the first thing to check.
Start-up into a pre-biased output is monotonic, which matters when a 1.2 V rail is already held by a second regulator or by a large capacitor on a shared bus. The part waits until the internal reference exceeds the feedback voltage and then ramps, so there is no discharge pulse and no reverse current through the load. The 1.2 ms ramp is fixed, so inrush into a large output bank is set by the capacitor value and cannot be slowed without adding a second stage.
Where this order code fits
It belongs on the 5 V or 12 V intermediate rail of a set top box, a display board, a camera or a network appliance, where the load is a fixed few hundred milliamps to 2 A and the board has no room for a controller plus two external switches. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the BOM Shortage Recovery page.
Questions buyers ask
What is the lowest input that still holds 3.3 V? About 4.0 V. The 310 ns maximum off time stops the duty cycle at 82 per cent, and the 4.3 V under voltage lockout is the hard floor in any case, so a 4.5 V rail with five per cent tolerance is the practical minimum.
Does it regulate a zero load? Yes, and it does so by allowing the inductor current to go negative. The part keeps switching and draws 590 uA, so there is no burst behaviour and no output rise from leakage, but there is also no light load efficiency gain.
Can it carry 2.5 A continuously? Not with margin. The 2.24 A minimum valley limit plus half the ripple sets the ceiling at about 2.5 A with a large inductor and lower with a small one, and the six pin body has to shed the extra loss.
What sets the output voltage? Two resistors, one from the output to FB and one from FB to ground, against the 0.804 V reference. There is no pin selectable option, and the reference is specified at 25 C only.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.