Contact Us

TPS22992SRXNR

Brand: Texas Instruments
Texas Instruments TPS22992SRXNR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS22992SRXNR — Power Management & Signal Chain | Superb Automation

TPS22992SRXNR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS22992SRXNR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS22992SRXNR: 6 A load switch with overcurrent protection and a separate bias pin

TPS22992SRXNR is a single channel 6 A load switch with overcurrent protection and adjustable rise time in a WQFN body of 8 pins. The S variant adds overcurrent protection to the thermal shutdown, and the part takes its gate drive from a bias pin rather than from the switched rail.

Order code and package

Order codeTPS22992SRXNR, RXN package, WQFN eight lead
Body1.25 mm by 1.25 mm, 0.4 mm pitch, against 1.5 mm by 1.25 mm and 0.5 mm pitch on the RXP body
Input range1 V to 5.5 V on the S variant, 0.1 V to 5.5 V on the plain TPS22992
Bias range1.5 V to 5.5 V on a separate pin
Rated current6 A with an 8.7 mOhm switch at a 5 V bias

Electrical parameters that decide the application

On resistance8.7 mOhm at a 5 V bias, which is 52 mV and 313 mW at 6 A
Bias pinSupplies the gate drive independently of the switched rail, so the switch stays enhanced at a 1 V input
Enable threshold0.8 V, so a low voltage GPIO drives the pin directly
Rise timeAdjustable, so the inrush into a large capacitance can be traded against power up time
ProtectionThermal shutdown on both variants, overcurrent protection on the S variant only
Body optionsTwo WQFN bodies with different footprints and pitches, which affects the land pattern
Current at 8.7 mOhm6 A through the switch is 313 mW, so the copper under the body is the thermal path

Family variants and how they differ

TPS22992Same switch with a 0.1 V input floor and no overcurrent protection
TPS229204 A with a 5.3 mOhm switch but a 3.6 V input ceiling and no bias pin
TPS22914B2 A in a four bump body for a rail that needs a smaller footprint
TPS2553Adjustable current limit with a flag when protection rather than switching is the requirement
TPS2595eFuse with a programmable limit and a fault output for a rail that must survive a short

Points to check before this part goes on a BOM

The bias pin is the reason this part exists in this form. A load switch that derives its gate drive from the switched rail loses gate headroom as the rail falls, and at 1 V input the switch would sit in its linear region. With a separate 1.5 V to 5.5 V bias the gate is held where the silicon needs it, so the 8.7 mOhm figure holds across the whole input range. The bias pin draws current continuously, and that current belongs in the budget of whatever rail feeds it.

At 6 A the dissipation is 313 mW and the package is 1.25 mm square. There is no way to pass that through the body alone, so the land pattern is part of the specification. The datasheet thermal table gives the junction to ambient resistance for each body on the JEDEC board, and a real board with less copper than the test board will run hotter. A product that runs 6 A continuously should be measured rather than calculated.

The adjustable rise time is what lets the part start into a large capacitance without pulling the upstream rail down. The ramp is set by a component rather than fixed in silicon, so the same order code covers a fast port and a slow bulk rail. The trade is that a slow ramp keeps the switch in its linear region for longer, and the dissipation during the ramp is the load capacitance times the square of the input voltage times the switching frequency of the ramp, which has to be checked against the thermal budget.

The S suffix is the difference between a switch and a protected switch. Thermal shutdown protects the device from a sustained overload, but it acts late and it lets the full short circuit current flow until the junction reaches the trip point. Overcurrent protection acts on the current itself, which is faster and which also protects the upstream rail and the connector. A rail that feeds a user accessible connector needs the S variant, and a rail that feeds a soldered load can use the plain part.

The two bodies are not interchangeable on a board. The RXP body is 1.5 mm by 1.25 mm on a 0.5 mm pitch, and the RXN body is 1.25 mm by 1.25 mm on a 0.4 mm pitch. That means a different land pattern, a different stencil aperture and a different paste volume. An assembly that substitutes one for the other because the part number looks close will produce a joint defect rather than a working board.

The 0.8 V enable threshold is below the 0.9 V figure on the TPS22914, and it means a 1.2 V processor can drive the pin with real margin. The pin still has to be driven, not left floating, because the threshold window is narrow and a floating input can sit in the linear region. A pull down to ground is the safe default for a rail that must stay off until software asks for it.

Eight and a half milliohms is a figure that only holds at a 5 V bias. At a 1.5 V bias the gate drive is lower and the resistance rises, which the datasheet specifies in its own table. A product that biases the part from a 1.8 V rail and expects the 5 V number will find more drop and more heat than the headline suggests, and the bias table is the one to read when the rail is below 3.3 V.

The input range starting at 1 V on the S variant, against 0.1 V on the plain part, is a consequence of the overcurrent comparator needing a supply to work. A rail that has to be switched from zero, such as a battery input that can be fully discharged, needs the plain part or a different scheme. A rail that is always above 1 V, which is every regulated rail, is fine on the S variant.

The bias pin has to be sequenced with the input, or at least present before the enable is asserted. If the enable rises while the bias is still at zero, the switch turns on with no gate drive, which puts the body in its linear region and dissipates the load current across it. The datasheet application section shows the bias tied to a rail that is always on, and the safe rule is that the bias should come from the same rail that powers the controller, not from the rail being switched. A product that biases the switch from its own output will not start at all.

Where this order code fits

It fits a 5 V or 3.3 V rail that carries several amps into a connector or a plug in module, where the inrush has to be controlled and a short on the far side must not take the whole rail down. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the How to Verify a Drop in Replacement page.

Questions buyers ask

What does the bias pin do? It supplies the gate drive independently of the switched rail, so the on resistance stays low even when the input is at 1 V.

What is the difference from the plain TPS22992? The S adds overcurrent protection and raises the minimum input to 1 V.

Is 6 A continuous realistic? Only with the recommended copper; the 313 mW dissipation needs the land pattern from the datasheet.

Can the rise time be slowed for a big capacitor? Yes, the ramp is adjustable so the inrush can be set to what the upstream supply can deliver.

Can it run without a bias supply? No, the bias pin supplies the gate drive and must be present before the enable is asserted.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.